|
|
* 販売終了しました。
DDA 8Zi-Bシリーズ
ディスク・ドライブ・アナライザDDA 8Zi-Bは、デジタル・オシロスコープWaveMaster 8Zi-Bシリーズをベースとした製品で、ディスク・ドライブ解析ツールを搭載した専用装置です。帯域8〜30GHzの3タイプがあり64Mポイントのメモリを装備しています。FC/SAS/SATAなどの高速シリアルインタフェース解析機能(SDAモデルと同等)、複数のセクターをマルチズームで拡大して比較する機能やシリアル・データ・アナライザSDA 8Zi-Bと同等のシリアル・データ・解析機能も搭載しています。(高速シリアル・パターントリガはオプション)
基本仕様
モデル名 |
帯域 |
サンプリング速度
(4ch時/2ch時) |
標準メモリ |
DDA 808Zi-B
販売終了
|
8GHz |
40GS/s (80GS/s*) |
64Mポイント |
DDA 820Zi-B
販売終了
|
20GHz |
40GS/s (80GS/s) |
64Mポイント |
DDA 830Zi-B
販売終了
|
30GHz |
40GS/s (80GS/s) |
64Mポイント |
* インターリーブオプションWM8Zi-2X80GSが必要
|
モデルごとスペック詳細(モデル名をクリックで詳細表示されます)
 DDA 808 Zi-B スペック
Vertical System | Analog Bandwidth (Max) | 8 GHz | Analog Bandwidth @ 50 Ω (-3 dB) (ProLink Input) | 8 GHz (≧10 mV/div) | Analog Bandwidth @ 50 Ω (-3 dB) (ProBus Input) | 3.5 GHz (≧10 mV/div) | Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input) | 500 MHz (typical, ≧2 mV/div) | Rise Time (10-90%, 50 Ω) | 49 ps (test limit, flatness mode) | Rise Time (20-80%, 50 Ω) | 37 ps (flatness mode) | Input Channels | 4 (Any combination of ProLink and ProBus inputs) | Bandwidth Limiters | 20 MHz, 200 MHz, 1 GHz, 4 GHz, 6 GHz | Input Impedance | ProLink Inputs: 50 Ω+/-2% for ≦100 mV/div, 50 Ω+/-3% for >100 mV/div ProBus Inputs: 50 Ω+/-2% or 1 MΩ||16pF, 10 MΩ || 11 pF with supplied Probe | Input Coupling | ProLink Inputs - 50 Ω: DC, GND ProBus Inputs - 1 MΩ: AC, DC, GND; 50 Ω: DC, GND | Maximum Input Voltage | 50 Ω (ProLink): ±2 [email protected]≦100mV/div, [email protected]>100mV/div 50 Ω (ProBus): ±5 Vmax, 3.5 Vrms 1 MΩ (ProBus): 250 V max. (peak AC: < 10 kHz + DC) | Channel-Channel Isolation | DC to 10 GHz: 50 dB (>315:1) 10 to 15 GHz: 46 dB (>200:1) 15 to 20 GHz: 40 dB (>100:1) (For any two ProLink input channels, same or different v/div settings, typical) | Vertical Resolution | 8 bits; up to 11 bits with enhanced resolution (ERES) | Sensitivity | 50 Ω (ProLink): 2 mV-1 V/div, fully variable (2-9.9 mV/div via zoom) 50 Ω (ProBus): 2 mV-1 V/div, fully variable; 1 MΩ (ProBus): 2 mV-10 V/div, fully variable | DC Vertical Gain Accuracy (Gain Component of DC Accuracy) | ±1% F.S. (typical), offset at 0V; ±1.5% F.S. (test limit), offset at 0V | Offset Range | 50 Ω (ProLink): ±500 mV @ 2-100 mV/div ±4 V @ >100 mV/div -1 V/div 50 Ω (ProBus): ±750 mV @ 2-100 mV/div ±4 V @ >100 mV/div -1 V/div 1 MΩ: ±1V @ 2-140 mV/div ±10V @ 142mV-1.40V/div ±100V @ 1.42V-10V/div | Offset Accuracy | 50 Ω (ProLink): 2 mV-1 V/div, fully variable (2-9.9 mV/div via zoom) 50 Ω (ProBus): 2 mV-1 V/div, fully variable; 1 MΩ (ProBus): 2 mV-10 V/div, fully variable | DC Vertical Offset Accuracy | ±(1.5% of offset setting + 1.5% F.S. + 1 mV) (test limit) | | Horizontal System | Timebases | Internal timebase common to 4 input channels | Time/Division Range | 20 ps/div-128 s/div (Real-Time Mode: 20 ps/div - 64 s/div; RIS mode: 20 ps/div - 10 ns/div, user selectable at ≦10ns/div; Roll mode: 100 ms/div up to 128 s/div, user selectable at ≧100 ms/div and ≦5 MS/s), depending on memory length | Clock Accuracy | < 1 ppm + (aging of 0.5ppm/yr from last calibration) | Sample Clock Jitter | up to 10μs Acquired Time Range: 100fsrms (Internal Timebase Reference)
up to 6.4ms Acquired Time Range: 150fsrms (Internal Timebase Reference) | Delta Time Measurement Accuracy | √2*√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) (RMS)+(clock accuracy*reading)(seconds) | Jitter Measurement Floor | √((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) secondsrms (TIE) | Jitter Between Channels | <425fsrms (TIE, typical, measured at maximum bandwidth) | Trigger and Interpolator Jitter | <0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware), | Channel-Channel Deskew Range | ±9 x time/div. setting or 25 ns max. (whichever is larger), each channel | External Timebase Reference (Input) | 10 MHz; 50 Ω impedance, applied at the rear input | External Timebase Reference (Output) | 10 MHz; 50 Ω impedance, output at the rear | | Acquisition System | Single-Shot Sample Rate/Ch | 40 GS/s (80 GS/s on 2 Ch using optional WM8Zi-2X80GS External Interleaving Device) | Random Interleaved Sampling (RIS) | 200 GS/s for repetitive signals (20 ps/div to 10 ns/div) | Maximum Trigger Rate | 1,000,000 waveforms/second (in Sequence Mode, up to 4 channels) | Intersegment Time | 1 μs | Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments) | 64 M / 64 M / 64 M (Memory and Sample Rate can be doubled in 1 or 2 Ch mode with use of WM8Zi-2X80GS External Interleaving Device) (15000) | Memory Options (4 Ch / 2 Ch / 1Ch) (Number of Segments) | L-128 Option: 128M / 128M / 128M (15,000) VL-256 Option: 256M / 256M / 256M (15,000) Note: On all memory options, WM8Zi-2X80GS External Interleaving Device permits 80 GS/s on 1 or 2ch with twice the memory) | | Acquisition Processing | Averaging | Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps | Enhanced Resolution (ERES) | From 8.5 to 11 bits vertical resolution | Envelope (Extrema) | Envelope, floor, or roof for up to 1 million sweeps | Interpolation | Linear or Sin x/x | | Triggering System | Modes | Normal, Auto, Single, and Stop | Sources | Any input channel, Aux, Aux/10, Line, or Fast Edge. Slope and level unique to each source (except line trigger) | Coupling Mode | DC, AC, HFRej, LFRej | Pre-trigger Delay | 0-100% of memory size (adjustable in 1% increments of 100 ns) | Post-trigger Delay | 0-10,000 divisions in real time mode, limited at slower time/div settings or in roll mode | Hold-off by Time or Events | From 2 ns up to 20 s or from 1 to 99,999,999 events | Internal Trigger Range | ±4.1 div from center | Trigger Sensitivity with Edge Trigger (1.85/2.4/2.92mm Inputs) | Not Applicable | Trigger Sensitivity with Edge Trigger ProBus Inputs | 2 div @ < 3.5 GHz, 1.5 div @ < 1.75 GHz, 1.0 div @ < 200 MHz, (for DC coupling, ≧ 10 mV/div, 50 Ω) | Trigger Sensitivity with Edge Trigger ProLink Inputs | 2 div @ < 8 GHz, 1.5 div @ < 3 GHz, 1.0 div @ < 200 MHz, (for DC, AC, LFRej coupling, ≧ 10 mV/div, 50 Ω) | External Trigger Sensitivity, (Edge Trigger) | 2 div @ < 1 GHz, 1.5 div @ < 500 MHz, 1.0 div @ < 200 MHz, (for DC coupling) | Max. Trigger Frequency, SMART Trigger | 2.0 GHz @ ≧ 10 mV/div (minimum triggerable width 200 ps) | External Trigger Input Range | Aux (±0.4 V); Aux/10 (±4 V) | | Basic Triggers | Edge | Triggers when signal meets slope (positive, negative, or either) and level condition. | Window | Triggers when signal exits a window defined by adjustable thresholds | TV-Composite Video | Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative). | | SMART Triggers | State or Edge Qualified | Triggers on any input source only if a defined state or edge occurred on another input source. Holdoff between sources is selectable by time or events. | Qualified First | In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. | Dropout | Triggers if signal drops out for longer than selected time between 1 ns and 20 s. | Pattern | Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don't care. The High and Low level can be selected independently. Triggers at start or end of the pattern. | | SMART Triggers with Exclusion Technology | Glitch | Triggers on positive or negative glitches with widths selectable as low as 200ps to 20 s, or on intermittent faults. | Width (Signal or Pattern) | Triggers on positive, negative, or both widths with widths selectable as low as 200ps to 20 s, or on intermittent faults. | Interval (Signal or Pattern) | Triggers on intervals selectable between 1 ns and 20 s. | Timeout (State/Edge Qualified) | Triggers on any source if a given state (or transition edge) has occurred on another source. Delay between sources is 1 ns to 20 s, or 1 to 99,999,999 events. | Runt | Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns. | Slew Rate | Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. | Exclusion Triggering | Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met | | Cascade (Sequence) Triggering | Capability | Arm on "A" event, then Trigger on "B" event. Or Arm on "A" event, then Qualify on "B" event, and Trigger on "C" event. | Types | Cascade A then B: Edge, Window, Pattern (Logic) Width, Glitch, Interval, Dropout, or Measurement. Measurement can be on Stage B only. Cascade A then B then C (Measurement): Edge, Window, Pattern (Logic), Width, Glitch, Interval, Dropout, or Measurement. Measurement can be on Stage C only. Cascade A then B then C: Edge, Window, Pattern (Logic) | Holdoff | Holdoff between A and B or B and C is selectable by time (1ns to 20s) or number of events. Measurement trigger selection as the last stage in a Cascade precludes a holdoff setting between the prior stage and the last stage. | | High Speed Serial Protocol Triggering | Data Rates | Option WM8Zi-6GBIT-80B-8B10B-TD: 600 Mb/s to 6.5 Gb/s, Channel 4 input only Option WM8Zi-14GBIT-80B-8B10B-TD: 600 Mb/s to 14.1 Gb/s, Channel 4 input only | Pattern Length | 80 bits NRZ, eight 8b/10b symbols, 64b/66b symbol | Clock and Data Outputs | No Clock and Data Recovery outputs provided | | Low Speed Serial Protocol Triggering (Optional) | Optionally available | I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay, I2S (Audio), MIL-1553 | | Measurement Trigger | Measurement Trigger Capability | Select from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger. | | Color Waveform Display | Type | Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen | Resolution | WXGA; 1280 x 768 pixels. | Number of traces | Display a maximum of 16 traces (up to 40 with some software options). Simultaneously display channel, zoom, memory and math traces. | Grid Styles | Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y | Waveform Representation | Sample dots joined, or sample dots only | | Internal Waveform Memory | Internal Waveform Memory | 12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity. | | Integrated Second Display | Type | Supports touch screen integration of user-supplied second display with split-grid capability. (Note: touch screen driver for second display may not be a Fujitsu driver) | Resolution | Determined by display chosen by user | | LeCroy WaveStream Fast Viewing Mode | Intensity | 256 Intensity Levels, 1-100% adjustable via front panel control | Types | Select analog or color-graded | Number of Channels | up to 4 simultaneously | Max Sampling Rate | 40 GS/s (80 GS/s with optional WM8Zi-2X80GS external interleaving device) | Persistence Aging | Select from 500 ms to Infinity | Waveforms/second (continuous) | up to 2500 Waveforms/second | Operation | Front panel toggle between WaveStream ON (Analog), ON (Color) and OFF | | Analog Persistence Display | Analog and Color-Graded Persistence | Variable saturation levels; stores each trace's persistence data in memory | Persistence Types | Select analog, color, or three-dimensional | Trace Selection | Activate persistence on all or any combination of traces | Persistence Aging | Select from 500 ms to infinity | Sweep Display Modes | All accumulated, or all accumulated with last trace highlighted | | High Speed Digitizer Output (Option) | Type | LeCroy LSIB | Transfer Rate | up to 325 MB/s (typical) | Output Protocol | PCI Express, Gen 1 (4 lanes utilized for data transfer) | Control Protocol | TCP/IP | Command Set | Via Windows Automation, or via LeCroy Remote Command Set | | Processor/CPU | Type | Intel Core i7-4770S Quad, 3.1 GHz (up to 3.9 GHz in Turbo mode) (or better) | Processor Memory | 8 GB standard for STD memory (20 Mpt), S-32 and M-64 memory options 16 GB standard for L-128 and VL-256 memory options Up to 32 GB optional | Operating System | Microsoft WindowsR 7 Professional Edition (64-bit) | Real Time Clock | Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks. | | Zoom Expansion Traces | Zoom Expansion Traces | Display up to 12 Zoom and 12 Math/Zoom traces | | Setup Storage | Front Panel and Instrument Status | Store to the internal hard drive, over the network, or to a USB-connected peripheral device. | | Interface | Remote Control | Via Windows Automation, or via LeCroy Remote Command Set | Network Communication Standard | VXI-11 or VICP, LXI Class C (v1.2) Compliant | GPIB Port | Supports IEEE - 488.2 | LSIB Port (optional) | Supports PCIe Gen1 x4 protocol with LeCroy supplied API | Ethernet Port | Supports 10/100/1000BaseT Ethernet interface (RJ45 port) | USB Ports | 4 rear USB 3.0 ports, 3 front panel USB 2.0 ports support Windows compatible devices | External Monitor Port | Full-size DisplayPort connnector Includes support for extended desktop operation with second monitor. | Peripheral Bus | LeCroy LBUS standard | | Auxiliary Input | Signal Types | For External Trigger Input | Coupling | 50 Ω: DC; 1 MΩ: AC, DC, GND | Max. Input Voltage | 50 Ω: 5 Vrms; 1 MΩ: 250 V (Peak AC < 10 kHz + DC) | | Auxiliary Output | Signal Types | Select from calibrator, control signals or Off | Output Signal | 500 Hz-5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0-1 V into 1 MΩ) | Control Signals | Trigger enabled, trigger out, pass/fail status, off | Connector Type | BNC, located on front | | Automatic Setup | Auto Setup | Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals | Find Vertical Scale | Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range | | General | Auto Calibration | Ensures specified DC and timing accuracy is maintained for 1 year minimum. | | Probes | Probes
| Qty. (4) ÷10 Passive Probes | Probe System | Probus and ProLink. Automatically detects and supports a variety of compatible probes | Scale Factors | Automatically or manually selected depending on probe used | Calibration Output | Cal Output: 1kHz square wave, 1Vp-p (typical), output to probe hook. | | Power Requirements | Voltage | 100-240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection, Installation Category II | Max. Power Consumption | 975 W / 975 VA | | Environmental and Safety | Temperature (Operating) | +5 °C to +40 °C | Temperature (Non-Operating) | -20 °C to +60 °C | Humidity (Operating) | 5% to 80% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C. | Humidity (Non-Operating) | 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F | Altitude (Operating) | Up to 10,000 ft. (3048 m) at or below +25 °C | Altitude (Non-Operating) | Up to 40,000 ft. (12,192 m) | Random Vibration (Operating) | 0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes | Random Vibration (Non-Operating) | 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes | Functional Shock | 20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total | | Physical Dimensions | Dimensions (HWD) | 14"H x 18.4"W x 16"D (355 x 467 x 406 mm) | Weight | 51.5 lbs. (23.4 kg) | Shipping Weight | 70.0 lbs. (31.8 kg) | | Certifications | Certifications | CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, EN61010-2-030, UL 61010-1 3rd edition, and CSA C22.2 No. 61010-1-12 | | Warranty and Service | Warranty and Service | 3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services. | |
 DDA 820 Zi-B スペック
Vertical System | Analog Bandwidth (Max) | 20 GHz | Analog Bandwidth @ 50 Ω (-3 dB) (ProLink Input) | 20 GHz (≧10 mV/div) | Analog Bandwidth @ 50 Ω (-3 dB) (ProBus Input) | 3.5 GHz (≧10 mV/div) | Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input) | 500 MHz (typical, ≧2 mV/div) | Rise Time (10-90%, 50 Ω) | 22 ps (test limit, flatness mode) | Rise Time (20-80%, 50 Ω) | 16.5 ps (flatness mode) | Input Channels | 4 (Any combination of ProLink and ProBus inputs) | Bandwidth Limiters | 40 GS/s mode: 20 MHz, 200 MHz, 1 GHz, 4 GHz, 6 GHz, 8 GHz, 13 GHz, 16 GHz 80 GS/s Mode: 13 GHz, 16 GHz | Input Impedance | ProLink Inputs: 50 Ω+/-2% for ≦100 mV/div, 50 Ω+/-3% for >100 mV/div ProBus Inputs: 50 Ω+/-2% or 1 MΩ||16pF, 10 MΩ || 11 pF with supplied Probe | Input Coupling | ProLink Inputs - 50 Ω: DC, GND ProBus Inputs - 1 MΩ: AC, DC, GND; 50 Ω: DC, GND | Maximum Input Voltage | 50 Ω (ProLink): ±2 [email protected]≦100mV/div, [email protected]>100mV/div 50 Ω (ProBus): ±5 Vmax, 3.5 Vrms 1 MΩ (ProBus): 250 V max. (peak AC: < 10 kHz + DC) | Channel-Channel Isolation | DC to 10 GHz: 50 dB (>315:1) 10 to 15 GHz: 46 dB (>200:1) 15 to 20 GHz: 40 dB (>100:1) (For any two ProLink input channels, same or different v/div settings, typical) | Vertical Resolution | 8 bits; up to 11 bits with enhanced resolution (ERES) | Sensitivity | 50 Ω (ProLink): At 40 GS/s: 2 mV-1 V/div, fully variable (2-9.9 mV/div via zoom) At 80 GS/s: 2 mV-500mV/div, fully variable (2-19.9 mV/div via zoom) 50 Ω (ProBus): 2 mV-1 V/div, fully variable; 1 MΩ (ProBus): 2 mV-10 V/div, fully variable | DC Vertical Gain Accuracy (Gain Component of DC Accuracy) | ±1% F.S. (typical), offset at 0V; ±1.5% F.S. (test limit), offset at 0V | Offset Range | 50 Ω (ProLink): ±500 mV @ 2-100 mV/div ±4 V @ >100 mV/div -1 V/div 50 Ω (ProBus): ±750 mV @ 2-100 mV/div ±4 V @ >100 mV/div -1 V/div 1 MΩ: ±1V @ 2-140 mV/div ±10V @ 142mV-1.40V/div ±100V @ 1.42V-10V/div | Offset Accuracy | 50 Ω (ProLink): 2 mV-1 V/div, fully variable (2-9.9 mV/div via zoom) 50 Ω (ProBus): 2 mV-1 V/div, fully variable; 1 MΩ (ProBus): 2 mV-10 V/div, fully variable | DC Vertical Offset Accuracy | ±(1.5% of offset setting + 1.5% F.S. + 1 mV) (test limit) | | Horizontal System | Timebases | Internal timebase common to 4 input channels | Time/Division Range | At 80 GS/s: Real-Time Mode, 20 ps/div - 640 μs/div, depending on memory length At 40 GS/s and below: 20 ps/div-128 s/div (Real-Time Mode: 20 ps/div - 64 s/div; RIS mode: 20 ps/div - 10 ns/div, user selectable at ≦10ns/div; Roll mode: 100 ms/div up to 128 s/div, user selectable at ≧100 ms/div and ≦5 MS/s), depending on memory length | Clock Accuracy | < 1 ppm + (aging of 0.5ppm/yr from last calibration) | Sample Clock Jitter | up to 10μs Acquired Time Range: 100fsrms (Internal Timebase Reference)
up to 6.4ms Acquired Time Range: 150fsrms (Internal Timebase Reference) | Delta Time Measurement Accuracy | √2*√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) (RMS)+(clock accuracy*reading)(seconds) | Jitter Measurement Floor | √((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) secondsrms (TIE) | Jitter Between Channels | <250fsrms (TIE, typical, measured at maximum bandwidth) | Trigger and Interpolator Jitter | <0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware), | Channel-Channel Deskew Range | ±9 x time/div. setting or 25 ns max. (whichever is larger), each channel | External Timebase Reference (Input) | 10 MHz; 50 Ω impedance, applied at the rear input | External Timebase Reference (Output) | 10 MHz; 50 Ω impedance, output at the rear | | Acquisition System | Single-Shot Sample Rate/Ch | 40 GS/s on 4 Ch 80 GS/s on 2 Ch | Random Interleaved Sampling (RIS) | 200 GS/s for repetitive signals (20 ps/div to 10 ns/div) | Maximum Trigger Rate | 1,000,000 waveforms/second (in Sequence Mode, up to 4 channels) | Intersegment Time | 1 μs | | Acquisition Processing | Averaging | Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps | Enhanced Resolution (ERES) | From 8.5 to 11 bits vertical resolution | Envelope (Extrema) | Envelope, floor, or roof for up to 1 million sweeps | Interpolation | Linear or Sin x/x | | Triggering System | Modes | Normal, Auto, Single, and Stop | Sources | Any input channel, Aux, Aux/10, Line, or Fast Edge. Slope and level unique to each source (except line trigger) | Coupling Mode | DC, AC, HFRej, LFRej | Pre-trigger Delay | 0-100% of memory size (adjustable in 1% increments of 100 ns) | Post-trigger Delay | 0-10,000 divisions in real time mode, limited at slower time/div settings or in roll mode | Hold-off by Time or Events | From 2 ns up to 20 s or from 1 to 99,999,999 events | Internal Trigger Range | ±4.1 div from center | Trigger Sensitivity with Edge Trigger (1.85/2.4/2.92mm Inputs) | Not Applicable | Trigger Sensitivity with Edge Trigger ProBus Inputs | 2 div @ < 3.5 GHz, 1.5 div @ < 1.75 GHz, 1.0 div @ < 200 MHz, (for DC coupling, ≧ 10 mV/div, 50 Ω) | Trigger Sensitivity with Edge Trigger ProLink Inputs | 3 div @ < 15 GHz, 1.5 div @ < 3 GHz, 1.0 div @ < 200 MHz, (for DC, AC, LFRej coupling, ≧ 10 mV/div, 50 Ω) | External Trigger Sensitivity, (Edge Trigger) | 2 div @ < 1 GHz, 1.5 div @ < 500 MHz, 1.0 div @ < 200 MHz, (for DC coupling) | Max. Trigger Frequency, SMART Trigger | 2.0 GHz @ ≧ 10 mV/div (minimum triggerable width 200 ps) | External Trigger Input Range | Aux (±0.4 V); Aux/10 (±4 V) | | Basic Triggers | Edge | Triggers when signal meets slope (positive, negative, or either) and level condition. | Window | Triggers when signal exits a window defined by adjustable thresholds | TV-Composite Video | Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative). | | SMART Triggers | State or Edge Qualified | Triggers on any input source only if a defined state or edge occurred on another input source. Holdoff between sources is selectable by time or events. | Qualified First | In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. | Dropout | Triggers if signal drops out for longer than selected time between 1 ns and 20 s. | Pattern | Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don't care. The High and Low level can be selected independently. Triggers at start or end of the pattern. | | SMART Triggers with Exclusion Technology | Glitch | Triggers on positive or negative glitches with widths selectable as low as 200ps to 20 s, or on intermittent faults. | Width (Signal or Pattern) | Triggers on positive, negative, or both widths with widths selectable as low as 200ps to 20 s, or on intermittent faults. | Interval (Signal or Pattern) | Triggers on intervals selectable between 1 ns and 20 s. | Timeout (State/Edge Qualified) | Triggers on any source if a given state (or transition edge) has occurred on another source. Delay between sources is 1 ns to 20 s, or 1 to 99,999,999 events. | Runt | Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns. | Slew Rate | Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. | Exclusion Triggering | Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met | | Cascade (Sequence) Triggering | Capability | Arm on "A" event, then Trigger on "B" event. Or Arm on "A" event, then Qualify on "B" event, and Trigger on "C" event. | Types | Cascade A then B: Edge, Window, Pattern (Logic) Width, Glitch, Interval, Dropout, or Measurement. Measurement can be on Stage B only. Cascade A then B then C (Measurement): Edge, Window, Pattern (Logic), Width, Glitch, Interval, Dropout, or Measurement. Measurement can be on Stage C only. Cascade A then B then C: Edge, Window, Pattern (Logic) | Holdoff | Holdoff between A and B or B and C is selectable by time (1ns to 20s) or number of events. Measurement trigger selection as the last stage in a Cascade precludes a holdoff setting between the prior stage and the last stage. | | High Speed Serial Protocol Triggering | Data Rates | Option WM8Zi-6GBIT-80B-8B10B-TD: 600 Mb/s to 6.5 Gb/s, Channel 4 input only Option WM8Zi-14GBIT-80B-8B10B-TD: 600 Mb/s to 14.1 Gb/s, Channel 4 input only (Note: Channel 3 input will capture signal for triggering when oscilloscope is in 80 GS/s mode) | Pattern Length | 80 bits NRZ, eight 8b/10b symbols, 64b/66b symbol | Clock and Data Outputs | No Clock and Data Recovery outputs provided | | Low Speed Serial Protocol Triggering (Optional) | Optionally available | I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay, I2S (Audio), MIL-1553 | | Measurement Trigger | Measurement Trigger Capability | Select from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger. | | Color Waveform Display | Type | Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen | Resolution | WXGA; 1280 x 768 pixels. | Number of traces | Display a maximum of 16 traces (up to 40 with some software options). Simultaneously display channel, zoom, memory and math traces. | Grid Styles | Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y | Waveform Representation | Sample dots joined, or sample dots only | | Internal Waveform Memory | Internal Waveform Memory | 12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity. | | Integrated Second Display | Type | Supports touch screen integration of user-supplied second display with split-grid capability. (Note: touch screen driver for second display may not be a Fujitsu driver) | Resolution | Determined by display chosen by user | | LeCroy WaveStream Fast Viewing Mode | Intensity | 256 Intensity Levels, 1-100% adjustable via front panel control | Types | Select analog or color-graded | Number of Channels | up to 4 simultaneously | Max Sampling Rate | 80 GS/s | Persistence Aging | Select from 500 ms to Infinity | Waveforms/second (continuous) | up to 2500 Waveforms/second | Operation | Front panel toggle between WaveStream ON (Analog), ON (Color) and OFF | | Analog Persistence Display | Analog and Color-Graded Persistence | Variable saturation levels; stores each trace's persistence data in memory | Persistence Types | Select analog, color, or three-dimensional | Trace Selection | Activate persistence on all or any combination of traces | Persistence Aging | Select from 500 ms to infinity | Sweep Display Modes | All accumulated, or all accumulated with last trace highlighted | | High Speed Digitizer Output (Option) | Type | LeCroy LSIB | Transfer Rate | up to 325 MB/s (typical) | Output Protocol | PCI Express, Gen 1 (4 lanes utilized for data transfer) | Control Protocol | TCP/IP | Command Set | Via Windows Automation, or via LeCroy Remote Command Set | | Processor/CPU | Type | Intel Core i7-4770S Quad, 3.1 GHz (up to 3.9 GHz in Turbo mode) (or better) | Processor Memory | 8 GB standard for STD memory (20 Mpt), S-32 and M-64 memory options 16 GB standard for L-128 and VL-256 memory options Up to 32 GB optional | Operating System | Microsoft WindowsR 7 Professional Edition (64-bit) | Real Time Clock | Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks. | | Zoom Expansion Traces | Zoom Expansion Traces | Display up to 12 Zoom and 12 Math/Zoom traces | | Setup Storage | Front Panel and Instrument Status | Store to the internal hard drive, over the network, or to a USB-connected peripheral device. | | Interface | Remote Control | Via Windows Automation, or via LeCroy Remote Command Set | Network Communication Standard | VXI-11 or VICP, LXI Class C (v1.2) Compliant | GPIB Port | Supports IEEE - 488.2 | LSIB Port (optional) | Supports PCIe Gen1 x4 protocol with LeCroy supplied API | Ethernet Port | Supports 10/100/1000BaseT Ethernet interface (RJ45 port) | USB Ports | 4 rear USB 3.0 ports, 3 front panel USB 2.0 ports support Windows compatible devices | External Monitor Port | Full-size DisplayPort connnector Includes support for extended desktop operation with second monitor. | Peripheral Bus | LeCroy LBUS standard | | Auxiliary Input | Signal Types | For External Trigger Input | Coupling | 50 Ω: DC; 1 MΩ: AC, DC, GND | Max. Input Voltage | 50 Ω: 5 Vrms; 1 MΩ: 250 V (Peak AC < 10 kHz + DC) | | Auxiliary Output | Signal Types | Select from calibrator, control signals or Off | Output Signal | 500 Hz-5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0-1 V into 1 MΩ) | Control Signals | Trigger enabled, trigger out, pass/fail status, off | Connector Type | BNC, located on front | | Automatic Setup | Auto Setup | Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals | Find Vertical Scale | Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range | | General | Auto Calibration | Ensures specified DC and timing accuracy is maintained for 1 year minimum. | | Probes | Probes
| Qty. (4) ÷10 Passive Probes | Probe System | Probus and ProLink. Automatically detects and supports a variety of compatible probes | Scale Factors | Automatically or manually selected depending on probe used | Calibration Output | Cal Output: 1kHz square wave, 1Vp-p (typical), output to probe hook. | | Power Requirements | Voltage | 100-240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection, Installation Category II | Max. Power Consumption | 975 W / 975 VA | | Environmental and Safety | Temperature (Operating) | +5 °C to +40 °C | Temperature (Non-Operating) | -20 °C to +60 °C | Humidity (Operating) | 5% to 80% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C. | Humidity (Non-Operating) | 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F | Altitude (Operating) | Up to 10,000 ft. (3048 m) at or below +25 °C | Altitude (Non-Operating) | Up to 40,000 ft. (12,192 m) | Random Vibration (Operating) | 0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes | Random Vibration (Non-Operating) | 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes | Functional Shock | 20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total | | Physical Dimensions | Dimensions (HWD) | 14"H x 18.4"W x 16"D (355 x 467 x 406 mm) | Weight | 51.5 lbs. (23.4 kg) | Shipping Weight | 70.0 lbs. (31.8 kg) | | Certifications | Certifications | CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, EN61010-2-030, UL 61010-1 3rd edition, and CSA C22.2 No. 61010-1-12 | | Warranty and Service | Warranty and Service | 3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services. | |
 DDA 830 Zi-B スペック
Vertical System | Analog Bandwidth (Max) | 30 GHz | Analog Bandwidth @ 50 Ω (-3 dB) (2.4/2.92mm Inputs) | 30 GHz | Analog Bandwidth @ 50 Ω (-3 dB) (ProLink Input) | 20 GHz (≧10 mV/div) | Analog Bandwidth @ 50 Ω (-3 dB) (ProBus Input) | 3.5 GHz (≧10 mV/div) | Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input) | 500 MHz (typical, ≧2 mV/div) | Rise Time (10-90%, 50 Ω) | 15.5 ps (test limit, flatness mode) | Rise Time (20-80%, 50 Ω) | 11.5 ps (flatness mode) | Input Channels | 4 (Any combination of 20 GHz ProLink inputs or 3.5 GHz ProBus inputs), 3 (1 @ full BW, 2 with ProLink or ProBus inputs), or 2 (@ full BW) | Bandwidth Limiters | For ≦20 GHz Mode: 20 MHz, 200 MHz, 1 GHz, 4 GHz, 6 GHz, 8 GHz, 13 GHz, 16 GHz For >20 GHz Mode: 20 GHz, 25 GHz | Input Impedance | 2.92mm Inputs: 50 Ω+/-2% for ≦79 mV/div, 50 Ω+/-3% for >79 mV/div ProLink Inputs: 50 Ω+/-2% for ≦100 mV/div, 50 Ω+/-3% for >100 mV/div ProBus Inputs: 50 Ω+/-2% or 1 MΩ||16pF, 10 MΩ || 11 pF with supplied Probe | Input Coupling | 2.92 mm Inputs: 50 Ω: DC, GND ProLink Inputs - 50 Ω: DC, GND ProBus Inputs - 1 MΩ: AC, DC, GND; 50 Ω: DC, GND | Maximum Input Voltage | 2.92 mm Inputs: ±2 [email protected]≦79mV/div, [email protected]>79mV/div 50 Ω (ProLink): ±2 [email protected]≦100mV/div, [email protected]>100mV/div 50 Ω (ProBus): ±5 Vmax, 3.5 Vrms 1 MΩ (ProBus): 250 V max. (peak AC: < 10 kHz + DC) | Channel-Channel Isolation | DC to 10 GHz: 50 dB (>315:1) 10 to 15 GHz: 46 dB (>200:1) 15 to 20 GHz: 40 dB (>100:1) 20 GHz to Max BW: 30 dB (>32:1) (For any two ProLink or 2.92mm input channels, same or different v/div settings, typical) | Vertical Resolution | 8 bits; up to 11 bits with enhanced resolution (ERES) | Sensitivity | 50 Ω (2.92 mm): 10 mV-500 mV/div, fully variable 50 Ω (ProLink): 2 mV-1 V/div, fully variable (2-9.9 mV/div via zoom) 50 Ω (ProBus): 2 mV-1 V/div, fully variable 1 MΩ (ProBus): 2 mV-10 V/div, fully variable | DC Vertical Gain Accuracy (Gain Component of DC Accuracy) | ±1% F.S. (typical), offset at 0V; ±1.5% F.S. (test limit), offset at 0V | Offset Range | 50 Ω (2.92 mm): ±500 mV @ 10-79 mV/div ±4 V @ 80 mV/div -500 mV/div 50 Ω (ProLink): ±500 mV @ 2-100 mV/div ±4 V @ >100 mV/div -1 V/div 50 Ω (ProBus): ±750 mV @ 2-100 mV/div ±4 V @ >100 mV/div -1 V/div 1 MΩ: ±1V @ 2-128 mV/div ±10V @ 130mV-1.28V/div ±100V @ 1.3V-10V/div | Offset Accuracy | 50 Ω (2.92 mm): 10 mV-500 mV/div, fully variable 50 Ω (ProLink): 2 mV-1 V/div, fully variable (2-9.9 mV/div via zoom) 50 Ω (ProBus): 2 mV-1 V/div, fully variable 1 MΩ (ProBus): 2 mV-10 V/div, fully variable | DC Vertical Offset Accuracy | ±(1.5% of offset setting + 1.5% F.S. + 1 mV) (test limit) | | Horizontal System | Timebases | Internal timebase common to 4 input channels | Time/Division Range | For ≧25 GHz Mode: Real-Time Mode, 20 ps/div - 640 μs/div, depending on memory length For ≦20 GHz Mode: 20 ps/div-128 s/div (Real-Time Mode: 20 ps/div - 64 s/div; RIS mode: 20 ps/div - 10 ns/div, user selectable at ≦10ns/div; Roll mode: 100 ms/div up to 128 s/div, user selectable at ≧100 ms/div and ≦5 MS/s), depending on memory length | Clock Accuracy | < 1 ppm + (aging of 0.5ppm/yr from last calibration) | Sample Clock Jitter | up to 10μs Acquired Time Range: 100fsrms (Internal Timebase Reference)
up to 6.4ms Acquired Time Range: 150fsrms (Internal Timebase Reference) | Delta Time Measurement Accuracy | √2*√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) (RMS)+(clock accuracy*reading)(seconds) | Jitter Measurement Floor | √((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) secondsrms (TIE) | Jitter Between Channels | <250fsrms (TIE, typical, measured at maximum bandwidth) | Trigger and Interpolator Jitter | <0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware), | Channel-Channel Deskew Range | ±9 x time/div. setting or 25 ns max. (whichever is larger), each channel | External Timebase Reference (Input) | 10 MHz; 50 Ω impedance, applied at the rear input | External Timebase Reference (Output) | 10 MHz; 50 Ω impedance, output at the rear | | Acquisition System | Single-Shot Sample Rate/Ch | 40 GS/s on 4 Ch (80 GS/s on 2 Ch when operated in ≧25 GHz Mode) | Random Interleaved Sampling (RIS) | For ≧25 GHz Mode: Not Available For <25 GHz Mode: 200 GS/s for repetitive signals (20 ps/div to 10 ns/div) | Maximum Trigger Rate | 1,000,000 waveforms/second (in Sequence Mode, up to 4 channels) | Intersegment Time | 1 μs | Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments) | 128 M / 128 M / 128 M (In <20 GHz Modes, reference memory specification for DDA 813Zi-B) (1000) | Memory Options (4 Ch / 2 Ch / 1Ch) (Number of Segments) | L-128 Option: 256M / 256M / 256M (15,000) VL-256 Option: 512M / 512M / 512M (15,000) (In ≦20 GHz Modes, reference memory specification for DDA 813Zi-B) | | Acquisition Processing | Averaging | Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps | Enhanced Resolution (ERES) | From 8.5 to 11 bits vertical resolution | Envelope (Extrema) | Envelope, floor, or roof for up to 1 million sweeps | Interpolation | Linear or Sin x/x | | Triggering System | Modes | Normal, Auto, Single, and Stop | Sources | Any input channel, Aux, Aux/10, Line, or Fast Edge. Slope and level unique to each source (except line trigger) | Coupling Mode | DC, AC, HFRej, LFRej | Pre-trigger Delay | 0-100% of memory size (adjustable in 1% increments of 100 ns) | Post-trigger Delay | 0-10,000 divisions in real time mode, limited at slower time/div settings or in roll mode | Hold-off by Time or Events | From 2 ns up to 20 s or from 1 to 99,999,999 events | Internal Trigger Range | ±4.1 div from center | Trigger Sensitivity with Edge Trigger (1.85/2.4/2.92mm Inputs) | 3 div @ < 15 GHz 1.5 div @ < 3 GHz 1.0 div @ < 200 MHz (for DC coupling, ≧ 10 mV/div, 50 Ω) | Trigger Sensitivity with Edge Trigger ProBus Inputs | 2 div @ < 3.5 GHz, 1.5 div @ < 1.75 GHz, 1.0 div @ < 200 MHz, (for DC coupling, ≧ 10 mV/div, 50 Ω) | Trigger Sensitivity with Edge Trigger ProLink Inputs | 3 div @ < 15 GHz, 1.5 div @ < 3 GHz, 1.0 div @ < 200 MHz, (for DC, AC, LFRej coupling, ≧ 10 mV/div, 50 Ω) | External Trigger Sensitivity, (Edge Trigger) | 2 div @ < 1 GHz, 1.5 div @ < 500 MHz, 1.0 div @ < 200 MHz, (for DC coupling) | Max. Trigger Frequency, SMART Trigger | 2.0 GHz @ ≧ 10 mV/div (minimum triggerable width 200 ps) | External Trigger Input Range | Aux (±0.4 V); Aux/10 (±4 V) | | Basic Triggers | Edge | Triggers when signal meets slope (positive, negative, or either) and level condition. | Window | Triggers when signal exits a window defined by adjustable thresholds | TV-Composite Video | Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative). | | SMART Triggers | State or Edge Qualified | Triggers on any input source only if a defined state or edge occurred on another input source. Holdoff between sources is selectable by time or events. | Qualified First | In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. | Dropout | Triggers if signal drops out for longer than selected time between 1 ns and 20 s. | Pattern | Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don't care. The High and Low level can be selected independently. Triggers at start or end of the pattern. | | SMART Triggers with Exclusion Technology | Glitch | Triggers on positive or negative glitches with widths selectable as low as 200ps to 20 s, or on intermittent faults. | Width (Signal or Pattern) | Triggers on positive, negative, or both widths with widths selectable as low as 200ps to 20 s, or on intermittent faults. | Interval (Signal or Pattern) | Triggers on intervals selectable between 1 ns and 20 s. | Timeout (State/Edge Qualified) | Triggers on any source if a given state (or transition edge) has occurred on another source. Delay between sources is 1 ns to 20 s, or 1 to 99,999,999 events. | Runt | Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns. | Slew Rate | Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. | Exclusion Triggering | Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met | | Cascade (Sequence) Triggering | Capability | Arm on "A" event, then Trigger on "B" event. Or Arm on "A" event, then Qualify on "B" event, and Trigger on "C" event. | Types | Cascade A then B: Edge, Window, Pattern (Logic) Width, Glitch, Interval, Dropout, or Measurement. Measurement can be on Stage B only. Cascade A then B then C (Measurement): Edge, Window, Pattern (Logic), Width, Glitch, Interval, Dropout, or Measurement. Measurement can be on Stage C only. Cascade A then B then C: Edge, Window, Pattern (Logic) | Holdoff | Holdoff between A and B or B and C is selectable by time (1ns to 20s) or number of events. Measurement trigger selection as the last stage in a Cascade precludes a holdoff setting between the prior stage and the last stage. | | High Speed Serial Protocol Triggering | Data Rates | Option WM8Zi-6GBIT-80B-8B10B-TD: 600 Mb/s to 6.5 Gb/s, Channel 4 input only Option WM8Zi-14GBIT-80B-8B10B-TD: 600 Mb/s to 14.1 Gb/s, Channel 4 input only (Note: Channel 3 input will capture signal for triggering when oscilloscope is in ≧25 GHz mode) | Pattern Length | 80 bits NRZ, eight 8b/10b symbols, 64b/66b symbol | Clock and Data Outputs | No Clock and Data Recovery outputs provided | | Low Speed Serial Protocol Triggering (Optional) | Optionally available | I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay, I2S (Audio), MIL-1553 | | Measurement Trigger | Measurement Trigger Capability | Select from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger. | | Color Waveform Display | Type | Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen | Resolution | WXGA; 1280 x 768 pixels. | Number of traces | Display a maximum of 16 traces (up to 40 with some software options). Simultaneously display channel, zoom, memory and math traces. | Grid Styles | Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y | Waveform Representation | Sample dots joined, or sample dots only | | Internal Waveform Memory | Internal Waveform Memory | 12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity. | | Integrated Second Display | Type | Supports touch screen integration of user-supplied second display with split-grid capability. (Note: touch screen driver for second display may not be a Fujitsu driver) | Resolution | Determined by display chosen by user | | LeCroy WaveStream Fast Viewing Mode | Intensity | 256 Intensity Levels, 1-100% adjustable via front panel control | Types | Select analog or color-graded | Number of Channels | up to 4 simultaneously | Max Sampling Rate | 80 GS/s | Persistence Aging | Select from 500 ms to Infinity | Waveforms/second (continuous) | up to 2500 Waveforms/second | Operation | Front panel toggle between WaveStream ON (Analog), ON (Color) and OFF | | Analog Persistence Display | Analog and Color-Graded Persistence | Variable saturation levels; stores each trace's persistence data in memory | Persistence Types | Select analog, color, or three-dimensional | Trace Selection | Activate persistence on all or any combination of traces | Persistence Aging | Select from 500 ms to infinity | Sweep Display Modes | All accumulated, or all accumulated with last trace highlighted | | High Speed Digitizer Output (Option) | Type | LeCroy LSIB | Transfer Rate | up to 325 MB/s (typical) | Output Protocol | PCI Express, Gen 1 (4 lanes utilized for data transfer) | Control Protocol | TCP/IP | Command Set | Via Windows Automation, or via LeCroy Remote Command Set | | Processor/CPU | Type | Intel Core i7-4770S Quad, 3.1 GHz (up to 3.9 GHz in Turbo mode) (or better) | Processor Memory | 8 GB standard for STD memory (20 Mpt), S-32 and M-64 memory options 16 GB standard for L-128 and VL-256 memory options Up to 32 GB optional | Operating System | Microsoft WindowsR 7 Professional Edition (64-bit) | Real Time Clock | Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks. | | Zoom Expansion Traces | Zoom Expansion Traces | Display up to 12 Zoom and 12 Math/Zoom traces | | Setup Storage | Front Panel and Instrument Status | Store to the internal hard drive, over the network, or to a USB-connected peripheral device. | | Interface | Remote Control | Via Windows Automation, or via LeCroy Remote Command Set | Network Communication Standard | VXI-11 or VICP, LXI Class C (v1.2) Compliant | GPIB Port | Supports IEEE - 488.2 | LSIB Port (optional) | Supports PCIe Gen1 x4 protocol with LeCroy supplied API | Ethernet Port | Supports 10/100/1000BaseT Ethernet interface (RJ45 port) | USB Ports | 4 rear USB 3.0 ports, 3 front panel USB 2.0 ports support Windows compatible devices | External Monitor Port | Full-size DisplayPort connnector Includes support for extended desktop operation with second monitor. | Peripheral Bus | LeCroy LBUS standard | | Auxiliary Input | Signal Types | For External Trigger Input | Coupling | 50 Ω: DC; 1 MΩ: AC, DC, GND | Max. Input Voltage | 50 Ω: 5 Vrms; 1 MΩ: 250 V (Peak AC < 10 kHz + DC) | | Auxiliary Output | Signal Types | Select from calibrator, control signals or Off | Output Signal | 500 Hz-5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0-1 V into 1 MΩ) | Control Signals | Trigger enabled, trigger out, pass/fail status, off | Connector Type | BNC, located on front | | Automatic Setup | Auto Setup | Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals | Find Vertical Scale | Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range | | General | Auto Calibration | Ensures specified DC and timing accuracy is maintained for 1 year minimum. | | Probes | Probes
| Qty. (2) ÷10 Passive Probes | Probe System | Probus, ProLink, and 2.4/2.92mm. Automatically detects and supports a variety of compatible probes. | Scale Factors | Automatically or manually selected depending on probe used | Calibration Output | Cal Output: 1kHz square wave, 1Vp-p (typical), output to probe hook. | | Power Requirements | Voltage | 100-240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection, Installation Category II | Max. Power Consumption | 1025 W / 1025 VA | | Environmental and Safety | Temperature (Operating) | +5 °C to +40 °C | Temperature (Non-Operating) | -20 °C to +60 °C | Humidity (Operating) | 5% to 80% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C. | Humidity (Non-Operating) | 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F | Altitude (Operating) | Up to 10,000 ft. (3048 m) at or below +25 °C | Altitude (Non-Operating) | Up to 40,000 ft. (12,192 m) | Random Vibration (Operating) | 0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes | Random Vibration (Non-Operating) | 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes | Functional Shock | 20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total | | Physical Dimensions | Dimensions (HWD) | 14"H x 18.4"W x 16"D (355 x 467 x 406 mm) | Weight | 58 lbs. (26.4 kg) | Shipping Weight | 76.0 lbs. (34.5 kg) | | Certifications | Certifications | CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, EN61010-2-030, UL 61010-1 3rd edition, and CSA C22.2 No. 61010-1-12 | | Warranty and Service | Warranty and Service | 3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services. | |
ページトップへ

- FC/SAS/SATAなどの高速シリアルインタフェース解析機能を標準でサポート
(SDAモデルと同等)
- 複数のセクターをマルチズームで拡大して比較
- チャンネルのエミュレーションとワンタッチで設定・操作が可能な
ディスク・ドライブトリガ
- ヘッドのイコライゼーション、チャンネルのエミュレーション、SAMヒストグラム
- セクター単位のパラメータ解析に適したセグメント化メモリ
ディスク・ドライブ解析のための総合ソリューション
パフォーマンスの最大化
レクロイのディスク・ドライブ・アナライザ(DDA)は、製品開発期間の短縮や、
既存ドライブの障害解析の効率化に役立つ、HDD開発エンジニアのための統合ツールです。
DDA 8Zi-BシリーズはレクロイのDDAの伝統を受け継いだ統合ソリューションであり、
強力なディスク・ドライブ解析ツールセットを備えています。
高速で複雑なドライブ信号の波形の捕捉、表示、解析を高精度かつ迅速に行うことができます。
設計上の問題解決やメディアの特性分析を行うときにはデータの複数のセクターや
複雑なトラックの捕捉が重要になるため、データ・ストレージ・アプリケーションではメモリが
大量に消費されます。DDA 8Zi-Bシリーズでは、X-Stream IIアーキテクチャを通じて、
ディスク・ドライブ信号の高速かつ正確な測定と解析が可能です。
メモリ・オプションVLを使用すると、1チャンネルあたりのメモリを最大256Mポイント
(2チャンネル構成では1チャンネルあたり最大512Mポイント)に拡張できます。 入力として50Ω_または1MΩ_を選択できます。
36Mポイントの波形メモリが標準装備され、4つのチャンネル上で40 Gs/秒の高速捕捉がサポートされるため、
複数のドライブ・セクターを同時に捕捉することができます。
Long Memory and Flexibility in Finding Problems
ヘッド信号を捕捉した後、フロント・パネルからその信号を即座にズーム(QuickZoom)することができます。ドライブ信号はDDAによって自動的にコピー・拡張されます。個々のセクターを検証するには、縦方向または横方向のスクロールを行います。マルチズーム機能を使用すると、ヘッド信号の別々の領域を最高8個まで表示できます(各ズームは別々の色で示されます)。ディスク・ドライブ・パラメータを使用すると、特定の領域におけるS/N比やパルス幅変動の特性を分析できます。障害分析を行うエンジニアは、理想的な基準波形およびパネル・セットアップの保存と呼出しを通じて、問題のあるドライブと正常なドライブを比較することができます。最高40
GS/秒の速度で動作するA/Dコンバータは、高速化が進む、リードチャネルの測定をより高精度に測定することができます。独自に開発したスクリプトをDA上で実行すると、捕捉信号を特定のチャンネルやメディアに適合したフィルタを通して表示できます。このようなユーザ独自のスクリプトは、MATLAB、VisualBasic、Excel、その他のフォーマットを利用することができます。
ディアに適合したフィルタを通して表示できます。このようなユーザ独自のスクリプトは、MATLAB、VisualBasic、Excel、その他のフォーマットを利用することができます。
トリガとシーケンス・パフォーマンス
DDAのディスク・トリガでは、信号内で一連のイベントを設定し、それらのイベントに対して、トリガをかけることができます。たとえば、インデックス信号を基準として、そのトラックの全セクターの情報を収拾することができます。DDA
8Zi-Bシリーズにはロングメモリを搭載することができるため、1サンプルあたり最高25psの分解能で、より多くのセクターを捕捉できます。DDA
8Zi-Bシリーズでは、最高15,000個のセクターのデータを収集できます。カスケード・トリガ機能により、3つもしくは4つのイベントを使用して、複雑なトリガが可能になります。これにより、インデックス信号のエッジでトリガ・レディ⇒リード・ゲート信号⇒ヘッド信号でトリガをかけることができるため、作業効率が大幅に向上します。
ページトップへ
使いやすいグラフィカル・インタフェース
DDAメニューを押すだけで、ディスク・ドライブ・アナライザの各種機能にアクセスすることができます。
フロント・パネルには使いやすいコントロールがあるほか、ユーザー・コマンドをすばやく呼び出せるコンテキスト対応型の直感的なGUIが用意されています。
必要な機能が最適な場所に効率的に配置されています。
DDA 8Zi-Bシリーズでは、ディスク・ドライブ処理の正確なデバッグと解析に必要な機能にいつでも簡単にアクセスすることができます。
DDA 8 Zi-Bの機能と特長:
- FC/SAS/SATAなどの高速シリアルインタフェースの解析
- 28種類のカスタム・パラメータ
- 個別ドライブ・トリガ
─ セクター
─ サーボ・ゲート:
─ 読み取りゲート・トリガ
- 高度なドライブ解析ツール
─ ヘッド・フィルタ/
イコライザー・エミュレーション
─ チャンネル・エミュレーション
─ SAMヒストグラム
─ SAM値のプロット
─ アナログ比較
ページトップへ
クリックで詳細表示されます
ミックスド・シグナル・ソリューション
HDA125-18-LBUS
12.5GS/s高速ミックスド・シグナル・オプション
(18チャンネルQuickLinkリードセット、LBUS接続) |
HDA125-09-LBUS
12.5GS/s高速ミックスド・シグナル・オプション
(9チャンネルQuickLinkリードセット、LBUS接続) |
MS-500
最高500MHz、18ch、帯域ミックスド・シグナル・オプション |
MS-500-36
最高250MHz帯域、36ch、ミックスド・シグナル・オプション |
MS-250
最高250MHz帯域、18ch、ミックスド・シグナル・オプション |
メモリ・オプション
WM8Zi-S-32
32 Mpt/Ch (4 channel operation) Memory Option for WaveMaster 8 Zi-A. |
WM8Zi-M-64
64 Mpt/Ch (4 channel operation) Memory Option for WaveMaster 8 Zi-A. |
WM8Zi-L-128
128 Mpt/Ch (4 channel operation) Memory Option for WaveMaster 8 Zi-A. Incl. 16 GB CPU RAM standard. |
WM8Zi-VL-256
256 Mpt/Ch (4 channel operation) Memory Option for WaveMaster 8 Zi-A. Incl. 16 GB CPU RAM standard. |
SDA8Zi-M-64
64 Mpt/Ch (4 channel operation) Memory Option for SDA 8 Zi-A. |
DDA8Zi-M-64
64 Mpt/Ch (4 channel operation) Memory Option for DDA 8 Zi-A. |
SDA8Zi-L-128
128 Mpt/Ch (4 channel operation) Memory Option for SDA 8 Zi-A. Incl. 16 GB CPU RAM standard. |
DDA8Zi-L-128
128 Mpt/Ch (4 channel operation) Memory Option for DDA 8 Zi-A. Incl. 16 GB CPU RAM standa |
SDA8Zi-VL-256
256 Mpt/Ch (4 channel operation) Memory Option for SDA 8 Zi-A. Incl. 16 GB CPU RAM standard. |
DDA8Zi-VL-256
256 Mpt/Ch (4 channel operation) Memory Option for DDA 8 Zi-A. Incl. 16 GB CPU RAM standard. |
サンプリング速度オプション
WM8Zi-2X80GS
80 GS/s on 2ch Sampling Rate Option for WaveMaster/SDA/DDA 8 Zi and 8Zi-A (not available for 820Zi, 825Zi/Zi-A, 830Zi/Zi-A, 9x30Zi-A, 845Zi-A or 9x45Zi-A). Includes two separate external interleaving devices with storage case. |
ハードウエア・オプション
WM8Zi-500GB-RHD-02
Additional 500 GB Hard Drive for WM8Zi or 8Zi-A. Includes Windows 7 OS, LeCroy oscilloscope software and critical scope operational file duplicates. |
WM8Zi-8-UPG-32GBRAM
8 GB to 32 GB CPU RAM Upgrade Option |
帯域アップグレード (WaveMaster/SDA/DDA 8Ziシリーズ)
WM8ZI-4-RK-6GHZ
4GHzから6GHzにアップグレード |
WM8ZI-4-RK-8GHZ
4GHzから8GHzにアップグレード |
WM8ZI-4-RK-13GHZ
4GHzから13GHzにアップグレード |
WM8ZI-4-RK-16GHZ
4GHzから16GHzにアップグレード |
WM8ZI-4-RK-20GHZ
4GHzから20GHzにアップグレード |
WM8ZI-4-RK-25GHZ
4GHzから25GHzにアップグレード |
WM8ZI-4-RK-30GHZ
4GHzから30GHzにアップグレード |
WM8ZI-6-RK-8GHZ
6GHzから8GHzにアップグレード |
WM8ZI-6-RK-13GHZ
6GHzから13GHzにアップグレード |
WM8ZI-6-RK-16GHZ
6GHzから16GHzにアップグレード |
WM8ZI-6-RK-20GHZ
6GHzから20GHzにアップグレード |
WM8ZI-6-RK-25GHZ
6GHzから25GHzにアップグレード |
WM8ZI-6-RK-30GHZ
6GHzから30GHzにアップグレード |
WM8ZI-8-RK-13GHZ
8GHzから13GHzにアップグレード |
WM8ZI-8-RK-16GHZ
8GHzから16GHzにアップグレード |
WM8ZI-8-RK-20GHZ
8GHzから20GHzにアップグレード |
WM8ZI-8-RK-25GHZ
8GHzから25GHzにアップグレード |
WM8ZI-8-RK-30GHZ
8GHzから30GHzにアップグレード |
WM8ZI-13-RK-16GHZ
13GHzから16GHzにアップグレード |
WM8ZI-13-RK-20GHZ
13GHzから20GHzにアップグレード |
WM8ZI-13-RK-25GHZ
13GHzから25GHzにアップグレード |
WM8ZI-13-RK-30GHZ
13GHzから30GHzにアップグレード |
WM8ZI-16-RK-20GHZ
16GHzから20GHzにアップグレード |
WM8ZI-16-RK-25GHZ
16GHzから25GHzにアップグレード |
WM8ZI-16-RK-30GHZ
16GHzから30GHzにアップグレード |
WM8ZI-20-RK-25GHZ
20GHzから25GHzにアップグレード |
WM8ZI-20-RK-30GHZ
20GHzから30GHzにアップグレード |
WM8ZI-25-RK-30GHZ
25GHzから30GHzにアップグレード |
帯域アップグレード (WaveMaster/SDA/DDA 8Zi-Aシリーズ)
WM8ZI-A-4-RK-6GHZ
4GHzから6GHzにアップグレード |
WM8ZI-A-4-RK-8GHZ
4GHzから8GHzにアップグレード |
WM8ZI-A-4-RK-13GHZ
4GHzから13GHzにアップグレード |
WM8ZI-A-4-RK-16GHZ
4GHzから16GHzにアップグレード |
WM8ZI-A-4-RK-20GHZ
4GHzから20GHzにアップグレード |
WM8ZI-A-4-RK-25GHZ
4GHzから25GHzにアップグレード |
WM8ZI-A-4-RK-30GHZ
4GHzから30GHzにアップグレード |
WM8ZI-A-6-RK-8GHZ
6GHzから8GHzにアップグレード |
WM8ZI-A-6-RK-13GHZ
6GHzから13GHzにアップグレード |
WM8ZI-A-6-RK-16GHZ
6GHzから16GHzにアップグレード |
WM8ZI-A-6-RK-20GHZ
6GHzから20GHzにアップグレード |
WM8ZI-A-6-RK-25GHZ
6GHzから25GHzにアップグレード |
WM8ZI-A-6-RK-30GHZ
6GHzから30GHzにアップグレード |
WM8ZI-A-8-RK-13GHZ
8GHzから13GHzにアップグレード |
WM8ZI-A-8-RK-16GHZ
8GHzから16GHzにアップグレード |
WM8ZI-A-8-RK-20GHZ
8GHzから20GHzにアップグレード |
WM8ZI-A-8-RK-25GHZ
8GHzから25GHzにアップグレード |
WM8ZI-A-8-RK-30GHZ
8GHzから30GHzにアップグレード |
WM8ZI-A-13-RK-16GHZ
13GHzから16GHzにアップグレード |
WM8ZI-A-13-RK-20GHZ
13GHzから20GHzにアップグレード |
WM8ZI-A-13-RK-25GHZ
13GHzから25GHzにアップグレード |
WM8ZI-A-13-RK-30GHZ
13GHzから30GHzにアップグレード |
WM8ZI-A-16-RK-20GHZ
16GHzから20GHzにアップグレード |
WM8ZI-A-16-RK-25GHZ
16GHzから25GHzにアップグレード |
WM8ZI-A-16-RK-30GHZ
16GHzから30GHzにアップグレード |
WM8ZI-A-20-RK-25GHZ
20GHzから25GHzにアップグレード |
WM8ZI-A-20-RK-30GHZ
20GHzから30GHzにアップグレード |
WM8ZI-A-25-RK-30GHZ
25GHzから30GHzにアップグレード |
帯域アップグレード (WaveMaster/SDA/DDA 8Zi-Bシリーズ)
WM8ZI-B-4-RK-6GHZ
4GHzから6GHzにアップグレード |
WM8ZI-B-4-RK-8GHZ
4GHzから8GHzにアップグレード |
WM8ZI-B-4-RK-13GHZ
4GHzから13GHzにアップグレード |
WM8ZI-B-4-RK-16GHZ
4GHzから16GHzにアップグレード |
WM8ZI-B-4-RK-20GHZ
4GHzから20GHzにアップグレード |
WM8ZI-B-4-RK-25GHZ
4GHzから25GHzにアップグレード |
WM8ZI-B-4-RK-30GHZ
4GHzから30GHzにアップグレード |
WM8ZI-B-6-RK-8GHZ
6GHzから8GHzにアップグレード |
WM8ZI-B-6-RK-13GHZ
6GHzから13GHzにアップグレード |
WM8ZI-B-6-RK-16GHZ
6GHzから16GHzにアップグレード |
WM8ZI-B-6-RK-20GHZ
6GHzから20GHzにアップグレード |
WM8ZI-B-6-RK-25GHZ
6GHzから25GHzにアップグレード |
WM8ZI-B-6-RK-30GHZ
6GHzから30GHzにアップグレード |
WM8ZI-B-8-RK-13GHZ
8GHzから13GHzにアップグレード |
WM8ZI-B-8-RK-16GHZ
8GHzから16GHzにアップグレード |
WM8ZI-B-8-RK-20GHZ
8GHzから20GHzにアップグレード |
WM8ZI-B-8-RK-25GHZ
8GHzから25GHzにアップグレード |
WM8ZI-B-8-RK-30GHZ
8GHzから30GHzにアップグレード |
WM8ZI-B-13-RK-16GHZ
13GHzから16GHzにアップグレード |
WM8ZI-B-13-RK-20GHZ
13GHzから20GHzにアップグレード |
WM8ZI-B-13-RK-25GHZ
13GHzから25GHzにアップグレード |
WM8ZI-B-13-RK-30GHZ
13GHzから30GHzにアップグレード |
WM8ZI-B-16-RK-20GHZ
16GHzから20GHzにアップグレード |
WM8ZI-B-16-RK-25GHZ
16GHzから25GHzにアップグレード |
WM8ZI-B-16-RK-30GHZ
16GHzから30GHzにアップグレード |
WM8ZI-B-20-RK-25GHZ
20GHzから25GHzにアップグレード |
WM8ZI-B-20-RK-30GHZ
20GHzから30GHzにアップグレード |
WM8ZI-B-25-RK-30GHZ
25GHzから30GHzにアップグレード |
リモートコントロール/ネットワーク・オプション
GPIB-2
IEEE 488 GPIB Interface |
電源解析
トリガ/デコード・パッケージ
WM8Zi-1553 TD
MIL-STD-1553用トリガ・デコード・オプション |
WM8Zi-1553 TDME
MIL-STD-1553 Trigger, Decode, Measure/Graph, and Eye Diagram Option |
WM8Zi-64b66b D
64b/66b シンボル・デコード |
WM8Zi-6GBIT-80B-SYMBOL-TD
80ビット NRZ、8b/10b、64b/66b 6.5 Gbps
シリアルトリガ・オプション |
WM8Zi-8B10B D
8b10bトリガ/デコード・オプション |
WM8Zi-ARINC429BUS DME SYMBOLIC
ARINC 429 Bus Symbolic Decode, Measure/Graph, and Eye Diagram Option |
WM8Zi-ARINC429BUS DSYMBOLIC
ARINC 429 Bus Symbolic Decode option |
WM8Zi-MDIObus D
MDIOデコード・オプション |
WM8Zi-SPMIbus D
SPMIデコード・オプション |
WM8Zi-AudioBus TD
AudioBus-I2S トリガ・デコード・オプション |
WM8Zi-AudioBus TDG
AudioBusトリガ/デコード/グラフ・パッケージ |
WM8Zi-CANbus TD
CAN用トリガ/デコード・オプション |
WM8Zi-CANbus TDME
CAN FD Trigger, Decode, Measure/Graph, and Eye Diagram Option |
WM8Zi-CAN FDbus TD
CAN FD用トリガ/デコード・オプション |
WM8Zi-CAN FDbus TDME
CAN FD Trigger, Decode, Measure/Graph, and Eye Diagram Option |
WM8Zi-CAN FDbus TDME SYMBOLIC
CAN FD Symbolic Trigger, Decode, and Measure/Graph, and Eye Diagram Option |
WM8Zi-DigRFV4bus D
DigRF V4デコード・オプション |
WM8Zi-DigRF3Gbus D
DigRF 3Gデコード・オプション |
WM8Zi-DPHYbus D
MIPI D-PHYデコード・オプション |
WM8Zi-DPHYbus DP
MIPI D-PHYデコード物理層試験パッケージ |
WM8Zi-EMB TD
Bundle: Includes I2C, SPI, UART-RS232 Trigger and Decode Options |
WM8Zi-EMB TDME
Bundle: Incl. I2C, SPI, UART-RS232 Trigger, Decode, Measure/Graph, and Eye Diagram Opt. |
WM8Zi-ENETbus D
イーサネット・デコード・オプション |
WM8Zi-FCbus D
Fiber Channel用デコード・オプション |
WM8Zi-FlexrayBus TD
FlexRay用トリガ/デコード・オプション |
WM8Zi-FlexRaybus TDMP
FlexRay Trigger, Decode, Measure/Graph and Physical Layer Option |
WM8Zi-I2Cbus TD
I2C用トリガ/デコード・オプション |
WM8Zi-I2CBUS TDME
I2C Trigger, Decode, Measure/Graph, and Eye Diagram Option |
WM8Zi-LINbus TD
LIN用トリガ/デコード・オプション |
WM8Zi-LINBUS TDME
LIN Trigger, Decode, Measure/Graph, and Eye Diagram Option |
WM8Zi-Manchesterbus D
Manchesterbus用デコード・オプション |
WM8Zi-MPHYbus D
MIPI M-PHYデコード・オプション |
WM8Zi-MPHYbus DP
MIPI M-PHYデコード・オプション |
WM8Zi-MSO-EMB TD
Bundle: MS-500-36 with I2C, SPI, UART and RS-232 Trigger and Decodes |
WM8Zi-MSO-EMB TDME
Bundle: MS-500-36 with I2C, SPI, UART-RS-232 Trig, Decode, Measure/Graph and Eye Opt. |
WM8Zi-NRZbus D
NRZ用デコード・オプション |
WM8Zi-PCIebus D
PCI Expressトリガ・デコード・オプション |
WM8Zi-ProtoBus MAG
PROTObus MAG シリアル・デバッグ・ツールキット |
WM8Zi-ProtoSync
デコード情報とプロトコル・アナライザ同期オプション |
WM8Zi-PROTOSYNC-BT
プロトコル解析オプション(Bit Tracer機能付) |
WM8Zi-SASbus D
SAS用デコード・オプション |
WM8Zi-SATAbus TD
SATA用トリガ・デコード・オプション |
WM8Zi-SENTbus D
SENTデコード・オプション |
WM8Zi-SpaceWirebus D
SpaceWireデコード・オプション |
WM8Zi-SPIbus TD
SPI用トリガ/デコード・オプション |
WM8Zi-SPIBUS TDME
SPI Trigger, Decode, Measure/Graph, and Eye Diagram Option |
WM8Zi-UART-RS232bus TD
UART-RS232用トリガ/デコード・オプション |
WM8Zi-UART-RS232BUS TDME
UART-RS232 Trigger, Decode, Measure/Graph, and Eye Diagram Option |
WM8Zi-UNIPRObus D
UniProデコード・オプション |
WM8Zi-UPG-MPHY-UNIPRObus D
MPHY to UniPro Decoder Software Upgrade MPHY REQUIRED |
WM8Zi-USB2-HSICbus D
USB 2.0 HSICデコード・オプション |
WM8Zi-USB2bus TD
USB 2.0トリガ・デコード・オプション |
WM8Zi-USB2bus TDME
USB 2.0 Trigger, Decode, Measure/Graph, and Eye Diagram Option |
WM8Zi-USB3bus D
USB3.0.デコード・オプション |
ジッタ解析パッケージ
デジタル・フィルタ・パッケージ
コンプライアンス・テスト・パッケージ
QPHY-10GBase-KR
10Gbase-KRコンプライアンス・テスト・パッケージ |
QPHY-10GBASE-T
10Gbase-Tコンプライアンス・テスト・パッケージ |
QPHY-56G-PAM4
56G PAM4コンプライアンス・テスト・パッケージ |
QPHY-BroadR-Reach
BroadR-Reachコンプライアンス・テスト・パッケージ |
QPHY-MOST150
MOST150oコンプライアンス・テスト・パッケージ |
QPHY-MOST50
MOST50eコンプライアンス・テスト・パッケージ |
QPHY-MIPI-DPHY
MIPIコンプライアンス・テスト・オプション |
QPHY-PCIe
PCI Express(Gen1,2)コンプライアンス・テスト・パッケージ |
QPHY-PCIe3-Tx-Rx
PCI Express(Gen3)コンプライアンス・テスト・パッケージ |
WM8Zi-DDR2-TOOLKIT
DDRデバッグツールキット(対応規格DDR2, LPDDR2) |
WM8Zi-DDR3-TOOLKIT
DDRデバッグツールキット(対応規格DDR2, DDR3, DDR3L, LPDDR2, LPDDR3) |
WM8ZI-DDR4-TOOLKIT
DDRデバッグツールキット(対応規格DDR2, DDR3, DDR3L, DDR4, LPDDR2, LPDDR3, LPDDR4) |
WM8ZI-DDR5-TOOLKIT
DDRデバッグツールキット(対応規格DDR2, DDR3, DDR3L, DDR4,DDR5, LPDDR2, LPDDR3, LPDDR4,LPDDR5) |
QPHY-DDR2
DDR2テスト・オプション |
QPHY-DDR3
DDR3テスト・オプション |
QPHY-DDR4
DD4コンプライアンス・テスト・パッケージ |
QPHY-DisplayPort
DisplayPortコンプライアンス・テスト・パッケージ |
QPHY-HDMI
HDMIコンプライアンス・テスト・パッケージ |
QPHY-ENET
イーサネット・テスト・オプション |
QPHY-LPDDR2
LPDDR2テスト・オプション |
QPHY-SAS2
SASコンプライアンス・テスト・パッケージ |
QPHY-SAS3
SAS3コンプライアンス・テスト・パッケージ |
QPHY-SATA-TSG-RSG
SATAコンプライアンス・テスト・パッケージ |
QPHY-USB
USBテスト・オプション |
QPHY-USB3-Tx-Rx
USB3.0コンプライアンス・テスト・パッケージ |
QPHY-USB3.1-Tx-Rx
USB3.1コンプライアンス・テスト・パッケージ |
QPHY-UWB
UWBコンプライアンス・テスト・パッケージ |
ENET-2ADA-BNCSMA
Adapter Set- 2 BNC/M to SMA/F |
ENET-2CAB-SMA018
Cable Set- 2 SMA-SMA 18 inches |
ENET-2CAB-SMA036
Cable Set- 2 SMA-SMA 36 inches |
シリアル・データ解析
WM8Zi-SDAIII-CompleteLinQ
Bundle - Multi-Lane SDA LinQ Framewk, incl. Eye, Jitter, Noise, Xtalk Meas, w/EyeDrII & VirtualProbe |
SDA8Zi-CompleteLinQ
Bundle - Multi-Lane SDA LinQ Framewk, incl. Eye, Jitter, Noise, Xtalk Meas, w/EyeDrII & VirtualProbe |
DDA8Zi-CompleteLinQ
Bundle - Multi-Lane SDA LinQ Framewk, incl. Eye, Jitter, Noise, Xtalk Meas, w/EyeDrII & VirtualProbe |
WM8Zi-SDAIII-CrossLinQ
Multi-Lane Serial Data Analysis LinQ Framework, Eye, Jitter, Noise and Crosstalk Measurements |
SDA8Zi-CrossLinQ
Multi-Lane Serial Data Analysis LinQ Framework, Eye, Jitter, Noise and Crosstalk Measurements |
DDA8Zi-CrossLinQ
Multi-Lane Serial Data Analysis LinQ Framework, Eye, Jitter, Noise and Crosstalk Measurements |
WM8Zi-SDAIII-Crosstalk
Single-Lane Serial Data Analysis Framework, Eye, Jitter, Noise and Crosstalk Measurements |
DDA8Zi-Crosstalk
Single-Lane Serial Data Analysis Framework, Eye, Jitter, Noise and Crosstalk Measurements |
SDA8Zi-Crosstalk
Single-Lane Serial Data Analysis Framework, Eye, Jitter, Noise and Crosstalk Measurements |
WM8Zi-SDAIII-LinQ
Multi-Lane Serial Data Analysis LinQ Framework, Eye and Jitter Measurements |
SDA8Zi-LinQ
Multi-Lane Serial Data Analysis LinQ Framework, Eye and Jitter Measurements |
DDA8Zi-LinQ
Multi-Lane Serial Data Analysis LinQ Framework, Eye and Jitter Measurements |
WM8Zi-VIRTUALPROBE
Advanced De-embedding, Emulation and Virtual Probing Toolkit |
WM8Zi-CBL-DE-EMBED
ケーブル・デエンベデッド |
WM8Zi-SDM
シリアルデータ解析パッケージ |
WM8Zi-EYEDRII
Signal Integrity Toolkit - Channel & Fixture De-embedding/Emulation, Tx/Rx Equalization |
WM8Zi-EYEDRII-VP
Bundle - EyeDrII and VirtualProbe Toolkits |
erial Data Analysis, Eye, Jitter and Noise Measurements
WM8ZI-PAM4
PAM4信号解析オプション
|
その他、汎用ソフトウエア
その他オプション
オシロスコープチャンネル同期オプション
データストレージ解析
ミックスド・シグナル・アクセサリ
PK400-1
大型グリッパ・プローブ・セット − 2.54mmピン・ピッチ用、色分け導線が付いた10個のプローブからなるセット |
PK400-2
中型グリッパ・プローブ・セット − 1.0mmピン・ピッチ用、色分け導線が付いた10個のプローブからなるセット |
PK400-3
小型グリッパ・プローブ・セット − 0.2mmピン・ピッチ用、色分け導線が付いた10個のプローブからなるセット |
MSO-MICTOR
36ピンMictorインタフェース・ケーブル |
MSO-3M
18ピン3Mインタフェース・ケーブル (3Mパーツ番号2520-6002とともに使用)
|
テスト・フィクスチャ
Serial Trigger Hardware
WM8Zi-14GBIT-80B-SYMBOL-TD
80-bit NRZ, 8b/10b, and 64b/66b 14.1 Gbps Serial Trigger option for WaveMaster 8 Zi-A and DDA 8 Zi-A |
WM8ZI-6GBIT-80B-SYMBOL-TD
80-bit NRZ, 8b/10b, and 64b/66b 6.5Gbps Serial Trigger option for WaveMaster 8 Zi-A and DDA 8 Zi-A |
クリックで詳細表示されます
プローブ・アダプタ
アクティブ・プローブ
ZS1500
1.5GHz ハイインピーダンス・アクティブ・プローブ |
ZS1000
1GHz ハイインピーダンス・アクティブ・プローブ |
ZS1500
1.5GHz ハイインピーダンス・アクティブ・プローブ |
ZS1000
1GHz ハイインピーダンス・アクティブ・プローブ |
電流プローブ
CP030/CP030A
電流プローブ、DC〜50MHz 30A (DC)、 50A(ピーク) 、CP030Aは最高感度1mA/div |
CP031/CP031A
電流プローブ、DC〜100MHz 30A (DC)、 50A(ピーク) 、CP031Aは最高感度1mA/div |
CP150
電流プローブ、DC〜10MHz 150A (DC)、500A(ピーク) |
CP500
電流プローブ、DC〜2MHz 500A (DC)、700A(ピーク) |
DCS025
電流プローブ用スキュー調整ジグ |
CA10
サードパーティ製電流測定デバイス用アダプタ |
CA10-QUADPAK
サードパーティ製電流測定デバイス用アダプタ(4個セット) |
差動アンプ
DA1855A
100MHz高精度・オフセット機能付き差動アンプ 1ch仕様 (ProBus対応) |
DXC100A
DAシリーズ用ペア・プローブ:250MHz* 10:1/100:1 1MΩ 10.5pF |
DXC200
DAシリーズ用ペア・プローブ:50MHz 1:1 30pF |
DXC-5100
DAシリーズ用ペア・プローブ:250MHz(DA1855A使用時は100MHz) 100:1 2.75pF 最大入力電圧 2,500VDC+Peak |
DA101
10:1 1MΩ受動アッテネータ (DXC5100用) |
DA1855A-PR2
100MHz高精度・オフセット機能付き差動アンプ 2ch仕様 (ProBus対応) |
DA1855A-PR2-RM
100MHz高精度・オフセット機能付き差動アンプ 2ch仕様 (ProBus対応) ラックマウント仕様 (後付不可) |
差動プローブ
差動プローブ (4-6 GHz)
D410-A-PB2 4 GHz ProBus2 Differential Probe with Dx10-SI Solder-In Tip (Qty. 1), Dx10-QC Quick Connect (Qty. 1) and Dx10-SP Square Pin (Qty. 1) | D420-A-PB2 4 GHz ProBus2 Differential Probe with Dx20-SI Solder-In Tip (Qty. 1), Dx20-QC Quick Connect (Qty. 1) and Dx20-SP Square Pin (Qty. 1) | D610-A-PL 6 GHz ProLink Differential Probe with Dx10-SI Solder-In Tip (Qty. 1), Dx10-QC Quick Connect (Qty. 1) and Dx10-SP Square Pin (Qty. 1) | D620-A-PL 6 GHz ProLink Differential Probe with Dx20-SI Solder-In Tip (Qty. 1), Dx20-QC Quick Connect (Qty. 1) and Dx20-SP Square Pin (Qty. 1) | D400A-AT-PB2 4 GHz ProBus2 Differential Probe with Adjustable Tip | D600A-AT-PL 6 GHz ProLink Differential Probe with Adjustable Tip | LPA-PBUS2 ProLink to ProBus2 Adapter | LPA-PBUS2 ProLink to ProBus2 Adapter | LPA-PBUS2 ProLink to ProBus2 Adapter | Dx10-HiTemp WaveLink Temperature Extension cables for Dx10. Includes 1 set of matched 30" high temperature cables, 1 solder tip lead set | Dx20-HiTemp WaveLink Temperature Extension cables for Dx20. Includes 1 set of matched 30" high temperature cables, 1 solder tip lead set | Dx10-SI Replacement Solder tip lead set for D410/D610 | Dx20-SI Replacement Solder tip lead set for D420/D620 | Dx10-QL-3SI QuickLink Solder-In starter pack for use with Dx10 amplifier | Dx20-QL-3SI QuickLink Solder-In starter pack for use with Dx20 amplifier | TF-DSQ Probe Deskew and Calibration Test Fixture Limited Availability | D410-A-CCNIST NIST Calibration for D410-A. Includes test data. | D420-A-CCNIST NIST Calibration for D420-A. Includes test data. | D610-A-CCNIST NIST Calibration for D610-A. Includes test data. | D620-A-CCNIST NIST Calibration for D620-A. Includes test data. |
差動プローブ (8-13 GHz)
Dxx30-PT-KIT WaveLink Dxx30-PT (up to 10 GHz rating) Adjustable Positioner Tip Kit. For use with Dxx30 amplifiers | Dxx30-SI Replacement Dxx30-SI 8-13 GHz Solder-In Lead with Qty. 5 Spare Resistors. | Dxx30-QL-3SI QuickLink Solder-In starter pack for use with Dxx30 amplifier. Includes one QuickLink Adapter and three QL-SI tips. | D830-CCNIST NIST Calibration for D830. Includes test data. | D1330-CCNIST NIST Calibration for D1330. Includes test data. | D830-PL 8 GHz ProLink Differential Probe with Dxx30-SI Solder-In Tip (Qty. 2) and Dxx30-SP Square Pin (Qty. 1) | D1330-PL 13 GHz ProLink Differential Probe with Dxx30-SI Solder-In Tip (Qty. 2) and Dxx30-SP Square Pin (Qty. 1) | TF-DSQ Probe Deskew and Calibration Test Fixture Limited Availability |
差動プローブ (16-25 GHz)
D1605-A-PLA 16 GHz ProLink Differential Probe with Dxx05-SI Solder-In Tip (Qty. 2) |
Dxx05-PTKIT WaveLink Dxx05-PT (up to 22 GHz rating) Adj. Positioner Tip Kit.For use with Dxx05-A amplifiers. | DXX05-SI Replacement Dxx05-SI 13-25 GHz Solder-In Lead with Qty. 5 Spare Resistors. | LPA-2.92 ProLink to 2.92mm Adapter with Probe Power and Communication Pass Through | D1605-A-CCNIST NIST Calibration for D1605-A. Includes test data. | D2005-A-CCNIST NIST Calibration for D2005-A. Includes test data. | D2505-A-CCNIST NIST Calibration for D2505-A. Includes test data. | D2005-A-PLA 20 GHz ProLink Differential Probe with Dxx05-SI Solder-In Tip (Qty. 2) | D2505-A-2.92MM 25 GHz ProLink Differential Probe with Dxx05-SI Solder-In Tip (Qty. 2) | TF-DSQ Probe Deskew and Calibration Test Fixture Limited Availability |
高電圧差動プローブ
高電圧プローブ
HVP120
400MHz、50MΩ、1kVrms-6kV(過渡)、高電圧プローブ |
PPE4KV
高電圧プローブ、耐圧4kV、100:1、400MHz帯域、50MΩ、<6pF、2mケーブル |
PPE5KV
高電圧プローブ、耐圧4kV、100:1、400MHz帯域、50MΩ、<6pF、2mケーブル |
PPE6KV
高電圧プローブ、耐圧6kV、1000:1、400MHz帯域、50MΩ、<6pF、2mケーブル、 |
O/E変換器
OE425
5GHz 500-870nm O/Eコンバータ (ProBus入力用) |
OE455
3.5GHz 950-1630nm O/Eコンバータ (ProBus入力用) |
OE525
5GHz 500-870nm O/Eコンバータ (ProLink入力用) |
OE555
3.5GHz 950-1630nm O/Eコンバータ (ProLink入力用) |
Probe Parts and Kits
Dx10-HiTEMP
WaveLink Temperature Extension cables for Dx10. Includes 1 set of matched 30" high temperature cables, 1 solder tip lead set |
Dx10-SI-HiTEMP
Replacement Solder tip leadset for use with D410/D610 and temperature extension cables |
Dx20-HiTEMP
WaveLink Temperature Extension cables for Dx20. Includes 1 set of matched 30" high temperature cables, 1 solder tip lead set |
Dx20-SI-HiTEMP
Replacement Solder tip leadset for use with D420/620 and temperature extension cables |
Dxx0-Cable-HiTemp
Replacement 30" matched cable set for use with HiTemp Solder tip leadset |
LPA-K-A
Pro-Link to K/2.92mm Adapter |
LPA-K-KIT-A
Kit of Qty. 4 Pro-Link to K/2.92mm Adapter |
LPA-SMA-A
Pro-Link to SMA Adapter, new style |
LPA-SMA-KIT-A
Kit of Pro-Link to SMA Adapter, new style |
OE695G-REFCAL
OE695G Reference Cal (1ch) |
PK006
SMT Probing Accessories for AP020, PP002, and PP006 Surface Mount Technology Accessories |
パッシブ・プローブ
PP066
7.5 GHz low capacitance Passive Probe, 500/1K Ohms |
ページトップへ
|
|
|