高精度12ビット、8ch オシロスコープ
WaveRunner 8000HDシリーズ

(日本語字幕付きデモビデオ) 唯一の8チャンネル、12ビット、2GHzオシロスコープ より多くのチャンネル数、より柔軟な計測 HD4096®テクノロジで常時12ビット より多くの波形メモリが必要ではありませんか？─最長5Gポイントの波形メモリ デモビデオ

基本仕様

モデルごとスペック詳細（モデル名をクリックで詳細表示されます）

WaveRunner 8038HD　スペック

Vertical - Analog Channels
Analog Bandwidth (Max)	350 MHz
Analog Bandwidth @ 50 Ω (-3 dB) (ProBus Input)	350 MHz (≧1 mV/div)
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input)	350 MHz
Rise Time (10-90%, 50 Ω)	1 ns
Rise Time (20-80%, 50 Ω)	750 ps
Input Channels	8
Vertical Resolution	12 bits; up to 15 bits with enhanced resolution (ERES)
Effective Number of Bits (ENOB)	8.9 bits
Vertical Noise Floor (1 mV/div)	95 µVrms
Vertical Noise Floor (2 mV/div)	95 µVrms
Vertical Noise Floor (5 mV/div)	100 µVrms
Vertical Noise Floor (10 mV/div)	115 µVrms
Vertical Noise Floor (20 mV/div)	130 µVrms
Vertical Noise Floor (50 mV/div)	185 µVrms
Vertical Noise Floor (100 mV/div)	285 µVrms
Vertical Noise Floor (200 mV/div)	1.30 mVrms
Vertical Noise Floor (500 mV/div)	1.85 mVrms
Vertical Noise Floor (1 V/div)	2.95 mVrms
Sensitivity	50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	±(0.5%) FS, offset at 0 V
Channel-Channel Isolation	DC-200 MHz: 70 dB (>3000:1), 200-350 MHz: 60 dB (>1000:1) (For any two input channels, same V/div settings, typical)
Offset Range	50 Ω ±1.6 V @ 1 mV - 4.95 mV/div ±4 V @ 5 mV - 9.9 mV/div ±8 V @ 10 mV - 19.8 mV/div ±10 V @ 20 mV - 1 V/div 1 MΩ ±1.6 V @ 1 mV - 4.95 mV/div ±4 V @ 5 mV - 9.9 mV/div ±8 V @ 10 mV - 19.8 mV/div ±16 V @ 20 mV - 100 mV/div ±80 V @ 102 mV - 198 mV/div ±160 V @ 200 mV - 1 V/div ±400 V @ 1.02 V - 10 V/div
DC Vertical Offset Accuracy	±(0.5% of offset setting + 0.5% FS + 1mV)
Maximum Input Voltage	50 Ω: 5 Vrms, 1 MΩ: 400 V max (DC + Peak AC ≤ 10 kHz)
Input Coupling	1 MΩ: AC, DC, GND; 50 Ω: DC, GND
Input Impedance	50 Ω+/-2% or 1 MΩ||19pF, 10 MΩ || 10 pF
Bandwidth Limiters	20MHz, 200MHz
Rescaling	Length: meters, inches, feet, yards, miles; Mass: grams, slugs; Temperature: celsius, fahrenheit, kelvin; Angle: radian, arcdegr, arcmin, arcsec, cycles, revolutions, turns; Velocity: m/s, in/s, ft/s, yd/s, miles/s; Acceleration: m/s2, in/s2, ft/s2, g0; Volume: liters, cubic meters, cubic inches, cubic feet, cubic yards; Force (Weight): newton, grain, ounce, pound; Pressure: pascal, bar, atmosphere (technical), atmosphere (standard), torr, psi; Electrical: volts, amps, watts, volt-amperes, volt-amperes reactive, farad, coulomb, ohm, siemen, volt/meter, coulomb/m2, farad/meter, siemen/meter, power factor; Magnetic: weber, tesla, henry, amp/meter, henry/meter; Energy: joule, Btu, calorie; Rotating Machine: radian/second, frequency, revolution/second, revolution/minute, N?m, lb-ft, lb-in, oz-in, watt, horsepower; Other: %.
Horizontal - Analog Channels
Timebases	Internal timebase common to 8 input channels
Acquisition Modes	Real-time, Roll, Sequence
Time/Division Range	100 ps/div - 5 ks/div with standard memory (up to 10 ks/div with 500MPT memory, 25 ks/div with 1000MPT memory, 50 ks/div with 2000MPT memory, 100 ks/div with 5000MPT memory); Roll Mode available at ≥ 100 ms/div and ≤ 5 MS/s
Clock Accuracy	+/-1 ppm + 1 ppm/year from calibration
Sample Clock Jitter	up to 10µs Acquired Time Range: 80 fsrms (Internal Timebase Reference) up to 10ms Acquired Time Range: 150 fsrms (Internal Timebase Reference)
Delta Time Measurement Accuracy	\sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds)
Jitter Measurement Floor	\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)}
Channel-Channel Deskew Range	±9 x time/div. setting, 100 ms max., each channel
External Timebase Reference (Input)	10MHz +/-25ppm at 0 to 10dBm into 50 Ohms
External Timebase Reference (Output)	10MHz, 5.0 dBm +/-2.5 dBm, sinewave synchronized to reference being used (internal or external reference)
Acquisition - Analog Channels
Sample Rate (Single-shot)	10 GS/s on 8 Ch with Enhanced Sample Rate
Memory Length (4 Ch / 2 Ch / 1Ch) (Number of Segments)	50M/100M/200M (65,536)
Memory Length Options (4 Ch / 2 Ch / 1Ch) (Number of Segments)	WR8KHD-500MPT Option: 125M / 250M / 500M (65,535) WR8KHD-1000MPT Option: 250M / 500M / 1000M (65,535) WR8KHD-2000MPT Option: 500M / 1000M / 2000M (65,535) WR8KHD-5000MPT Option: 1250M / 2500M / 5000M (65,535) Maximum analysis memory: 500 Mpts per channel
Intersegment Time	1.5 µs
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps (Waveforms of ≤500Mpts)
Enhanced Resolution (ERES)	From 12.5 to 15 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps (Waveforms of ≤500Mpts)
Interpolation	Linear or Sin x/x (2 pt and 5 pt) (Waveforms of ≤500Mpts)
Vertical, Horizontal, Acquisition - Digital Channels
Maximum Input Frequency	500 MHz
Minimum Detectable Pulse Width	1 ns
Input Channels	16 Digital channels (with WR8KHD-MSO option)
Input Impedance (Flying Leads)	100 kΩ || 5 pF
Input Dynamic Range	± 20V
Maximum Input Voltage	±30V Peak
Maximum Input Voltage Swing	400mV
Threshold Groupings	Pod 2: D15 - D8, Pod 1: D7 - D0
Threshold Selections	TTL, ECL, CMOS (2.5 V, 3.3 V, 5 V), PECL, LVDS or User Defined
Threshold Accuracy	±(3% of threshold setting + 100mV)
User Defined Threshold Range	±10 V in 20 mV steps
User Defined Hysteresis Range	100 mV to 1.4 V in 100 mV steps
Sample Rate	2.5GS/s
Record Length	Standard: 50 Mpts Any memory option: 500 Mpts
Channel-to-Channel Skew	350 ps
Triggering System
Modes	Acquisition of ≤500Mpts: Normal, Auto, Single, and Stop Acquisition of >500Mpts: Single
Sources	Any input channel, Ext, Ext/10, or Line; slope and level unique to each source (except line trigger)
Coupling	DC, AC, HFRej, LFRej
Pre-trigger Delay	0-100% of memory size
Post-trigger Delay	No limitation
Hold-off	From 2 ns up to 20 s or from 1 to 99,999,999 events
Trigger and Interpolator Jitter	≤ 2.5 psrms (typical) <0.1 ps RMS (typical, software assisted)
Internal Trigger Level Range	±4.1 div from center (typical)
External Trigger Level Range	Ext (±0.4 V); Ext/10 (±4 V)
Maximum Trigger Rate	650,000 waveforms/second (in Sequence Mode, up to 8 channels)
Trigger Sensitivity with Edge Trigger ProBus Inputs	1.5 div @ < 350 MHz 1 div @ < 200 MHz 0.9 div @ < 10 MHz (DC, AC, and LFRej coupling, ≥ 2 mV/div, 50 Ω)
Trigger Sensitivity with Edge Trigger (Aux Input)	1.5 div @ < 350 MHz 1 div @ < 200 MHz 0.9 div @ < 10 MHz (DC, AC, and LFRej coupling)
Max. Trigger Frequency, SMART Trigger	350 MHz
Trigger Types
Edge	Triggers when signal meets slope (positive, negative, or either) and level condition.
Width	Triggers on positive or negative glitches with selectable widths. minimum width 750ps, Maximum Width: 20s
Glitch	Triggers on positive or negative glitches with selectable widths. minimum width 750ps, Maximum Width: 20s
Window	Triggers when signal exits a window defined by adjustable thresholds
Pattern	Logic combination (AND, NAND, OR, NOR) of up to 9 inputs (8 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
Runt	Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
Slew Rate	Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
Interval	Triggers on intervals selectable between 1 ns and 20 s.
Dropout	Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
Measurement Trigger	Select from a large number of measurement parameters. Trigger on a measurement value with qualified limits.
Multi-Stage: Qualified (Timeout or State/Edge Qualified)	Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels).
Triggers with Exclusion Technology	Glitch, Width, Interval, Runt, Slew Rate - Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
Multi-Stage: Qualified First	In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels).
TriggerScan	A Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially.
Low Speed Serial Protocol Trigger (Optional)
Supported Protocols	I2C, I3C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, SENT, MIL-STD-1553, AudioBus (I2S, LJ, RJ, TDM), USB1.x/2.0, SPMI
Measurement Tools
Measurement Functionality	Display up to 12 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state.
Measurement Parameters - Horizontal + Jitter	Cycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min
Measurement Parameters - Vertical	Amplitude, Base, [email protected], Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top.
Measurement Parameters - Pulse	Area, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%)
Measurement Parameters - Statistical (on Histograms)	Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total)
Math Tools
Math Functionality	Display up to 12 math functions traces (F1-F12). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math.
Math Operators - Basic Math	Average (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+).
Math Operators - Digital (incl. with MSO models/options)	Digital AND, Digital DFlipFlop, Digital NAND, Digital NOR, Digital NOT, Digital OR, Digital XOR
Math Operators - Filters	Enhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x.
Math Operators - Frequency Analysis	FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows.
Math Operators - Functions	Absolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity).
Math Operators - Other	Segment, Sparse
Measurement and Math Integration
Measurement and Math Integration	Histograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma)
Pass/Fail Testing
Pass/Fail Testing	Display up to 12 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value <. ≤, =, >, ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook.
Display System
Size	Color 15.6" widescreen capacitive touch screen
Resolution	1920 x 1080 pixels
Number of traces	Display a maximum of 40 traces. Simultaneously display channel, zoom, memory, and math.
Grid Styles	Auto, Single, Dual, Triplex, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Triad, Quattro, Twelve, Sixteen, Twenty. Supports Normal Display Mode (1 grid style, selectable) or Q-Scape Display Mode (4 different tabs, each with individually selectable grid styles). Q-Scape tabbed displays may be viewed in Single, Dual, or Mosaic mode.
Waveform Representation	Sample dots joined, or sample dots only
Persistence Display
Analog and Color-Graded Persistence	Waveforms of ≤500Mpts: Variable saturation levels; stores each trace’s persistence data in memory
Persistence Types	Waveforms of ≤500Mpts: Select analog, color, or three-dimensional
Trace Selection	Waveforms of ≤500Mpts: Activate persistence on all or any combination of traces
Persistence Aging	Waveforms of ≤500Mpts: Select from 500 ms to infinity
Sweep Display Modes	Waveforms of ≤500Mpts: All accumulated, or all accumulated with last trace highlighted
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 12 Zoom and 12 Math/Zoom traces
Internal Waveform Memory
Internal Waveform Memory	12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
Setup Storage
Front Panel and Instrument Status	Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
Automatic Setup
Auto Setup	Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale	Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
Calibration
Calibration Stability	Calibration ensured within +/-5°C operating temperature. Manual calibration may be invoked if outside this temperature range.
Processor/CPU
Type	Intel® Core i5-6500 Quad Core, 3.2 GHz (or better)
Processor Memory	16 GB standard for standard memory with 32 GB optional. 32 GB standard for any memory option.
Operating System	Microsoft Windows® 10
Oscilloscope Operating Software	Teledyne LeCroy MAUI™ with OneTouch
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Connectivity
Ethernet Port	2 x 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Host Ports	4 side USB 3.1 Gen1 ports, 2 front USB 3.1 Gen1 ports
USB Device Port	1 port - USBTMC over USB 3.1 Gen1
GPIB Port (optional)	Supports IEEE - 488.2 (External)
External Monitor Port	1 x DisplayPort, supports up to 4096x2304 @ 24 Hz 1 x HDMI, supports up to 4096x2304 @ 60 Hz
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Compatible
Auxiliary Input
Signal Types	For external trigger input
Coupling	50 Ω: DC; 1 MΩ: AC, DC, GND
Max. Input Voltage	50 Ω 5V RMS, +/- 10V Peak 1 MΩ 400 V max (Peak DC+AC)
Auxiliary Output
Signal Types	Select from output signal, control signals, off
Output Signal	500 Hz-5 MHz square wave or DC level; 3.3 V +/- 10% into 1 MΩ
Control Signals	Trigger enabled, trigger out, pass/fail status, off
Connector Type	BNC, located on rear panel
Probes
Probes	Qty. (4) ÷10 Passive Probes
Probe System	ProBus. Automatically detects and supports a variety of compatible probes
Scale Factors	Automatically or manually selected depending on probe used
Calibration Output	Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 500 Hz to 1 MHz square wave; 50 mV to 1.0V.
Power Requirements
Voltage	100 - 240 VAC ±10% at 47 - 63 Hz 100 - 120 VAC ±10% at 380 - 420 Hz Automatic AC Voltage Selection
Nominal Power Consumption	400 W / 400 VA
Max. Power Consumption	500 W / 500 VA (with all PC peripherals and active probes connected to 8 channels)
Environmental
Temperature (Operating)	+5 °C to +40 °C
Temperature (Non-Operating)	-20 °C to +60 °C
Humidity (Operating)	5% to 90% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +30 °C
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.31 grms 5 Hz to 500 Hz, 20 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Size and Weight
Dimensions (HWD)	13.6”H x 17.5”W x 7.7”D (345 mm x 445 mm x 196 mm)
Weight	24.4 lbs (11.1 kg)
Shipping Weight	37 lbs (16.8 kg)
Certifications
CE Certification UL and cUL Listing	CE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No. 61010-1-12
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.

WaveRunner 8058HD　スペック

Vertical - Analog Channels
Analog Bandwidth (Max)	500 MHz
Analog Bandwidth @ 50 Ω (-3 dB) (ProBus Input)	500 MHz (≥1 mV/div)
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input)	500 MHz
Rise Time (10-90%, 50 Ω)	700 ps
Rise Time (20-80%, 50 Ω)	525 ps
Input Channels	8
Vertical Resolution	12 bits; up to 15 bits with enhanced resolution (ERES)
Effective Number of Bits (ENOB)	8.8 bits
Vertical Noise Floor (1 mV/div)	100 µVrms
Vertical Noise Floor (2 mV/div)	100 µVrms
Vertical Noise Floor (5 mV/div)	105 µVrms
Vertical Noise Floor (10 mV/div)	125 µVrms
Vertical Noise Floor (20 mV/div)	145 µVrms
Vertical Noise Floor (50 mV/div)	200 µVrms
Vertical Noise Floor (100 mV/div)	310 mVrms
Vertical Noise Floor (200 mV/div)	1.45 mVrms
Vertical Noise Floor (500 mV/div)	2.00 mVrms
Vertical Noise Floor (1 V/div)	3.15 mVrms
Sensitivity	50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	±(0.5%) FS, offset at 0 V
Channel-Channel Isolation	DC-200 MHz: 70 dB (>3000:1), 200-500 MHz: 60 dB (>1000:1) (For any two input channels, same V/div settings, typical)
Offset Range	50 Ω ±1.6 V @ 1 mV - 4.95 mV/div ±4 V @ 5 mV - 9.9 mV/div ±8 V @ 10 mV - 19.8 mV/div ±10 V @ 20 mV - 1 V/div 1 MΩ ±1.6 V @ 1 mV - 4.95 mV/div ±4 V @ 5 mV - 9.9 mV/div ±8 V @ 10 mV - 19.8 mV/div ±16 V @ 20 mV - 100 mV/div ±80 V @ 102 mV - 198 mV/div ±160 V @ 200 mV - 1 V/div ±400 V @ 1.02 V - 10 V/div
DC Vertical Offset Accuracy	±(0.5% of offset setting + 0.5% FS + 1mV)
Maximum Input Voltage	50 Ω: 5 Vrms, 1 MΩ: 400 V max (DC + Peak AC ≤ 10 kHz)
Input Coupling	1 MΩ: AC, DC, GND; 50 Ω: DC, GND
Input Impedance	50 Ω+/-2% or 1 MΩ||19pF, 10 MΩ || 10 pF
Bandwidth Limiters	20MHz, 200MHz, 350 MHz
Rescaling	Length: meters, inches, feet, yards, miles; Mass: grams, slugs; Temperature: celsius, fahrenheit, kelvin; Angle: radian, arcdegr, arcmin, arcsec, cycles, revolutions, turns; Velocity: m/s, in/s, ft/s, yd/s, miles/s; Acceleration: m/s2, in/s2, ft/s2, g0; Volume: liters, cubic meters, cubic inches, cubic feet, cubic yards; Force (Weight): newton, grain, ounce, pound; Pressure: pascal, bar, atmosphere (technical), atmosphere (standard), torr, psi; Electrical: volts, amps, watts, volt-amperes, volt-amperes reactive, farad, coulomb, ohm, siemen, volt/meter, coulomb/m2, farad/meter, siemen/meter, power factor; Magnetic: weber, tesla, henry, amp/meter, henry/meter; Energy: joule, Btu, calorie; Rotating Machine: radian/second, frequency, revolution/second, revolution/minute, N?m, lb-ft, lb-in, oz-in, watt, horsepower; Other: %.
Horizontal - Analog Channels
Timebases	Internal timebase common to 8 input channels
Acquisition Modes	Real-time, Roll, Sequence
Time/Division Range	100 ps/div - 5 ks/div with standard memory (up to 10 ks/div with 500MPT memory, 25 ks/div with 1000MPT memory, 50 ks/div with 2000MPT memory, 100 ks/div with 5000MPT memory); Roll Mode available at ≥ 100 ms/div and ≤ 5 MS/s
Clock Accuracy	+/-1 ppm + 1 ppm/year from calibration
Sample Clock Jitter	up to 10µs Acquired Time Range: 80 fsrms (Internal Timebase Reference) up to 10ms Acquired Time Range: 150 fsrms (Internal Timebase Reference)
Delta Time Measurement Accuracy	\sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds)
Jitter Measurement Floor	\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)}
Channel-Channel Deskew Range	±9 x time/div. setting, 100 ms max., each channel
External Timebase Reference (Input)	10MHz +/-25ppm at 0 to 10dBm into 50 Ohms
External Timebase Reference (Output)	10MHz, 5.0 dBm +/-2.5 dBm, sinewave synchronized to reference being used (internal or external reference)
Acquisition - Analog Channels
Sample Rate (Single-shot)	10 GS/s on 8 Ch with Enhanced Sample Rate
Memory Length (4 Ch / 2 Ch / 1Ch) (Number of Segments)	50M/100M/200M (65,536)
Memory Length Options (4 Ch / 2 Ch / 1Ch) (Number of Segments)	WR8KHD-500MPT Option: 125M / 250M / 500M (65,535) WR8KHD-1000MPT Option: 250M / 500M / 1000M (65,535) WR8KHD-2000MPT Option: 500M / 1000M / 2000M (65,535) WR8KHD-5000MPT Option: 1250M / 2500M / 5000M (65,535) Maximum analysis memory: 500 Mpts per channel
Intersegment Time	1.5 µs
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps (Waveforms of ≤500Mpts)
Enhanced Resolution (ERES)	From 12.5 to 15 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps (Waveforms of ≤500Mpts)
Interpolation	Linear or Sin x/x (2 pt and 5 pt) (Waveforms of ≤500Mpts)
Vertical, Horizontal, Acquisition - Digital Channels
Maximum Input Frequency	500 MHz
Minimum Detectable Pulse Width	1 ns
Input Channels	16 Digital channels (with WR8KHD-MSO option)
Input Impedance (Flying Leads)	100 kΩ || 5 pF
Input Dynamic Range	± 20V
Maximum Input Voltage	±30V Peak
Maximum Input Voltage Swing	400mV
Threshold Groupings	Pod 2: D15 - D8, Pod 1: D7 - D0
Threshold Selections	TTL, ECL, CMOS (2.5 V, 3.3 V, 5 V), PECL, LVDS or User Defined
Threshold Accuracy	±(3% of threshold setting + 100mV)
User Defined Threshold Range	±10 V in 20 mV steps
User Defined Hysteresis Range	100 mV to 1.4 V in 100 mV steps
Sample Rate	2.5GS/s
Record Length	Standard: 50 Mpts Any memory option: 500 Mpts
Channel-to-Channel Skew	350 ps
Triggering System
Modes	Acquisition of ≤500Mpts: Normal, Auto, Single, and Stop Acquisition of >500Mpts: Single
Sources	Any input channel, Ext, Ext/10, or Line; slope and level unique to each source (except line trigger)
Coupling	DC, AC, HFRej, LFRej
Pre-trigger Delay	0-100% of memory size
Post-trigger Delay	No limitation
Hold-off	From 2 ns up to 20 s or from 1 to 99,999,999 events
Trigger and Interpolator Jitter	≤ 2.5 psrms (typical) <0.1 ps RMS (typical, software assisted)
Internal Trigger Level Range	±4.1 div from center (typical)
External Trigger Level Range	Ext (±0.4 V); Ext/10 (±4 V)
Maximum Trigger Rate	650,000 waveforms/second (in Sequence Mode, up to 8 channels)
Trigger Sensitivity with Edge Trigger ProBus Inputs	1.5 div @ < 500 MHz 1 div @ < 200 MHz 0.9 div @ < 10 MHz (DC, AC, and LFRej coupling, ≥ 2 mV/div, 50 Ω)
Trigger Sensitivity with Edge Trigger (Aux Input)	1.5 div @ < 500 MHz 1 div @ < 200 MHz 0.9 div @ < 10 MHz (DC, AC, and LFRej coupling)
Max. Trigger Frequency, SMART Trigger	500 MHz
Trigger Types
Edge	Triggers when signal meets slope (positive, negative, or either) and level condition.
Width	Triggers on positive or negative glitches with selectable widths. minimum width 750ps, Maximum Width: 20s
Glitch	Triggers on positive or negative glitches with selectable widths. minimum width 750ps, Maximum Width: 20s
Window	Triggers when signal exits a window defined by adjustable thresholds
Pattern	Logic combination (AND, NAND, OR, NOR) of up to 9 inputs (8 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
Runt	Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
Slew Rate	Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
Interval	Triggers on intervals selectable between 1 ns and 20 s.
Dropout	Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
Measurement Trigger	Select from a large number of measurement parameters. Trigger on a measurement value with qualified limits.
Multi-Stage: Qualified (Timeout or State/Edge Qualified)	Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels).
Triggers with Exclusion Technology	Glitch, Width, Interval, Runt, Slew Rate - Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
Multi-Stage: Qualified First	In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels).
TriggerScan	A Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially.
Low Speed Serial Protocol Trigger (Optional)
Supported Protocols	I2C, I3C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, SENT, MIL-STD-1553, AudioBus (I2S, LJ, RJ, TDM), USB1.x/2.0, SPMI
Measurement Tools
Measurement Functionality	Display up to 12 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state.
Measurement Parameters - Horizontal + Jitter	Cycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min
Measurement Parameters - Vertical	Amplitude, Base, [email protected], Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top.
Measurement Parameters - Pulse	Area, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%)
Measurement Parameters - Statistical (on Histograms)	Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total)
Math Tools
Math Functionality	Display up to 12 math functions traces (F1-F12). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math.
Math Operators - Basic Math	Average (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+).
Math Operators - Digital (incl. with MSO models/options)	Digital AND, Digital DFlipFlop, Digital NAND, Digital NOR, Digital NOT, Digital OR, Digital XOR
Math Operators - Filters	Enhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x.
Math Operators - Frequency Analysis	FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows.
Math Operators - Functions	Absolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity).
Math Operators - Other	Segment, Sparse
Measurement and Math Integration
Measurement and Math Integration	Histograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma)
Pass/Fail Testing
Pass/Fail Testing	Display up to 12 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value <. ≤, =, >, ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook.
Display System
Size	Color 15.6" widescreen capacitive touch screen
Resolution	1920 x 1080 pixels
Number of traces	Display a maximum of 40 traces. Simultaneously display channel, zoom, memory, and math.
Grid Styles	Auto, Single, Dual, Triplex, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Triad, Quattro, Twelve, Sixteen, Twenty. Supports Normal Display Mode (1 grid style, selectable) or Q-Scape Display Mode (4 different tabs, each with individually selectable grid styles). Q-Scape tabbed displays may be viewed in Single, Dual, or Mosaic mode.
Waveform Representation	Sample dots joined, or sample dots only
Persistence Display
Analog and Color-Graded Persistence	Waveforms of ≤500Mpts: Variable saturation levels; stores each trace’s persistence data in memory
Persistence Types	Waveforms of ≤500Mpts: Select analog, color, or three-dimensional
Trace Selection	Waveforms of ≤500Mpts: Activate persistence on all or any combination of traces
Persistence Aging	Waveforms of ≤500Mpts: Select from 500 ms to infinity
Sweep Display Modes	Waveforms of ≤500Mpts: All accumulated, or all accumulated with last trace highlighted
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 12 Zoom and 12 Math/Zoom traces
Internal Waveform Memory
Internal Waveform Memory	12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
Setup Storage
Front Panel and Instrument Status	Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
Automatic Setup
Auto Setup	Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale	Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
Calibration
Calibration Stability	Calibration ensured within +/-5°C operating temperature. Manual calibration may be invoked if outside this temperature range.
Processor/CPU
Type	Intel® Core i5-6500 Quad Core, 3.2 GHz (or better)
Processor Memory	16 GB standard for standard memory with 32 GB optional. 32 GB standard for any memory option.
Operating System	Microsoft Windows® 10
Oscilloscope Operating Software	Teledyne LeCroy MAUI™ with OneTouch
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Connectivity
Ethernet Port	2 x 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Host Ports	4 side USB 3.1 Gen1 ports, 2 front USB 3.1 Gen1 ports
USB Device Port	1 port - USBTMC over USB 3.1 Gen1
GPIB Port (optional)	Supports IEEE - 488.2 (External)
External Monitor Port	1 x DisplayPort, supports up to 4096x2304 @ 24 Hz 1 x HDMI, supports up to 4096x2304 @ 60 Hz
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Compatible
Auxiliary Input
Signal Types	For external trigger input
Coupling	50 Ω: DC; 1 MΩ: AC, DC, GND
Max. Input Voltage	50 Ω 5V RMS, +/- 10V Peak 1 MΩ 400 V max (Peak DC+AC)
Auxiliary Output
Signal Types	Select from output signal, control signals, off
Output Signal	500 Hz-5 MHz square wave or DC level; 3.3 V +/- 10% into 1 MΩ
Control Signals	Trigger enabled, trigger out, pass/fail status, off
Connector Type	BNC, located on rear panel
Probes
Probes	Qty. (4) ÷10 Passive Probes
Probe System	ProBus. Automatically detects and supports a variety of compatible probes
Scale Factors	Automatically or manually selected depending on probe used
Calibration Output	Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 500 Hz to 1 MHz square wave; 50 mV to 1.0V.
Power Requirements
Voltage	100 - 240 VAC ±10% at 47 - 63 Hz 100 - 120 VAC ±10% at 380 - 420 Hz Automatic AC Voltage Selection
Nominal Power Consumption	400 W / 400 VA
Max. Power Consumption	500 W / 500 VA (with all PC peripherals and active probes connected to 8 channels)
Environmental
Temperature (Operating)	+5 °C to +40 °C
Temperature (Non-Operating)	-20 °C to +60 °C
Humidity (Operating)	5% to 90% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +30 °C
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.31 grms 5 Hz to 500 Hz, 20 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Size and Weight
Dimensions (HWD)	13.6”H x 17.5”W x 7.7”D (345 mm x 445 mm x 196 mm)
Weight	24.4 lbs (11.1 kg)
Shipping Weight	37 lbs (16.8 kg)
Certifications
CE Certification UL and cUL Listing	CE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No. 61010-1-12
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.

WaveRunner 8108HD　スペック

Vertical - Analog Channels
Analog Bandwidth (Max)	1 GHz
Analog Bandwidth @ 50 Ω (-3 dB) (ProBus Input)	1 GHz (≥1 mV/div)
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input)	500 MHz
Rise Time (10-90%, 50 Ω)	400 ps
Rise Time (20-80%, 50 Ω)	300 ps
Input Channels	8
Vertical Resolution	12 bits; up to 15 bits with enhanced resolution (ERES)
Effective Number of Bits (ENOB)	8.6 bits
Vertical Noise Floor (1 mV/div)	130 µVrms
Vertical Noise Floor (2 mV/div)	130 µVrms
Vertical Noise Floor (5 mV/div)	135 µVrms
Vertical Noise Floor (10 mV/div)	155 µVrms
Vertical Noise Floor (20 mV/div)	180 µVrms
Vertical Noise Floor (50 mV/div)	250 µVrms
Vertical Noise Floor (100 mV/div)	390 mVrms
Vertical Noise Floor (200 mV/div)	1.80 mVrms
Vertical Noise Floor (500 mV/div)	2.50 mVrms
Vertical Noise Floor (1 V/div)	4.00 mVrms
Sensitivity	50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	±(0.5%) FS, offset at 0 V
Channel-Channel Isolation	DC-200 MHz: 70 dB (>3000:1), 200-500 MHz: 60 dB (>1000:1), 500 MHz - 1 GHz: 50 dB (>300:1) (For any two input channels, same V/div settings, typical)
Offset Range	50 Ω ±1.6 V @ 1 mV - 4.95 mV/div ±4 V @ 5 mV - 9.9 mV/div ±8 V @ 10 mV - 19.8 mV/div ±10 V @ 20 mV - 1 V/div 1 MΩ ±1.6 V @ 1 mV - 4.95 mV/div ±4 V @ 5 mV - 9.9 mV/div ±8 V @ 10 mV - 19.8 mV/div ±16 V @ 20 mV - 100 mV/div ±80 V @ 102 mV - 198 mV/div ±160 V @ 200 mV - 1 V/div ±400 V @ 1.02 V - 10 V/div
DC Vertical Offset Accuracy	±(0.5% of offset setting + 0.5% FS + 1mV)
Maximum Input Voltage	50 Ω: 5 Vrms, 1 MΩ: 400 V max (DC + Peak AC ≤ 10 kHz)
Input Coupling	1 MΩ: AC, DC, GND; 50 Ω: DC, GND
Input Impedance	50 Ω+/-2% or 1 MΩ||19pF, 10 MΩ || 10 pF
Bandwidth Limiters	20MHz, 200MHz, 350 MHz, 500 MHz
Rescaling	Length: meters, inches, feet, yards, miles; Mass: grams, slugs; Temperature: celsius, fahrenheit, kelvin; Angle: radian, arcdegr, arcmin, arcsec, cycles, revolutions, turns; Velocity: m/s, in/s, ft/s, yd/s, miles/s; Acceleration: m/s2, in/s2, ft/s2, g0; Volume: liters, cubic meters, cubic inches, cubic feet, cubic yards; Force (Weight): newton, grain, ounce, pound; Pressure: pascal, bar, atmosphere (technical), atmosphere (standard), torr, psi; Electrical: volts, amps, watts, volt-amperes, volt-amperes reactive, farad, coulomb, ohm, siemen, volt/meter, coulomb/m2, farad/meter, siemen/meter, power factor; Magnetic: weber, tesla, henry, amp/meter, henry/meter; Energy: joule, Btu, calorie; Rotating Machine: radian/second, frequency, revolution/second, revolution/minute, N?m, lb-ft, lb-in, oz-in, watt, horsepower; Other: %.
Horizontal - Analog Channels
Timebases	Internal timebase common to 8 input channels
Acquisition Modes	Real-time, Roll, Sequence
Time/Division Range	100 ps/div - 5 ks/div with standard memory (up to 10 ks/div with 500MPT memory, 25 ks/div with 1000MPT memory, 50 ks/div with 2000MPT memory, 100 ks/div with 5000MPT memory); Roll Mode available at ≥ 100 ms/div and ≤ 5 MS/s
Clock Accuracy	+/-1 ppm + 1 ppm/year from calibration
Sample Clock Jitter	up to 10µs Acquired Time Range: 80 fsrms (Internal Timebase Reference) up to 10ms Acquired Time Range: 150 fsrms (Internal Timebase Reference)
Delta Time Measurement Accuracy	\sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds)
Jitter Measurement Floor	\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)}
Channel-Channel Deskew Range	±9 x time/div. setting, 100 ms max., each channel
External Timebase Reference (Input)	10MHz +/-25ppm at 0 to 10dBm into 50 Ohms
External Timebase Reference (Output)	10MHz, 5.0 dBm +/-2.5 dBm, sinewave synchronized to reference being used (internal or external reference)
Acquisition - Analog Channels
Sample Rate (Single-shot)	10 GS/s on 8 Ch with Enhanced Sample Rate
Memory Length (4 Ch / 2 Ch / 1Ch) (Number of Segments)	50M/100M/200M (65,536)
Memory Length Options (4 Ch / 2 Ch / 1Ch) (Number of Segments)	WR8KHD-500MPT Option: 125M / 250M / 500M (65,535) WR8KHD-1000MPT Option: 250M / 500M / 1000M (65,535) WR8KHD-2000MPT Option: 500M / 1000M / 2000M (65,535) WR8KHD-5000MPT Option: 1250M / 2500M / 5000M (65,535) Maximum analysis memory: 500 Mpts per channel
Intersegment Time	1.5 µs
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps (Waveforms of ≤500Mpts)
Enhanced Resolution (ERES)	From 12.5 to 15 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps (Waveforms of ≤500Mpts)
Interpolation	Linear or Sin x/x (2 pt and 5 pt) (Waveforms of ≤500Mpts)
Vertical, Horizontal, Acquisition - Digital Channels
Maximum Input Frequency	500 MHz
Minimum Detectable Pulse Width	1 ns
Input Channels	16 Digital channels (with WR8KHD-MSO option)
Input Impedance (Flying Leads)	100 kΩ || 5 pF
Input Dynamic Range	± 20V
Maximum Input Voltage	±30V Peak
Maximum Input Voltage Swing	400mV
Threshold Groupings	Pod 2: D15 - D8, Pod 1: D7 - D0
Threshold Selections	TTL, ECL, CMOS (2.5 V, 3.3 V, 5 V), PECL, LVDS or User Defined
Threshold Accuracy	±(3% of threshold setting + 100mV)
User Defined Threshold Range	±10 V in 20 mV steps
User Defined Hysteresis Range	100 mV to 1.4 V in 100 mV steps
Sample Rate	2.5GS/s
Record Length	Standard: 50 Mpts Any memory option: 500 Mpts
Channel-to-Channel Skew	350 ps
Triggering System
Modes	Acquisition of ≤500Mpts: Normal, Auto, Single, and Stop Acquisition of >500Mpts: Single
Sources	Any input channel, Ext, Ext/10, or Line; slope and level unique to each source (except line trigger)
Coupling	DC, AC, HFRej, LFRej
Pre-trigger Delay	0-100% of memory size
Post-trigger Delay	No limitation
Hold-off	From 2 ns up to 20 s or from 1 to 99,999,999 events
Trigger and Interpolator Jitter	≤ 2.5 psrms (typical) <0.1 ps RMS (typical, software assisted)
Internal Trigger Level Range	±4.1 div from center (typical)
External Trigger Level Range	Ext (±0.4 V); Ext/10 (±4 V)
Maximum Trigger Rate	650,000 waveforms/second (in Sequence Mode, up to 8 channels)
Trigger Sensitivity with Edge Trigger ProBus Inputs	2 div @ < 1 GHz 1.5 div @ < 500 MHz 1 div @ < 200 MHz 0.9 div @ < 10 MHz (DC, AC, and LFRej coupling, ≥ 2 mV/div, 50 Ω)
Trigger Sensitivity with Edge Trigger (Aux Input)	4.5 div @ < 1 GHz 1.5 div @ < 500 MHz 1 div @ < 200 MHz 0.9 div @ < 10 MHz (DC, AC, and LFRej coupling)
Max. Trigger Frequency, SMART Trigger	1 GHz
Trigger Types
Edge	Triggers when signal meets slope (positive, negative, or either) and level condition.
Width	Triggers on positive or negative glitches with selectable widths. minimum width 750ps, Maximum Width: 20s
Glitch	Triggers on positive or negative glitches with selectable widths. minimum width 750ps, Maximum Width: 20s
Window	Triggers when signal exits a window defined by adjustable thresholds
Pattern	Logic combination (AND, NAND, OR, NOR) of up to 9 inputs (8 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
Runt	Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
Slew Rate	Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
Interval	Triggers on intervals selectable between 1 ns and 20 s.
Dropout	Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
Measurement Trigger	Select from a large number of measurement parameters. Trigger on a measurement value with qualified limits.
Multi-Stage: Qualified (Timeout or State/Edge Qualified)	Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels).
Triggers with Exclusion Technology	Glitch, Width, Interval, Runt, Slew Rate - Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
Multi-Stage: Qualified First	In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels).
TriggerScan	A Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially.
Low Speed Serial Protocol Trigger (Optional)
Supported Protocols	I2C, I3C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, SENT, MIL-STD-1553, AudioBus (I2S, LJ, RJ, TDM), USB1.x/2.0, SPMI
Measurement Tools
Measurement Functionality	Display up to 12 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state.
Measurement Parameters - Horizontal + Jitter	Cycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min
Measurement Parameters - Vertical	Amplitude, Base, [email protected], Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top.
Measurement Parameters - Pulse	Area, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%)
Measurement Parameters - Statistical (on Histograms)	Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total)
Math Tools
Math Functionality	Display up to 12 math functions traces (F1-F12). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math.
Math Operators - Basic Math	Average (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+).
Math Operators - Digital (incl. with MSO models/options)	Digital AND, Digital DFlipFlop, Digital NAND, Digital NOR, Digital NOT, Digital OR, Digital XOR
Math Operators - Filters	Enhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x.
Math Operators - Frequency Analysis	FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows.
Math Operators - Functions	Absolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity).
Math Operators - Other	Segment, Sparse
Measurement and Math Integration
Measurement and Math Integration	Histograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma)
Pass/Fail Testing
Pass/Fail Testing	Display up to 12 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value <. ≤, =, >, ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook.
Display System
Size	Color 15.6" widescreen capacitive touch screen
Resolution	1920 x 1080 pixels
Number of traces	Display a maximum of 40 traces. Simultaneously display channel, zoom, memory, and math.
Grid Styles	Auto, Single, Dual, Triplex, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Triad, Quattro, Twelve, Sixteen, Twenty. Supports Normal Display Mode (1 grid style, selectable) or Q-Scape Display Mode (4 different tabs, each with individually selectable grid styles). Q-Scape tabbed displays may be viewed in Single, Dual, or Mosaic mode.
Waveform Representation	Sample dots joined, or sample dots only
Persistence Display
Analog and Color-Graded Persistence	Waveforms of ≤500Mpts: Variable saturation levels; stores each trace’s persistence data in memory
Persistence Types	Waveforms of ≤500Mpts: Select analog, color, or three-dimensional
Trace Selection	Waveforms of ≤500Mpts: Activate persistence on all or any combination of traces
Persistence Aging	Waveforms of ≤500Mpts: Select from 500 ms to infinity
Sweep Display Modes	Waveforms of ≤500Mpts: All accumulated, or all accumulated with last trace highlighted
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 12 Zoom and 12 Math/Zoom traces
Internal Waveform Memory
Internal Waveform Memory	12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
Setup Storage
Front Panel and Instrument Status	Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
Automatic Setup
Auto Setup	Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale	Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
Calibration
Calibration Stability	Calibration ensured within +/-5°C operating temperature. Manual calibration may be invoked if outside this temperature range.
Processor/CPU
Type	Intel® Core i5-6500 Quad Core, 3.2 GHz (or better)
Processor Memory	16 GB standard for standard memory with 32 GB optional. 32 GB standard for any memory option.
Operating System	Microsoft Windows® 10
Oscilloscope Operating Software	Teledyne LeCroy MAUI™ with OneTouch
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Connectivity
Ethernet Port	2 x 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Host Ports	4 side USB 3.1 Gen1 ports, 2 front USB 3.1 Gen1 ports
USB Device Port	1 port - USBTMC over USB 3.1 Gen1
GPIB Port (optional)	Supports IEEE - 488.2 (External)
External Monitor Port	1 x DisplayPort, supports up to 4096x2304 @ 24 Hz 1 x HDMI, supports up to 4096x2304 @ 60 Hz
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Compatible
Auxiliary Input
Signal Types	For external trigger input
Coupling	50 Ω: DC; 1 MΩ: AC, DC, GND
Max. Input Voltage	50 Ω 5V RMS, +/- 10V Peak 1 MΩ 400 V max (Peak DC+AC)
Auxiliary Output
Signal Types	Select from output signal, control signals, off
Output Signal	500 Hz-5 MHz square wave or DC level; 3.3 V +/- 10% into 1 MΩ
Control Signals	Trigger enabled, trigger out, pass/fail status, off
Connector Type	BNC, located on rear panel
Probes
Probes	Qty. (4) ÷10 Passive Probes
Probe System	ProBus. Automatically detects and supports a variety of compatible probes
Scale Factors	Automatically or manually selected depending on probe used
Calibration Output	Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 500 Hz to 1 MHz square wave; 50 mV to 1.0V.
Power Requirements
Voltage	100 - 240 VAC ±10% at 47 - 63 Hz 100 - 120 VAC ±10% at 380 - 420 Hz Automatic AC Voltage Selection
Nominal Power Consumption	400 W / 400 VA
Max. Power Consumption	500 W / 500 VA (with all PC peripherals and active probes connected to 8 channels)
Environmental
Temperature (Operating)	+5 °C to +40 °C
Temperature (Non-Operating)	-20 °C to +60 °C
Humidity (Operating)	5% to 90% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +30 °C
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.31 grms 5 Hz to 500 Hz, 20 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Size and Weight
Dimensions (HWD)	13.6”H x 17.5”W x 7.7”D (345 mm x 445 mm x 196 mm)
Weight	24.4 lbs (11.1 kg)
Shipping Weight	37 lbs (16.8 kg)
Certifications
CE Certification UL and cUL Listing	CE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No. 61010-1-12
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.

WaveRunner 8208HD　スペック

Vertical - Analog Channels
Analog Bandwidth (Max)	2 GHz
Analog Bandwidth @ 50 Ω (-3 dB) (ProBus Input)	2 GHz (≥1 mV/div)
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input)	500 MHz
Rise Time (10-90%, 50 Ω)	235 ps
Rise Time (20-80%, 50 Ω)	176 ps
Input Channels	8
Vertical Resolution	12 bits; up to 15 bits with enhanced resolution (ERES)
Effective Number of Bits (ENOB)	8.4 bits
Vertical Noise Floor (1 mV/div)	170 µVrms
Vertical Noise Floor (2 mV/div)	170 µVrms
Vertical Noise Floor (5 mV/div)	175 µVrms
Vertical Noise Floor (10 mV/div)	200 µVrms
Vertical Noise Floor (20 mV/div)	235 µVrms
Vertical Noise Floor (50 mV/div)	330 µVrms
Vertical Noise Floor (100 mV/div)	510 µVrms
Vertical Noise Floor (200 mV/div)	2.35 mVrms
Vertical Noise Floor (500 mV/div)	3.25 mVrms
Vertical Noise Floor (1 V/div)	5.20 mVrms
Sensitivity	50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	±(0.5%) FS, offset at 0 V
Channel-Channel Isolation	DC-200 MHz: 70 dB (>3000:1), 200-500 MHz: 60 dB (>1000:1), 500 MHz - 1 GHz: 50 dB (>300:1), 1 GHz - 2 GHz: 40 dB (>100:1) (For any two input channels, same V/div settings, typical)
Offset Range	50 Ω ±1.6 V @ 1 mV - 4.95 mV/div ±4 V @ 5 mV - 9.9 mV/div ±8 V @ 10 mV - 19.8 mV/div ±10 V @ 20 mV - 1 V/div 1 MΩ ±1.6 V @ 1 mV - 4.95 mV/div ±4 V @ 5 mV - 9.9 mV/div ±8 V @ 10 mV - 19.8 mV/div ±16 V @ 20 mV - 100 mV/div ±80 V @ 102 mV - 198 mV/div ±160 V @ 200 mV - 1 V/div ±400 V @ 1.02 V - 10 V/div
DC Vertical Offset Accuracy	±(0.5% of offset setting + 0.5% FS + 1mV)
Maximum Input Voltage	50 Ω: 5 Vrms, 1 MΩ: 400 V max (DC + Peak AC ≤ 10 kHz)
Input Coupling	1 MΩ: AC, DC, GND; 50 Ω: DC, GND
Input Impedance	50 Ω+/-2% or 1 MΩ||19pF, 10 MΩ || 10 pF
Bandwidth Limiters	20MHz, 200MHz, 350 MHz, 500 MHz, 1 GHz
Rescaling	Length: meters, inches, feet, yards, miles; Mass: grams, slugs; Temperature: celsius, fahrenheit, kelvin; Angle: radian, arcdegr, arcmin, arcsec, cycles, revolutions, turns; Velocity: m/s, in/s, ft/s, yd/s, miles/s; Acceleration: m/s2, in/s2, ft/s2, g0; Volume: liters, cubic meters, cubic inches, cubic feet, cubic yards; Force (Weight): newton, grain, ounce, pound; Pressure: pascal, bar, atmosphere (technical), atmosphere (standard), torr, psi; Electrical: volts, amps, watts, volt-amperes, volt-amperes reactive, farad, coulomb, ohm, siemen, volt/meter, coulomb/m2, farad/meter, siemen/meter, power factor; Magnetic: weber, tesla, henry, amp/meter, henry/meter; Energy: joule, Btu, calorie; Rotating Machine: radian/second, frequency, revolution/second, revolution/minute, N?m, lb-ft, lb-in, oz-in, watt, horsepower; Other: %.
Horizontal - Analog Channels
Timebases	Internal timebase common to 8 input channels
Acquisition Modes	Real-time, Roll, Sequence
Time/Division Range	100 ps/div - 5 ks/div with standard memory (up to 10 ks/div with 500MPT memory, 25 ks/div with 1000MPT memory, 50 ks/div with 2000MPT memory, 100 ks/div with 5000MPT memory); Roll Mode available at ≥ 100 ms/div and ≤ 5 MS/s
Clock Accuracy	+/-1 ppm + 1 ppm/year from calibration
Sample Clock Jitter	up to 10µs Acquired Time Range: 80 fsrms (Internal Timebase Reference) up to 10ms Acquired Time Range: 150 fsrms (Internal Timebase Reference)
Delta Time Measurement Accuracy	\sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds)
Jitter Measurement Floor	\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)}
Channel-Channel Deskew Range	±9 x time/div. setting, 100 ms max., each channel
External Timebase Reference (Input)	10MHz +/-25ppm at 0 to 10dBm into 50 Ohms
External Timebase Reference (Output)	10MHz, 5.0 dBm +/-2.5 dBm, sinewave synchronized to reference being used (internal or external reference)
Acquisition - Analog Channels
Sample Rate (Single-shot)	10 GS/s on 8 Ch with Enhanced Sample Rate
Memory Length (4 Ch / 2 Ch / 1Ch) (Number of Segments)	50M/100M/200M (65,536)
Memory Length Options (4 Ch / 2 Ch / 1Ch) (Number of Segments)	WR8KHD-500MPT Option: 125M / 250M / 500M (65,535) WR8KHD-1000MPT Option: 250M / 500M / 1000M (65,535) WR8KHD-2000MPT Option: 500M / 1000M / 2000M (65,535) WR8KHD-5000MPT Option: 1250M / 2500M / 5000M (65,535) Maximum analysis memory: 500 Mpts per channel
Intersegment Time	1.5 µs
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps (Waveforms of ≤500Mpts)
Enhanced Resolution (ERES)	From 12.5 to 15 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps (Waveforms of ≤500Mpts)
Interpolation	Linear or Sin x/x (2 pt and 5 pt) (Waveforms of ≤500Mpts)
Vertical, Horizontal, Acquisition - Digital Channels
Maximum Input Frequency	500 MHz
Minimum Detectable Pulse Width	1 ns
Input Channels	16 Digital channels (with WR8KHD-MSO option)
Input Impedance (Flying Leads)	100 kΩ || 5 pF
Input Dynamic Range	± 20V
Maximum Input Voltage	±30V Peak
Maximum Input Voltage Swing	400mV
Threshold Groupings	Pod 2: D15 - D8, Pod 1: D7 - D0
Threshold Selections	TTL, ECL, CMOS (2.5 V, 3.3 V, 5 V), PECL, LVDS or User Defined
Threshold Accuracy	±(3% of threshold setting + 100mV)
User Defined Threshold Range	±10 V in 20 mV steps
User Defined Hysteresis Range	100 mV to 1.4 V in 100 mV steps
Sample Rate	2.5GS/s
Record Length	Standard: 50 Mpts Any memory option: 500 Mpts
Channel-to-Channel Skew	350 ps
Triggering System
Modes	Acquisition of ≤500Mpts: Normal, Auto, Single, and Stop Acquisition of >500Mpts: Single
Sources	Any input channel, Ext, Ext/10, or Line; slope and level unique to each source (except line trigger)
Coupling	DC, AC, HFRej, LFRej
Pre-trigger Delay	0-100% of memory size
Post-trigger Delay	No limitation
Hold-off	From 2 ns up to 20 s or from 1 to 99,999,999 events
Trigger and Interpolator Jitter	≤ 2.5 psrms (typical) <0.1 ps RMS (typical, software assisted)
Internal Trigger Level Range	±4.1 div from center (typical)
External Trigger Level Range	Ext (±0.4 V); Ext/10 (±4 V)
Maximum Trigger Rate	650,000 waveforms/second (in Sequence Mode, up to 8 channels)
Trigger Sensitivity with Edge Trigger ProBus Inputs	2.5 div @ < 1 GHz 2 div @ < 1 GHz 1.5 div @ < 500 MHz 1 div @ < 200 MHz 0.9 div @ < 10 MHz (DC, AC, and LFRej coupling, ≥ 2 mV/div, 50 Ω)
Trigger Sensitivity with Edge Trigger (Aux Input)	4.5 div @ < 1 GHz 1.5 div @ < 500 MHz 1 div @ < 200 MHz 0.9 div @ < 10 MHz (DC, AC, and LFRej coupling)
Max. Trigger Frequency, SMART Trigger	2 GHz
Trigger Types
Edge	Triggers when signal meets slope (positive, negative, or either) and level condition.
Width	Triggers on positive or negative glitches with selectable widths. minimum width 750ps, Maximum Width: 20s
Glitch	Triggers on positive or negative glitches with selectable widths. minimum width 750ps, Maximum Width: 20s
Window	Triggers when signal exits a window defined by adjustable thresholds
Pattern	Logic combination (AND, NAND, OR, NOR) of up to 9 inputs (8 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
Runt	Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
Slew Rate	Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
Interval	Triggers on intervals selectable between 1 ns and 20 s.
Dropout	Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
Measurement Trigger	Select from a large number of measurement parameters. Trigger on a measurement value with qualified limits.
Multi-Stage: Qualified (Timeout or State/Edge Qualified)	Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels).
Triggers with Exclusion Technology	Glitch, Width, Interval, Runt, Slew Rate - Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
Multi-Stage: Qualified First	In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels).
TriggerScan	A Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially.
Low Speed Serial Protocol Trigger (Optional)
Supported Protocols	I2C, I3C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, SENT, MIL-STD-1553, AudioBus (I2S, LJ, RJ, TDM), USB1.x/2.0, SPMI
Measurement Tools
Measurement Functionality	Display up to 12 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state.
Measurement Parameters - Horizontal + Jitter	Cycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min
Measurement Parameters - Vertical	Amplitude, Base, [email protected], Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top.
Measurement Parameters - Pulse	Area, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%)
Measurement Parameters - Statistical (on Histograms)	Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total)
Math Tools
Math Functionality	Display up to 12 math functions traces (F1-F12). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math.
Math Operators - Basic Math	Average (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+).
Math Operators - Digital (incl. with MSO models/options)	Digital AND, Digital DFlipFlop, Digital NAND, Digital NOR, Digital NOT, Digital OR, Digital XOR
Math Operators - Filters	Enhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x.
Math Operators - Frequency Analysis	FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows.
Math Operators - Functions	Absolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity).
Math Operators - Other	Segment, Sparse
Measurement and Math Integration
Measurement and Math Integration	Histograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma)
Pass/Fail Testing
Pass/Fail Testing	Display up to 12 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value <. ≤, =, >, ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook.
Display System
Size	Color 15.6" widescreen capacitive touch screen
Resolution	1920 x 1080 pixels
Number of traces	Display a maximum of 40 traces. Simultaneously display channel, zoom, memory, and math.
Grid Styles	Auto, Single, Dual, Triplex, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Triad, Quattro, Twelve, Sixteen, Twenty. Supports Normal Display Mode (1 grid style, selectable) or Q-Scape Display Mode (4 different tabs, each with individually selectable grid styles). Q-Scape tabbed displays may be viewed in Single, Dual, or Mosaic mode.
Waveform Representation	Sample dots joined, or sample dots only
Persistence Display
Analog and Color-Graded Persistence	Waveforms of ≤500Mpts: Variable saturation levels; stores each trace’s persistence data in memory
Persistence Types	Waveforms of ≤500Mpts: Select analog, color, or three-dimensional
Trace Selection	Waveforms of ≤500Mpts: Activate persistence on all or any combination of traces
Persistence Aging	Waveforms of ≤500Mpts: Select from 500 ms to infinity
Sweep Display Modes	Waveforms of ≤500Mpts: All accumulated, or all accumulated with last trace highlighted
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 12 Zoom and 12 Math/Zoom traces
Internal Waveform Memory
Internal Waveform Memory	12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
Setup Storage
Front Panel and Instrument Status	Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
Automatic Setup
Auto Setup	Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale	Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
Calibration
Calibration Stability	Calibration ensured within +/-5°C operating temperature. Manual calibration may be invoked if outside this temperature range.
Processor/CPU
Type	Intel® Core i5-6500 Quad Core, 3.2 GHz (or better)
Processor Memory	16 GB standard for standard memory with 32 GB optional. 32 GB standard for any memory option.
Operating System	Microsoft Windows® 10
Oscilloscope Operating Software	Teledyne LeCroy MAUI™ with OneTouch
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Connectivity
Ethernet Port	2 x 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Host Ports	4 side USB 3.1 Gen1 ports, 2 front USB 3.1 Gen1 ports
USB Device Port	1 port - USBTMC over USB 3.1 Gen1
GPIB Port (optional)	Supports IEEE - 488.2 (External)
External Monitor Port	1 x DisplayPort, supports up to 4096x2304 @ 24 Hz 1 x HDMI, supports up to 4096x2304 @ 60 Hz
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Compatible
Auxiliary Input
Signal Types	For external trigger input
Coupling	50 Ω: DC; 1 MΩ: AC, DC, GND
Max. Input Voltage	50 Ω 5V RMS, +/- 10V Peak 1 MΩ 400 V max (Peak DC+AC)
Auxiliary Output
Signal Types	Select from output signal, control signals, off
Output Signal	500 Hz-5 MHz square wave or DC level; 3.3 V +/- 10% into 1 MΩ
Control Signals	Trigger enabled, trigger out, pass/fail status, off
Connector Type	BNC, located on rear panel
Probes
Probes	Qty. (4) ÷10 Passive Probes
Probe System	ProBus. Automatically detects and supports a variety of compatible probes
Scale Factors	Automatically or manually selected depending on probe used
Calibration Output	Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 500 Hz to 1 MHz square wave; 50 mV to 1.0V.
Power Requirements
Voltage	100 - 240 VAC ±10% at 47 - 63 Hz 100 - 120 VAC ±10% at 380 - 420 Hz Automatic AC Voltage Selection
Nominal Power Consumption	400 W / 400 VA
Max. Power Consumption	500 W / 500 VA (with all PC peripherals and active probes connected to 8 channels)
Environmental
Temperature (Operating)	+5 °C to +40 °C
Temperature (Non-Operating)	-20 °C to +60 °C
Humidity (Operating)	5% to 90% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +30 °C
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.31 grms 5 Hz to 500 Hz, 20 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Size and Weight
Dimensions (HWD)	13.6”H x 17.5”W x 7.7”D (345 mm x 445 mm x 196 mm)
Weight	24.4 lbs (11.1 kg)
Shipping Weight	37 lbs (16.8 kg)
Certifications
CE Certification UL and cUL Listing	CE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No. 61010-1-12
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.

デモビデオ

業界初！8GHz広帯域、12ビット高分解能を同時に実現！

業界初！8GHz広帯域、12ビット高分解能を同時に実現！ より多くのチャンネル数、より柔軟な計測　 HD4096テクノロジで常時12ビットを実現したオシロスコープ　 より多くの波形メモリが必要ではありませんか？─最長5Gポイントの波形メモリ

ページトップへ  

主な機能

• アナログ8チャンネル
• 帯域幅：350MHz、500MHz、1GHz、2GHz（帯域アップグレード可能）
• 12ビットADC分解能
  分解能向上演算（ERES）使用時に最大15ビット
  − DCゲイン精度：±0.5%フルスケール
• 低ノイズ：85μ[email protected]/div（WaveRunner 8038HD）
• 最高サンプリング速度：10GS/s
• ロングメモリ：最長5Gポイント/ch
• 15.6インチ、フルHD静電容量式タッチ・スクリーン
• ロジック16ch（WR8KHD-MSOオプション）
• Windows 10

対応アプリケーション

• 高速組み込みコンピュータ・システム
• 三相モータ／インバータ
• パワー・インテグリティ試験
• 車載システム

広帯域2GHzと12ビットの高分解能を同時に実現

他社の機器では、帯域と分解能の間にトレードオフの関係があり、いずれかを犠牲にしなければなりませんが、WaveRunner 8000HDシリーズでは、常時12ビットの高分解能を2GHzの広帯域と同時に実現します。

0.5%のDCゲイン確度

85μ[email protected]/div（WaveRunner 8038HD）のローノイズ設計と12ビットの高分解能で2GHzの広帯域でもDCゲイン確度0.5%を実現し、高精度の測定を保証します。

5Gポイントの超ロングメモリ

WaveRunner 8000HDシリーズは最大で5Gポイントの業界最高のロングメモリを実現しました。10GS/sの最高サンプリング速度で、500msの長時間の波形捕捉が可能です。

三相モータ解析用MDAモデル

WaveRunner 8000HDシリーズの高い性能を活用し、三相モータ／インバータ解析のソフトを標準搭載したMDA 8000HDモータ・ドライブ・アナライザを用意しました。

16チャンネル・システム

チャンネル同期オプションOscilloSYNC (WR8KHD-16CH-SYNCH) を使ってオシロスコープ2台を同期運転させることで、簡単に16チャンネルのシステムを構築できます。

組み込み機器、車載エレクトロニクスや三相パワーエレクトロニクス開発に最適

WaveRunner 8000HDシリーズは、多チャンネル、高分解能による三相モーター／インバータの解析のみならず、2GHzの広帯域によって、複雑な組み込み回路や車載エレクトロニクスの解析やデバックに役立つ様々なオプションにも対応し、この一台で開発の全てをサポートします。

● 信号の細部まで表示

ローノイズ・フロントエンドと垂直分解能の向上で、今まで不可能だった波形の詳細が観測できます。特に従来の8ビット・オシロスコープでは分解能の不足により不可能だったON領域のスイッチング・デバイスの動作解析（動作状態でのON抵抗測定）が可能になります。

● タブレット感覚の操作性

OneTouch MAUI（ワンタッチマウイ）を搭載したWaveRunner 8000HDシリーズは、タブレット等で一般的なジェスチャを採用することで直感的な操作が可能になり設定時間が劇的に短くなります。全ての一般的な操作がポップアップ・メニューや設定メニューを開かなくともワンタッチ操作で行えます。

● 2GHz帯域で複雑な組み込みシステムのデバッグに最適

シリアル解析ツールやMSOオプションに対応し、パワーエレクトロニクス、電力、クロック、デジタル・ロジック、シリアル・データおよびアナログ・センサ信号を複雑に組み合わせた自動車電子制御ユニット（ECU）、家電（洗濯機、冷蔵庫等）、産業システム（ロボット工学等）等に使用される組み込みシステムのデバッグに最適です。2GHzの帯域があり、1000Base-T1など車載イーサネット信号評価にも対応できます。

● 開発を支える様々なプローブ群に対応

テレダイン・レクロイのProBusプローブ・インタフェースに対応。高圧、高圧差動、電流プローブ等様々なプローブで開発をサポートします。また最大8本の電流プローブを同時に使用することが可能です。

● MDAモータ・ドライブ・アナライザ

MDA 8000HDシリーズは、2GHz、12ビット、8チャンネルのWaveRunner 8000HDシリーズの仕様を活かし高い評価をうけるモータ／インバータ解析の機能をさらに進化させました。またOscilloSYNCを使った16チャンネルシステムでは、複雑さを増すモータ駆動部と制御システムとの関連付けた解析などより複雑な解析が可能になります。

クリックで詳細表示されます

クリックで詳細表示されます

他社比較

唯一の8チャンネル、 12ビット、2GHzオシロスコープ （Waverunner 8000HD vs テクトロニクス 5シリーズ）

三相または1kW以上の電力変換 （Waverunner 8000HD vs テクトロニクス 5シリーズ）

パワーインテグリティおよびパワーシーケンス解析 （Waverunner 8000HD vs テクトロニクス 5シリーズ）

車載エレクトロニクス （Waverunner 8000HD vs テクトロニクス 5シリーズ）

高機能 組み込みコンピュータ・システム （Waverunner 8000HD vs テクトロニクス 5シリーズ）

ページトップへ