MAXIMUM RATINGSymbolParameterMinTypMaxUnitsComments
VccPositive Supply Voltage5.006.00V
VEE Negative Supply Voltage-5.20-6.00V
Input Voltage±4.00V
Differential Input Voltage±4.00V
Output Current30.00mAPer output pin
Power Dissipation800.00mW
T Operating Temperature-20.0025.0070.00¡ C
ELECTRICAL CHARACTERISTICS
IOSInput offset current-0.50±0.050.50µASee Fig. 1
ÆIOS/ÆTAvg. Temp. Const. of IOS-1.50±0.501.50nA/¡C
IBInput bias current3.505.007.00µASee Fig. 1
ÆIB/ÆTAvg. Temp. Const. of IB-40.00-20.000.00nA/¡CSee Fig. 11
RinInput resistance20.0030.00ÑKW
CinInput capacitance1.201.602.10pF
VcmInput voltage range-2.00Ñ1.70VSee Figs. 2, 14
VT+Threshold for OUT-1.002.405.00mVSee Fig. 4, Note 4
VT-Threshold for OUT-6.00-2.400.00mVSee Fig. 4, Note 4
ÆVT±/ÆTAvg. Temp. Const. of VT±-10.00±5.0010.00µV/¡CSee Fig. 4, Note 4
VHHysteresis voltage4.604.805.00mVSee Fig. 4, Note 4
VOLOutput low level-1.85-1.71-1.63VSee Fig. 3, RT = 510 ohm, VT = -5.2 V
VOHOutput high level-0.96-0.84-0.80VSee Fig. 3, RT = 510 ohm, VT = -5.2 V
ÆVOH/ÆTAvg. Temp. Const. of VOHÑ1.50ÑmV/¡C
ÆVOL/ÆTAvg. Temp. Const. of VOLÑ0.60ÑmV/¡C
I+Positive supply currentÑ40.0050.00mA4 channels without output pulldown resistors, See Fig. 1
I-Negative supply currentÑ37.0047.00mA4 channels without output pulldown resistors, See Fig. 1
PDPower dissipationÑ392.00494.00mW4 channels without output pulldown resistors, See Fig. 1
SWITCHING CHARACTERISTICS
tpdPropagation delay3.003.504.00nsec50 mV overdrive Notes 2, 4. See Fig. 3, RT = 510 ohm, VT = -5.2 V
Ætpd/ÆTAvg. Temp. Const. of prop. delayÑ2.00Ñpsec/¡C0 to 70¡C
tr, tfTransition time0.801.201.40nsecRT = 50 ohm, VT = -2 V, Fig. 3
tr, tfTransition time0.500.851.20nsecRT = 510 ohm, VT = -5.2 V, Fig. 3
DPRDouble pulse resolutionÑ2.00ÑnsecNotes 3, 4
fmaxMax. toggle frequencyÑ400.00ÑMHz
TminMin. input widthÑ1.00Ñnsec
INTERCHANNEL MATCHING*
ÆVHHysteresisѱ0.25ÑmV
ÆVT±Threshold voltageѱ1.25ÑmV
ÆIOSInput offset currentѱ50.00ÑnA
ÆtpdPropagation delayѱ125.00Ñpsec
Cross talk - any channelÑÑÑdBUnobservable, Note 1
*Interchannel matching refers to the variation between the channels on any single chip.
Notes:
1. Cross talk is measured at a threshold of 2 mV.
2. Propagation delays are defined as the delay between a positive going input and an output transition of either polarity. The input overdrive is 50 mV with the threshold set at 0 mV.
3. Double pulse resolution is defined as the minimum pulse pair spacing at which the MVL407 responds to the second pulse of the pair. The output levels of the second pulse must cross VOH and VOL. See Figure 5.
4. See Application Hints.
5. Characteristics measured at VCC = +5.0 V, VEE = -5.2 V and T = 25¡C.