モジュール型・
オシロスコープ・システム
LabMaster 10Zi-Aシリーズ

• 最高65 GHzの帯域幅
• 最高80 Channels @ 36 GHzのチャンネル数
• 最高160 GS/sのサンプリング速度
• 1024 Mpts/Ch
• 50fsrms サンプルクロック

LabMaster 10Zi-Aシリーズモジュール型・オシロスコープ・システムはオシロスコープの性能と可能性を完全に刷新します。

• 広帯域幅でのマルチチャンネル操作
  − [email protected] 65, 60 or 50 GHz帯域
  − [email protected] 36, 30, or 25 GHz帯域
• 帯域幅とチャンネル数の柔軟なアップグレード
• channnelSync^TMによる全ての捕捉モジュールの正確な同期 (130fsrms Jitter Between All Channels)
• サーバークラスCPU(33.6GHz実効クロックレート、最大192GB RAM)
• 4.9 ps (20-80%) 立ち上がり時間
• 80bit NRZ / 8B10Bシリアル・パターン・トリガ（〜14.1Gbps）
  　

LabMasterモジュール型リアルタイム・オシロスコープのアーキテクチャは、オシロスコープのアクイジション（信号捕捉）機能をディスプレイ、制御、および処理機能と分離しています。 LabMasterコントロール・モジュールには、ディスプレイ、制御、ChannelSyncアーキテクチャ、強力なサーバークラスのCPUが含まれています。

LabMaster 10Ziアクイジション・モジュールは、シリコンベースの36 GHzのチップを使い、2つの入力チャネルで最高65 GHzまで帯域の性能を提供します。1つのLabMaster 10Ziコントロール・モジュールと1つのLabMaster 10Ziアクイジション・モジュールの組み合わせにより、4チャネル36 GHz帯域のオシロスコープとして、または2チャネル65 GHz帯域／4チャネル36 GHz帯域のオシロスコープとして使用することができます。

また、ChannelSyncアーキテクチャを使用して最大20台のアクイジション・モジュールを完全に同期させることができます。これにより、36 GHz帯域80チャネル、或いは65 GHz帯域40チャネルまでのシステムが実現可能です。LabMaster用に新しく発表された拡張モジュールは、以前にのものと比べチャネル密度（帯域×チャネル数）を4倍に高めることができます。

LabMasterのChannelSyncアーキテクチャの利点は他にもあります。すべてのアクイジション・モジュールが共通して利用する単一のサンプリング・クロックとトリガ回路により、最大80チャネル入力時にも、最高の信号捕捉精度を提供します。アクイジション･モジュールは「プラグアンドプレイ」に対応した設計のため、特別なプログラミング、外部サンプリング、クロック同期、オシロスコープ間の複雑な接続などは必要ありません。

コントロール・モジュールにはディスプレイとサーバークラス（12コア型）中央処理装置（CPU）があります。すべてのアクイジション・モジュールから取得した波形は、従来のオシロスコープのように、ひとつのディスプレイに表示されます。複数のアクイジション・モジュールを持つシステム全体の接続とセットアップは、精密なデスキュー校正を含めても5〜10分程度で完了します。

ページトップへ

モデルごとスペック詳細（モデル名をクリックで詳細表示されます）

LabMaster 10 Zi-A 20 GHz Systems　スペック

Vertical System
Analog Bandwidth (Max)	20 GHz
Analog Bandwidth @ 50 Ω (-3 dB) (2.4/2.92mm Inputs)	20 GHz (≧5 mV/div)
Rise Time (10-90%, 50 Ω)	19.3 ps (test limit, flatness mode)
Rise Time (20-80%, 50 Ω)	14.5 ps (flatness mode)
Input Channels	Up to 80, depending on configuration selected. (Any combination of up to 80 2.92mm input channels)
Bandwidth Limiters	1, 3, 4, 6, 8, 13, 16 GHz
Input Impedance	2.92mm Inputs: 50 Ω+/-2%
Input Coupling	2.92 mm Inputs: 50 Ω: DC, GND
Maximum Input Voltage	2.92 mm Inputs: ±2 [email protected]＜76mV/div, [email protected]≧76mV/div
Channel-Channel Isolation	DC to 36 GHz: 60 dB (>1000:1) (For any two 2.92mm input channels, same or different v/div settings, typical)
Vertical Resolution	8 bits; up to 11 bits with enhanced resolution (ERES)
Sensitivity	50 Ω (2.92mm): 5 mV-500mV/div, fully variable (5-9.9 mV/div via zoom)
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	±1% F.S. (typical), offset at 0V; ±1.5% F.S. (test limit), offset at 0V
Offset Range	50 Ω: ±500 mV @ 5-75 mV/div ±4 V @ 76 mV/div -500mV/div
Offset Accuracy	50 Ω (2.92mm): 5 mV-500mV/div, fully variable (5-9.9 mV/div via zoom)
DC Vertical Offset Accuracy	±(1.5% of offset setting + 1.5% F.S. + 1 mV) (test limit)
Horizontal System
Timebases	Internal timebase with 10 GHz clock frequency common to all input channels. Single, distributed 10 GHz clock for all channels ensures precise synchronization with timing accuracy between all channels identical to that provided within a single, conventional oscilloscope package.
Time/Division Range	10 ps/div-256 s/div (maximum capture time is based on minimum sample rate of 200kS/s and installed memory).
Clock Accuracy	＜0.1 ppm + (aging of 0.05 ppm/yr from last calibration)
Sample Clock Jitter	up to 3.2ms Acquired Time Range: 50fsrms (Internal Timebase Reference) 50fsrms (External Timebase Reference) up to 6.4ms Acquired Time Range: 130fsrms (Internal Timebase Reference) 130fsrms (External Timebase Reference)
Delta Time Measurement Accuracy	√2*√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) (RMS)+(clock accuracy*reading)(seconds)
Jitter Measurement Floor	√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) secondsrms (TIE)
Jitter Between Channels	＜250fsrms (TIE, typical, measured at maximum bandwidth)
Trigger and Interpolator Jitter	＜0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware),
Channel-Channel Deskew Range	±9 x time/div. setting or 25 ns max. (whichever is larger), each channel
External Timebase Reference (Input)	10 MHz or 100MHz; 50 Ω impedance, applied at the rear input of MCM-Zi-A Master Control Module
External Timebase Reference (Output)	10 MHz or 100 MHz ; 50 Ω impedance, output at the rear of MCM-Zi-A Master Control Module
Acquisition System
Single-Shot Sample Rate/Ch	80 GS/s on each channel.
Maximum Trigger Rate	1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
Intersegment Time	1 μs
Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments)	32 M / 32 M / 32M (1000)
Memory Options (4 Ch / 2 Ch / 1Ch) (Number of Segments)	S-32 Option: 32M / 32M / 32M (7,500) M-64 Option: 64M / 64M / 64M (15,000) L-128 Option: 128M / 128M / 128M (15,000) VL-256 Option: 256M / 256M / 256M (15,000) XL-512 Option: 512M / 512M / 512M (15,000)
Acquisition Processing
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
Enhanced Resolution (ERES)	From 8.5 to 11 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps
Interpolation	Linear or Sin x/x
Triggering System
Modes	Normal, Auto, Single, and Stop
Sources	Any Ch 1-4 (Edge, Window, SMART, Cascade triggers), AUX, internal Fast Edge; or any input channel (Edge trigger only) on additional 10-xxZi-A Acquisition Modules (Channels 5 and higher). Slope and level unique to each source except line trigger.
Coupling Mode	DC, AC, HFRej, LFRej
Pre-trigger Delay	0-100% of memory size (adjustable in 1% increments of 100 ns)
Post-trigger Delay	0-10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
Hold-off by Time or Events	From 2 ns up to 20 s or from 1 to 99,999,999 events
Internal Trigger Range	±4.1 div from center
Trigger Sensitivity with Edge Trigger (1.85/2.4/2.92mm Inputs)	For Ch 1-80 of a LabMaster 10 Zi-A system: 3 div @ ＜ 12 GHz 1.5 div @ ＜ 3 GHz 1.0 div @ ＜ 200 MHz (for DC coupling, ≧ 10 mV/div, 50 Ω)
External Trigger Sensitivity, (Edge Trigger)	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2 div @ ＜ 1 GHz, 1.5 div @ ＜ 500 MHz, 1.0 div @ ＜ 200 MHz, (for DC coupling)
Max. Trigger Frequency, SMART Trigger	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2.0 GHz @ ≧ 10 mV/div (minimum triggerable width 200 ps)
External Trigger Input Range	For any LabMaster 10xx-Zi-A Acquisition Module: Aux (±0.4 V) (Only Ch1-4 Acquisition Module has "active" AUX Input)
Basic Triggers
TV-Composite Video	Not available
High Speed Serial Protocol Triggering
Data Rates	Option LM10Zi-6GBIT-80B-8B10B-TD: 600 Mb/s to 6.5 Gb/s, Channel 4 input only Option LM10Zi-14GBIT-80B-8B10B-TD: 600 Mb/s to 14.1 Gb/s, Channel 4 input only
Pattern Length	80 bits NRZ, eight 8b/10b symbols
Clock and Data Outputs	No Clock and Data Recovery outputs provided
Measurement Trigger
Measurement Trigger Capability	0
Color Waveform Display
Type	On LabMaster MCM-Zi Master Control Module: Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
Resolution	WXGA; 1280 x 768 pixels.
Number of traces	Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces.
Grid Styles	Auto, Single, Dual, Triple, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Twelve, Sixteen. Up to twenty grids available with some software options.
Waveform Representation	Sample dots joined, or sample dots only
Internal Waveform Memory
Internal Waveform Memory	12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
Integrated Second Display
Type	Supports touch screen integration of user-supplied second display with split-grid capability. (Note: touch screen driver for second display may not be a Fujitsu driver)
Resolution	Determined by display chosen by user
LeCroy WaveStream Fast Viewing Mode
Intensity	256 Intensity Levels, 1-100% adjustable via front panel control
Types	Select analog or color-graded
Number of Channels	up to 80 simultaneously
Max Sampling Rate	80 GS/s
Persistence Aging	Select from 500 ms to Infinity
Waveforms/second (continuous)	up to 2500 Waveforms/second
Operation	Front panel toggle between WaveStream ON (Analog), ON (Color) and OFF
Analog Persistence Display
Analog and Color-Graded Persistence	Variable saturation levels; stores each trace's persistence data in memory
Persistence Types	Select analog, color, or three-dimensional
Trace Selection	Activate persistence on all or any combination of traces
Persistence Aging	Select from 500 ms to infinity
Sweep Display Modes	All accumulated, or all accumulated with last trace highlighted
High Speed Digitizer Output (Option)
Type	Option LSIB-2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
Transfer Rate	up to 325 MB/s (typical) - Maximum of 4 channels (consult Teledyne LeCroy for >4 channels)
Output Protocol	PCI Express, Gen 1 (4 lanes utilized for data transfer)
Control Protocol	TCP/IP
Command Set	Via Windows Automation, or via LeCroy Remote Command Set
Processor/CPU
Processor Memory	32 GB standard. Up to 192 GB optionally available.
Operating System	Microsoft WindowsR 7 Professional Edition (64-bit)
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 12 Zoom and 12 Math/Zoom traces
Setup Storage
Front Panel and Instrument Status	Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
Interface
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Class C (v1.2) Compliant
GPIB Port	Supports IEEE - 488.2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
LSIB Port (optional)	Supports PCIe Gen1 x4 protocol with LeCroy supplied API. Installs in LabMaster LabMaster MCM-Zi-A Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi-A Acquisition Module.
Ethernet Port	Supports 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Ports	LabMaster MCM-Zi -A Master Control Module: minimum 2 total USB 2.0 ports on rear of unit to support Windows compatible devices LabMaster MCM-Zi -A Master Control Module: minimum 3 total USB 2.0 ports on front of unit to support Windows compatible devices
External Monitor Port	Dual Link DVI compatible to support internal display on MCM-Zi Master Control Module (1280 x 768 pixel resolution) and customer-supplied monitor with up to WQXGA (2560 x 1600 pixel) resolution using extended desktop mode.
Auxiliary Input
Signal Types	For External Trigger Input. Located on every LabMaster 10-xxZi-A Acquisition Module (front-mounted BNC, 50 Ω). 10-xxZi-A Acquisition Module that is used for Channels 1-4 contains "active" AUX Input.
Coupling	50 Ω: DC
Max. Input Voltage	5 Vrms
Auxiliary Output
Signal Types	Select from calibrator, control signals or Off
Output Signal	500 Hz-5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0-1 V into 1 MΩ)
Control Signals	Trigger enabled, trigger out, pass/fail status, off
Connector Type	BNC, located on front of every LabMaster 10-xxZi Acquisition Module. 10-xxZi Acquisition Module that is used for Channels 1-4 contains "active" AUX Output.
Automatic Setup
Auto Setup	Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale	Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
General
Auto Calibration	Ensures specified DC and timing accuracy is maintained for 1 year minimum.
Probes
Probes	No passive probes supplied
Probe System	2.92mm interface automatically detects and supports a variety of compatible probes. Use L2.92A-PLINK or L2.92A-PBUS 2.92mm Probe Adapters to connect 50Ω ProLink or 50Ω ProBus compatible probes to 2.92mm interface.
Scale Factors	Automatically or manually selected depending on probe used
Calibration Output	MCM-Zi-A Master Control Module: Fast Edge output, 5MHz square wave, 350mVp-p (typical), 50ps rise time, output to SMA connector, AC Coupled
Power Requirements
Voltage	LabMaster 10-xxZi Acquisition Module: 100-240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection, Installation Category II LabMaster MCM-Zi Master Control Module: 100-240 VAC ±10% at 45-66 Hz; Automatic AC Voltage Selection, Installation Category II
Max. Power Consumption	LabMaster 10-xxZi-A Acquisition Module - 1225 W / 1225 VA. LabMaster MCM-Zi-A Master Control Module - 450 W / 450 VA. Each Module and the CPU has a separate power cord.
Environmental and Safety
Temperature (Operating)	+5 ℃ to +40 ℃
Temperature (Non-Operating)	-20 ℃ to +60 ℃
Humidity (Operating)	5% to 80% relative humidity (non-condensing) up to +31 ℃. Upper limit derates to 50% relative humidity (non-condensing) at +40 ℃.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +25 ℃
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Physical Dimensions
Dimensions (HWD)	LabMaster MCM-Zi-A Master Control Module - 10.9"H x 18.2"W x 15.6"D (277 x 462 x 396 mm), LabMaster 10-xxZi-A Acquisition Module - 8.0"H x 18.2"W x 26"D (202 x 462 x 660 mm)
Weight	LabMaster 10-xxZi-A Acquisition Module -53 lbs. (24.1 kg) LabMaster MCM-Zi-A Master Control Module - 47 lbs. (21.4 kg)
Shipping Weight	LabMaster 10-xxZi-A Acquisition Module -71 lbs. (32.3 kg) LabMaster MCM-Zi-A Master Control Module - 56 lbs. (25.5 kg)
Certifications
Certifications	CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, EN61010-2-030, UL 61010-1 3rd edition, and CSA C22.2 No. 61010-1-12
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.

LabMaster 10 Zi-A 25 GHz Systems　スペック

Vertical System
Analog Bandwidth (Max)	25 GHz
Analog Bandwidth @ 50 Ω (-3 dB) (2.4/2.92mm Inputs)	25 GHz (≧5 mV/div)
Rise Time (10-90%, 50 Ω)	15.4 ps (test limit, flatness mode)
Rise Time (20-80%, 50 Ω)	11.6 ps (flatness mode)
Input Channels	Up to 80, depending on configuration selected. (Any combination of up to 80 2.92mm input channels)
Bandwidth Limiters	1, 3, 4, 6, 8, 13, 16, 20 GHz
Input Impedance	2.92mm Inputs: 50 Ω+/-2%
Input Coupling	2.92 mm Inputs: 50 Ω: DC, GND
Maximum Input Voltage	2.92 mm Inputs: ±2 [email protected]＜76mV/div, [email protected]≧76mV/div
Channel-Channel Isolation	DC to 36 GHz: 60 dB (>1000:1) (For any two 2.92mm input channels, same or different v/div settings, typical)
Vertical Resolution	8 bits; up to 11 bits with enhanced resolution (ERES)
Sensitivity	50 Ω (2.92mm): 5 mV-500mV/div, fully variable (5-9.9 mV/div via zoom)
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	±1% F.S. (typical), offset at 0V; ±1.5% F.S. (test limit), offset at 0V
Offset Range	50 Ω: ±500 mV @ 5-75 mV/div ±4 V @ 76 mV/div -500mV/div
Offset Accuracy	50 Ω (2.92mm): 5 mV-500mV/div, fully variable (5-9.9 mV/div via zoom)
DC Vertical Offset Accuracy	±(1.5% of offset setting + 1.5% F.S. + 1 mV) (test limit)
Horizontal System
Timebases	Internal timebase with 10 GHz clock frequency common to all input channels. Single, distributed 10 GHz clock for all channels ensures precise synchronization with timing accuracy between all channels identical to that provided within a single, conventional oscilloscope package.
Time/Division Range	10 ps/div-256 s/div (maximum capture time is based on minimum sample rate of 200kS/s and installed memory).
Clock Accuracy	＜0.1 ppm + (aging of 0.05 ppm/yr from last calibration)
Sample Clock Jitter	up to 3.2ms Acquired Time Range: 50fsrms (Internal Timebase Reference) 50fsrms (External Timebase Reference) up to 6.4ms Acquired Time Range: 130fsrms (Internal Timebase Reference) 130fsrms (External Timebase Reference)
Delta Time Measurement Accuracy	√2*√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) (RMS)+(clock accuracy*reading)(seconds)
Jitter Measurement Floor	√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) secondsrms (TIE)
Jitter Between Channels	＜250fsrms (TIE, typical, measured at maximum bandwidth)
Trigger and Interpolator Jitter	＜0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware),
Channel-Channel Deskew Range	±9 x time/div. setting or 25 ns max. (whichever is larger), each channel
External Timebase Reference (Input)	10 MHz or 100MHz; 50 Ω impedance, applied at the rear input of MCM-Zi-A Master Control Module
External Timebase Reference (Output)	10 MHz or 100 MHz ; 50 Ω impedance, output at the rear of MCM-Zi-A Master Control Module
Acquisition System
Single-Shot Sample Rate/Ch	80 GS/s on each channel.
Maximum Trigger Rate	1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
Intersegment Time	1 μs
Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments)	32 M / 32 M / 32M (1000)
Memory Options (4 Ch / 2 Ch / 1Ch) (Number of Segments)	S-32 Option: 32M / 32M / 32M (7,500) M-64 Option: 64M / 64M / 64M (15,000) L-128 Option: 128M / 128M / 128M (15,000) VL-256 Option: 256M / 256M / 256M (15,000) XL-512 Option: 512M / 512M / 512M (15,000)
Acquisition Processing
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
Enhanced Resolution (ERES)	From 8.5 to 11 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps
Interpolation	Linear or Sin x/x
Triggering System
Modes	Normal, Auto, Single, and Stop
Sources	Any Ch 1-4 (Edge, Window, SMART, Cascade triggers), AUX, internal Fast Edge; or any input channel (Edge trigger only) on additional 10-xxZi-A Acquisition Modules (Channels 5 and higher). Slope and level unique to each source except line trigger.
Coupling Mode	DC, AC, HFRej, LFRej
Pre-trigger Delay	0-100% of memory size (adjustable in 1% increments of 100 ns)
Post-trigger Delay	0-10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
Hold-off by Time or Events	From 2 ns up to 20 s or from 1 to 99,999,999 events
Internal Trigger Range	±4.1 div from center
Trigger Sensitivity with Edge Trigger (1.85/2.4/2.92mm Inputs)	For Ch 1-80 of a LabMaster 10 Zi-A system: 3 div @ ＜ 12 GHz 1.5 div @ ＜ 3 GHz 1.0 div @ ＜ 200 MHz (for DC coupling, ≧ 10 mV/div, 50 Ω)
External Trigger Sensitivity, (Edge Trigger)	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2 div @ ＜ 1 GHz, 1.5 div @ ＜ 500 MHz, 1.0 div @ ＜ 200 MHz, (for DC coupling)
Max. Trigger Frequency, SMART Trigger	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2.0 GHz @ ≧ 10 mV/div (minimum triggerable width 200 ps)
External Trigger Input Range	For any LabMaster 10xx-Zi-A Acquisition Module: Aux (±0.4 V) (Only Ch1-4 Acquisition Module has "active" AUX Input)
Basic Triggers
TV-Composite Video	Not available
High Speed Serial Protocol Triggering
Data Rates	Option LM10Zi-6GBIT-80B-8B10B-TD: 600 Mb/s to 6.5 Gb/s, Channel 4 input only Option LM10Zi-14GBIT-80B-8B10B-TD: 600 Mb/s to 14.1 Gb/s, Channel 4 input only
Pattern Length	80 bits NRZ, eight 8b/10b symbols
Clock and Data Outputs	No Clock and Data Recovery outputs provided
Measurement Trigger
Measurement Trigger Capability	0
Color Waveform Display
Type	On LabMaster MCM-Zi Master Control Module: Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
Resolution	WXGA; 1280 x 768 pixels.
Number of traces	Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces.
Grid Styles	Auto, Single, Dual, Triple, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Twelve, Sixteen. Up to twenty grids available with some software options.
Waveform Representation	Sample dots joined, or sample dots only
Internal Waveform Memory
Internal Waveform Memory	12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
Integrated Second Display
Type	Supports touch screen integration of user-supplied second display with split-grid capability. (Note: touch screen driver for second display may not be a Fujitsu driver)
Resolution	Determined by display chosen by user
LeCroy WaveStream Fast Viewing Mode
Intensity	256 Intensity Levels, 1-100% adjustable via front panel control
Types	Select analog or color-graded
Number of Channels	up to 80 simultaneously
Max Sampling Rate	80 GS/s
Persistence Aging	Select from 500 ms to Infinity
Waveforms/second (continuous)	up to 2500 Waveforms/second
Operation	Front panel toggle between WaveStream ON (Analog), ON (Color) and OFF
Analog Persistence Display
Analog and Color-Graded Persistence	Variable saturation levels; stores each trace's persistence data in memory
Persistence Types	Select analog, color, or three-dimensional
Trace Selection	Activate persistence on all or any combination of traces
Persistence Aging	Select from 500 ms to infinity
Sweep Display Modes	All accumulated, or all accumulated with last trace highlighted
High Speed Digitizer Output (Option)
Type	Option LSIB-2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
Transfer Rate	up to 325 MB/s (typical) - Maximum of 4 channels (consult Teledyne LeCroy for >4 channels)
Output Protocol	PCI Express, Gen 1 (4 lanes utilized for data transfer)
Control Protocol	TCP/IP
Command Set	Via Windows Automation, or via LeCroy Remote Command Set
Processor/CPU
Processor Memory	32 GB standard. Up to 192 GB optionally available.
Operating System	Microsoft WindowsR 7 Professional Edition (64-bit)
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 12 Zoom and 12 Math/Zoom traces
Setup Storage
Front Panel and Instrument Status	Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
Interface
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Class C (v1.2) Compliant
GPIB Port	Supports IEEE - 488.2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
LSIB Port (optional)	Supports PCIe Gen1 x4 protocol with LeCroy supplied API. Installs in LabMaster LabMaster MCM-Zi-A Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi-A Acquisition Module.
Ethernet Port	Supports 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Ports	LabMaster MCM-Zi -A Master Control Module: minimum 2 total USB 2.0 ports on rear of unit to support Windows compatible devices LabMaster MCM-Zi -A Master Control Module: minimum 3 total USB 2.0 ports on front of unit to support Windows compatible devices
External Monitor Port	Dual Link DVI compatible to support internal display on MCM-Zi Master Control Module (1280 x 768 pixel resolution) and customer-supplied monitor with up to WQXGA (2560 x 1600 pixel) resolution using extended desktop mode.
Auxiliary Input
Signal Types	For External Trigger Input. Located on every LabMaster 10-xxZi-A Acquisition Module (front-mounted BNC, 50 Ω). 10-xxZi-A Acquisition Module that is used for Channels 1-4 contains "active" AUX Input.
Coupling	50 Ω: DC
Max. Input Voltage	5 Vrms
Auxiliary Output
Signal Types	Select from calibrator, control signals or Off
Output Signal	500 Hz-5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0-1 V into 1 MΩ)
Control Signals	Trigger enabled, trigger out, pass/fail status, off
Connector Type	BNC, located on front of every LabMaster 10-xxZi Acquisition Module. 10-xxZi Acquisition Module that is used for Channels 1-4 contains "active" AUX Output.
Automatic Setup
Auto Setup	Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale	Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
General
Auto Calibration	Ensures specified DC and timing accuracy is maintained for 1 year minimum.
Probes
Probes	No passive probes supplied
Probe System	2.92mm interface automatically detects and supports a variety of compatible probes. Use L2.92A-PLINK or L2.92A-PBUS 2.92mm Probe Adapters to connect 50Ω ProLink or 50Ω ProBus compatible probes to 2.92mm interface.
Scale Factors	Automatically or manually selected depending on probe used
Calibration Output	MCM-Zi-A Master Control Module: Fast Edge output, 5MHz square wave, 350mVp-p (typical), 50ps rise time, output to SMA connector, AC Coupled
Power Requirements
Voltage	LabMaster 10-xxZi Acquisition Module: 100-240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection, Installation Category II LabMaster MCM-Zi Master Control Module: 100-240 VAC ±10% at 45-66 Hz; Automatic AC Voltage Selection, Installation Category II
Max. Power Consumption	LabMaster 10-xxZi-A Acquisition Module - 1225 W / 1225 VA. LabMaster MCM-Zi-A Master Control Module - 450 W / 450 VA. Each Module and the CPU has a separate power cord.
Environmental and Safety
Temperature (Operating)	+5 ℃ to +40 ℃
Temperature (Non-Operating)	-20 ℃ to +60 ℃
Humidity (Operating)	5% to 80% relative humidity (non-condensing) up to +31 ℃. Upper limit derates to 50% relative humidity (non-condensing) at +40 ℃.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +25 ℃
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Physical Dimensions
Dimensions (HWD)	LabMaster MCM-Zi-A Master Control Module - 10.9"H x 18.2"W x 15.6"D (277 x 462 x 396 mm), LabMaster 10-xxZi-A Acquisition Module - 8.0"H x 18.2"W x 26"D (202 x 462 x 660 mm)
Weight	LabMaster 10-xxZi-A Acquisition Module -53 lbs. (24.1 kg) LabMaster MCM-Zi-A Master Control Module - 47 lbs. (21.4 kg)
Shipping Weight	LabMaster 10-xxZi-A Acquisition Module -71 lbs. (32.3 kg) LabMaster MCM-Zi-A Master Control Module - 56 lbs. (25.5 kg)
Certifications
Certifications	CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, EN61010-2-030, UL 61010-1 3rd edition, and CSA C22.2 No. 61010-1-12
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.

LabMaster 10 Zi-A 30 GHz Systems 　スペック

Vertical System
Analog Bandwidth (Max)	30 GHz
Analog Bandwidth @ 50 Ω (-3 dB) (2.4/2.92mm Inputs)	30 GHz (≧5 mV/div)
Rise Time (10-90%, 50 Ω)	12.8 ps (test limit, flatness mode)
Rise Time (20-80%, 50 Ω)	9.6 ps (flatness mode)
Input Channels	Up to 80, depending on configuration selected. (Any combination of up to 80 2.92mm input channels)
Bandwidth Limiters	1, 3, 4, 6, 8, 13, 16, 20, 25 GHz
Input Impedance	2.92mm Inputs: 50 Ω+/-2%
Input Coupling	2.92 mm Inputs: 50 Ω: DC, GND
Maximum Input Voltage	2.92 mm Inputs: ±2 [email protected]＜76mV/div, [email protected]≧76mV/div
Channel-Channel Isolation	DC to 36 GHz: 60 dB (>1000:1) (For any two 2.92mm input channels, same or different v/div settings, typical)
Vertical Resolution	8 bits; up to 11 bits with enhanced resolution (ERES)
Sensitivity	50 Ω (2.92mm): 5 mV-500mV/div, fully variable (5-9.9 mV/div via zoom)
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	±1% F.S. (typical), offset at 0V; ±1.5% F.S. (test limit), offset at 0V
Offset Range	50 Ω: ±500 mV @ 5-75 mV/div ±4 V @ 76 mV/div -500mV/div
Offset Accuracy	50 Ω (2.92mm): 5 mV-500mV/div, fully variable (5-9.9 mV/div via zoom)
DC Vertical Offset Accuracy	±(1.5% of offset setting + 1.5% F.S. + 1 mV) (test limit)
Horizontal System
Timebases	Internal timebase with 10 GHz clock frequency common to all input channels. Single, distributed 10 GHz clock for all channels ensures precise synchronization with timing accuracy between all channels identical to that provided within a single, conventional oscilloscope package.
Time/Division Range	10 ps/div-256 s/div (maximum capture time is based on minimum sample rate of 200kS/s and installed memory).
Clock Accuracy	＜0.1 ppm + (aging of 0.05 ppm/yr from last calibration)
Sample Clock Jitter	up to 3.2ms Acquired Time Range: 50fsrms (Internal Timebase Reference) 50fsrms (External Timebase Reference) up to 6.4ms Acquired Time Range: 130fsrms (Internal Timebase Reference) 130fsrms (External Timebase Reference)
Delta Time Measurement Accuracy	√2*√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) (RMS)+(clock accuracy*reading)(seconds)
Jitter Measurement Floor	√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) secondsrms (TIE)
Jitter Between Channels	＜250fsrms (TIE, typical, measured at maximum bandwidth)
Trigger and Interpolator Jitter	＜0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware),
Channel-Channel Deskew Range	±9 x time/div. setting or 25 ns max. (whichever is larger), each channel
External Timebase Reference (Input)	10 MHz or 100MHz; 50 Ω impedance, applied at the rear input of MCM-Zi-A Master Control Module
External Timebase Reference (Output)	10 MHz or 100 MHz ; 50 Ω impedance, output at the rear of MCM-Zi-A Master Control Module
Acquisition System
Single-Shot Sample Rate/Ch	80 GS/s on each channel.
Maximum Trigger Rate	1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
Intersegment Time	1 μs
Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments)	32 M / 32 M / 32M (1000)
Memory Options (4 Ch / 2 Ch / 1Ch) (Number of Segments)	S-32 Option: 32M / 32M / 32M (7,500) M-64 Option: 64M / 64M / 64M (15,000) L-128 Option: 128M / 128M / 128M (15,000) VL-256 Option: 256M / 256M / 256M (15,000) XL-512 Option: 512M / 512M / 512M (15,000)
Acquisition Processing
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
Enhanced Resolution (ERES)	From 8.5 to 11 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps
Interpolation	Linear or Sin x/x
Triggering System
Modes	Normal, Auto, Single, and Stop
Sources	Any Ch 1-4 (Edge, Window, SMART, Cascade triggers), AUX, internal Fast Edge; or any input channel (Edge trigger only) on additional 10-xxZi-A Acquisition Modules (Channels 5 and higher). Slope and level unique to each source except line trigger.
Coupling Mode	DC, AC, HFRej, LFRej
Pre-trigger Delay	0-100% of memory size (adjustable in 1% increments of 100 ns)
Post-trigger Delay	0-10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
Hold-off by Time or Events	From 2 ns up to 20 s or from 1 to 99,999,999 events
Internal Trigger Range	±4.1 div from center
Trigger Sensitivity with Edge Trigger (1.85/2.4/2.92mm Inputs)	For Ch 1-80 of a LabMaster 10 Zi-A system: 3 div @ ＜ 12 GHz 1.5 div @ ＜ 3 GHz 1.0 div @ ＜ 200 MHz (for DC coupling, ≧ 10 mV/div, 50 Ω)
External Trigger Sensitivity, (Edge Trigger)	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2 div @ ＜ 1 GHz, 1.5 div @ ＜ 500 MHz, 1.0 div @ ＜ 200 MHz, (for DC coupling)
Max. Trigger Frequency, SMART Trigger	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2.0 GHz @ ≧ 10 mV/div (minimum triggerable width 200 ps)
External Trigger Input Range	For any LabMaster 10xx-Zi-A Acquisition Module: Aux (±0.4 V) (Only Ch1-4 Acquisition Module has "active" AUX Input)
Basic Triggers
TV-Composite Video	Not available
High Speed Serial Protocol Triggering
Data Rates	Option LM10Zi-6GBIT-80B-8B10B-TD: 600 Mb/s to 6.5 Gb/s, Channel 4 input only Option LM10Zi-14GBIT-80B-8B10B-TD: 600 Mb/s to 14.1 Gb/s, Channel 4 input only
Pattern Length	80 bits NRZ, eight 8b/10b symbols
Clock and Data Outputs	No Clock and Data Recovery outputs provided
Measurement Trigger
Measurement Trigger Capability	0
Color Waveform Display
Type	On LabMaster MCM-Zi Master Control Module: Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
Resolution	WXGA; 1280 x 768 pixels.
Number of traces	Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces.
Grid Styles	Auto, Single, Dual, Triple, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Twelve, Sixteen. Up to twenty grids available with some software options.
Waveform Representation	Sample dots joined, or sample dots only
Internal Waveform Memory
Internal Waveform Memory	12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
Integrated Second Display
Type	Supports touch screen integration of user-supplied second display with split-grid capability. (Note: touch screen driver for second display may not be a Fujitsu driver)
Resolution	Determined by display chosen by user
LeCroy WaveStream Fast Viewing Mode
Intensity	256 Intensity Levels, 1-100% adjustable via front panel control
Types	Select analog or color-graded
Number of Channels	up to 80 simultaneously
Max Sampling Rate	80 GS/s
Persistence Aging	Select from 500 ms to Infinity
Waveforms/second (continuous)	up to 2500 Waveforms/second
Operation	Front panel toggle between WaveStream ON (Analog), ON (Color) and OFF
Analog Persistence Display
Analog and Color-Graded Persistence	Variable saturation levels; stores each trace's persistence data in memory
Persistence Types	Select analog, color, or three-dimensional
Trace Selection	Activate persistence on all or any combination of traces
Persistence Aging	Select from 500 ms to infinity
Sweep Display Modes	All accumulated, or all accumulated with last trace highlighted
High Speed Digitizer Output (Option)
Type	Option LSIB-2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
Transfer Rate	up to 325 MB/s (typical) - Maximum of 4 channels (consult Teledyne LeCroy for >4 channels)
Output Protocol	PCI Express, Gen 1 (4 lanes utilized for data transfer)
Control Protocol	TCP/IP
Command Set	Via Windows Automation, or via LeCroy Remote Command Set
Processor/CPU
Processor Memory	32 GB standard. Up to 192 GB optionally available.
Operating System	Microsoft WindowsR 7 Professional Edition (64-bit)
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 12 Zoom and 12 Math/Zoom traces
Setup Storage
Front Panel and Instrument Status	Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
Interface
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Class C (v1.2) Compliant
GPIB Port	Supports IEEE - 488.2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
LSIB Port (optional)	Supports PCIe Gen1 x4 protocol with LeCroy supplied API. Installs in LabMaster LabMaster MCM-Zi-A Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi-A Acquisition Module.
Ethernet Port	Supports 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Ports	LabMaster MCM-Zi -A Master Control Module: minimum 2 total USB 2.0 ports on rear of unit to support Windows compatible devices LabMaster MCM-Zi -A Master Control Module: minimum 3 total USB 2.0 ports on front of unit to support Windows compatible devices
External Monitor Port	Dual Link DVI compatible to support internal display on MCM-Zi Master Control Module (1280 x 768 pixel resolution) and customer-supplied monitor with up to WQXGA (2560 x 1600 pixel) resolution using extended desktop mode.
Auxiliary Input
Signal Types	For External Trigger Input. Located on every LabMaster 10-xxZi-A Acquisition Module (front-mounted BNC, 50 Ω). 10-xxZi-A Acquisition Module that is used for Channels 1-4 contains "active" AUX Input.
Coupling	50 Ω: DC
Max. Input Voltage	5 Vrms
Auxiliary Output
Signal Types	Select from calibrator, control signals or Off
Output Signal	500 Hz-5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0-1 V into 1 MΩ)
Control Signals	Trigger enabled, trigger out, pass/fail status, off
Connector Type	BNC, located on front of every LabMaster 10-xxZi Acquisition Module. 10-xxZi Acquisition Module that is used for Channels 1-4 contains "active" AUX Output.
Automatic Setup
Auto Setup	Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale	Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
General
Auto Calibration	Ensures specified DC and timing accuracy is maintained for 1 year minimum.
Probes
Probes	No passive probes supplied
Probe System	2.92mm interface automatically detects and supports a variety of compatible probes. Use L2.92A-PLINK or L2.92A-PBUS 2.92mm Probe Adapters to connect 50Ω ProLink or 50Ω ProBus compatible probes to 2.92mm interface.
Scale Factors	Automatically or manually selected depending on probe used
Calibration Output	MCM-Zi-A Master Control Module: Fast Edge output, 5MHz square wave, 350mVp-p (typical), 50ps rise time, output to SMA connector, AC Coupled
Power Requirements
Voltage	LabMaster 10-xxZi Acquisition Module: 100-240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection, Installation Category II LabMaster MCM-Zi Master Control Module: 100-240 VAC ±10% at 45-66 Hz; Automatic AC Voltage Selection, Installation Category II
Max. Power Consumption	LabMaster 10-xxZi-A Acquisition Module - 1225 W / 1225 VA. LabMaster MCM-Zi-A Master Control Module - 450 W / 450 VA. Each Module and the CPU has a separate power cord.
Environmental and Safety
Temperature (Operating)	+5 ℃ to +40 ℃
Temperature (Non-Operating)	-20 ℃ to +60 ℃
Humidity (Operating)	5% to 80% relative humidity (non-condensing) up to +31 ℃. Upper limit derates to 50% relative humidity (non-condensing) at +40 ℃.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +25 ℃
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Physical Dimensions
Dimensions (HWD)	LabMaster MCM-Zi-A Master Control Module - 10.9"H x 18.2"W x 15.6"D (277 x 462 x 396 mm), LabMaster 10-xxZi-A Acquisition Module - 8.0"H x 18.2"W x 26"D (202 x 462 x 660 mm)
Weight	LabMaster 10-xxZi-A Acquisition Module -53 lbs. (24.1 kg) LabMaster MCM-Zi-A Master Control Module - 47 lbs. (21.4 kg)
Shipping Weight	LabMaster 10-xxZi-A Acquisition Module -71 lbs. (32.3 kg) LabMaster MCM-Zi-A Master Control Module - 56 lbs. (25.5 kg)
Certifications
Certifications	CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, EN61010-2-030, UL 61010-1 3rd edition, and CSA C22.2 No. 61010-1-12
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.

LabMaster 10 Zi-A 36 GHz Systems 　スペック

Vertical System
Analog Bandwidth (Max)	36 GHz
Analog Bandwidth @ 50 Ω (-3 dB) (2.4/2.92mm Inputs)	36 GHz (≧5 mV/div)
Rise Time (10-90%, 50 Ω)	10.7 ps (test limit, flatness mode)
Rise Time (20-80%, 50 Ω)	8.0 ps (flatness mode)
Input Channels	Up to 80, depending on configuration selected. (Any combination of up to 80 2.92mm input channels)
Bandwidth Limiters	1, 3, 4, 6, 8, 13, 16, 20, 25, 30, 33 GHz
Input Impedance	2.92mm Inputs: 50 Ω+/-2%
Input Coupling	2.92 mm Inputs: 50 Ω: DC, GND
Maximum Input Voltage	2.92 mm Inputs: ±2 [email protected]＜76mV/div, [email protected]≧76mV/div
Channel-Channel Isolation	DC to 36 GHz: 60 dB (>1000:1) (For any two 2.92mm input channels, same or different v/div settings, typical)
Vertical Resolution	8 bits; up to 11 bits with enhanced resolution (ERES)
Sensitivity	50 Ω (2.92mm): 5 mV-500mV/div, fully variable (5-9.9 mV/div via zoom)
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	±1% F.S. (typical), offset at 0V; ±1.5% F.S. (test limit), offset at 0V
Offset Range	50 Ω: ±500 mV @ 5-75 mV/div ±4 V @ 76 mV/div -500mV/div
Offset Accuracy	50 Ω (2.92mm): 5 mV-500mV/div, fully variable (5-9.9 mV/div via zoom)
DC Vertical Offset Accuracy	±(1.5% of offset setting + 1.5% F.S. + 1 mV) (test limit)
Horizontal System
Timebases	Internal timebase with 10 GHz clock frequency common to all input channels. Single, distributed 10 GHz clock for all channels ensures precise synchronization with timing accuracy between all channels identical to that provided within a single, conventional oscilloscope package.
Time/Division Range	10 ps/div-256 s/div (maximum capture time is based on minimum sample rate of 200kS/s and installed memory).
Clock Accuracy	＜0.1 ppm + (aging of 0.05 ppm/yr from last calibration)
Sample Clock Jitter	up to 3.2ms Acquired Time Range: 50fsrms (Internal Timebase Reference) 50fsrms (External Timebase Reference) up to 6.4ms Acquired Time Range: 130fsrms (Internal Timebase Reference) 130fsrms (External Timebase Reference)
Delta Time Measurement Accuracy	√2*√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) (RMS)+(clock accuracy*reading)(seconds)
Jitter Measurement Floor	√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) secondsrms (TIE)
Jitter Between Channels	＜250fsrms (TIE, typical, measured at maximum bandwidth)
Trigger and Interpolator Jitter	＜0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware),
Channel-Channel Deskew Range	±9 x time/div. setting or 25 ns max. (whichever is larger), each channel
External Timebase Reference (Input)	10 MHz or 100MHz; 50 Ω impedance, applied at the rear input of MCM-Zi-A Master Control Module
External Timebase Reference (Output)	10 MHz or 100 MHz ; 50 Ω impedance, output at the rear of MCM-Zi-A Master Control Module
Acquisition System
Single-Shot Sample Rate/Ch	80 GS/s on each channel.
Maximum Trigger Rate	1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
Intersegment Time	1 μs
Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments)	32 M / 32 M / 32M (1000)
Memory Options (4 Ch / 2 Ch / 1Ch) (Number of Segments)	S-32 Option: 32M / 32M / 32M (7,500) M-64 Option: 64M / 64M / 64M (15,000) L-128 Option: 128M / 128M / 128M (15,000) VL-256 Option: 256M / 256M / 256M (15,000) XL-512 Option: 512M / 512M / 512M (15,000)
Acquisition Processing
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
Enhanced Resolution (ERES)	From 8.5 to 11 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps
Interpolation	Linear or Sin x/x
Triggering System
Modes	Normal, Auto, Single, and Stop
Sources	Any Ch 1-4 (Edge, Window, SMART, Cascade triggers), AUX, internal Fast Edge; or any input channel (Edge trigger only) on additional 10-xxZi-A Acquisition Modules (Channels 5 and higher). Slope and level unique to each source except line trigger.
Coupling Mode	DC, AC, HFRej, LFRej
Pre-trigger Delay	0-100% of memory size (adjustable in 1% increments of 100 ns)
Post-trigger Delay	0-10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
Hold-off by Time or Events	From 2 ns up to 20 s or from 1 to 99,999,999 events
Internal Trigger Range	±4.1 div from center
Trigger Sensitivity with Edge Trigger (1.85/2.4/2.92mm Inputs)	For Ch 1-80 of a LabMaster 10 Zi-A system: 3 div @ ＜ 12 GHz 1.5 div @ ＜ 3 GHz 1.0 div @ ＜ 200 MHz (for DC coupling, ≧ 10 mV/div, 50 Ω)
External Trigger Sensitivity, (Edge Trigger)	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2 div @ ＜ 1 GHz, 1.5 div @ ＜ 500 MHz, 1.0 div @ ＜ 200 MHz, (for DC coupling)
Max. Trigger Frequency, SMART Trigger	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2.0 GHz @ ≧ 10 mV/div (minimum triggerable width 200 ps)
External Trigger Input Range	For any LabMaster 10xx-Zi-A Acquisition Module: Aux (±0.4 V) (Only Ch1-4 Acquisition Module has "active" AUX Input)
Basic Triggers
TV-Composite Video	Not available
High Speed Serial Protocol Triggering
Data Rates	Option LM10Zi-6GBIT-80B-8B10B-TD: 600 Mb/s to 6.5 Gb/s, Channel 4 input only Option LM10Zi-14GBIT-80B-8B10B-TD: 600 Mb/s to 14.1 Gb/s, Channel 4 input only
Pattern Length	80 bits NRZ, eight 8b/10b symbols
Clock and Data Outputs	No Clock and Data Recovery outputs provided
Measurement Trigger
Measurement Trigger Capability	0
Color Waveform Display
Type	On LabMaster MCM-Zi Master Control Module: Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
Resolution	WXGA; 1280 x 768 pixels.
Number of traces	Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces.
Grid Styles	Auto, Single, Dual, Triple, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Twelve, Sixteen. Up to twenty grids available with some software options.
Waveform Representation	Sample dots joined, or sample dots only
Internal Waveform Memory
Internal Waveform Memory	12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
Integrated Second Display
Type	Supports touch screen integration of user-supplied second display with split-grid capability. (Note: touch screen driver for second display may not be a Fujitsu driver)
Resolution	Determined by display chosen by user
LeCroy WaveStream Fast Viewing Mode
Intensity	256 Intensity Levels, 1-100% adjustable via front panel control
Types	Select analog or color-graded
Number of Channels	up to 80 simultaneously
Max Sampling Rate	80 GS/s
Persistence Aging	Select from 500 ms to Infinity
Waveforms/second (continuous)	up to 2500 Waveforms/second
Operation	Front panel toggle between WaveStream ON (Analog), ON (Color) and OFF
Analog Persistence Display
Analog and Color-Graded Persistence	Variable saturation levels; stores each trace's persistence data in memory
Persistence Types	Select analog, color, or three-dimensional
Trace Selection	Activate persistence on all or any combination of traces
Persistence Aging	Select from 500 ms to infinity
Sweep Display Modes	All accumulated, or all accumulated with last trace highlighted
High Speed Digitizer Output (Option)
Type	Option LSIB-2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
Transfer Rate	up to 325 MB/s (typical) - Maximum of 4 channels (consult Teledyne LeCroy for >4 channels)
Output Protocol	PCI Express, Gen 1 (4 lanes utilized for data transfer)
Control Protocol	TCP/IP
Command Set	Via Windows Automation, or via LeCroy Remote Command Set
Processor/CPU
Processor Memory	32 GB standard. Up to 192 GB optionally available.
Operating System	Microsoft WindowsR 7 Professional Edition (64-bit)
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 12 Zoom and 12 Math/Zoom traces
Setup Storage
Front Panel and Instrument Status	Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
Interface
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Class C (v1.2) Compliant
GPIB Port	Supports IEEE - 488.2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
LSIB Port (optional)	Supports PCIe Gen1 x4 protocol with LeCroy supplied API. Installs in LabMaster LabMaster MCM-Zi-A Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi-A Acquisition Module.
Ethernet Port	Supports 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Ports	LabMaster MCM-Zi -A Master Control Module: minimum 2 total USB 2.0 ports on rear of unit to support Windows compatible devices LabMaster MCM-Zi -A Master Control Module: minimum 3 total USB 2.0 ports on front of unit to support Windows compatible devices
External Monitor Port	Dual Link DVI compatible to support internal display on MCM-Zi Master Control Module (1280 x 768 pixel resolution) and customer-supplied monitor with up to WQXGA (2560 x 1600 pixel) resolution using extended desktop mode.
Auxiliary Input
Signal Types	For External Trigger Input. Located on every LabMaster 10-xxZi-A Acquisition Module (front-mounted BNC, 50 Ω). 10-xxZi-A Acquisition Module that is used for Channels 1-4 contains "active" AUX Input.
Coupling	50 Ω: DC
Max. Input Voltage	5 Vrms
Auxiliary Output
Signal Types	Select from calibrator, control signals or Off
Output Signal	500 Hz-5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0-1 V into 1 MΩ)
Control Signals	Trigger enabled, trigger out, pass/fail status, off
Connector Type	BNC, located on front of every LabMaster 10-xxZi Acquisition Module. 10-xxZi Acquisition Module that is used for Channels 1-4 contains "active" AUX Output.
Automatic Setup
Auto Setup	Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale	Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
General
Auto Calibration	Ensures specified DC and timing accuracy is maintained for 1 year minimum.
Probes
Probes	No passive probes supplied
Probe System	2.92mm interface automatically detects and supports a variety of compatible probes. Use L2.92A-PLINK or L2.92A-PBUS 2.92mm Probe Adapters to connect 50Ω ProLink or 50Ω ProBus compatible probes to 2.92mm interface.
Scale Factors	Automatically or manually selected depending on probe used
Calibration Output	MCM-Zi-A Master Control Module: Fast Edge output, 5MHz square wave, 350mVp-p (typical), 50ps rise time, output to SMA connector, AC Coupled
Power Requirements
Voltage	LabMaster 10-xxZi Acquisition Module: 100-240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection, Installation Category II LabMaster MCM-Zi Master Control Module: 100-240 VAC ±10% at 45-66 Hz; Automatic AC Voltage Selection, Installation Category II
Max. Power Consumption	LabMaster 10-xxZi-A Acquisition Module - 1225 W / 1225 VA. LabMaster MCM-Zi-A Master Control Module - 450 W / 450 VA. Each Module and the CPU has a separate power cord.
Environmental and Safety
Temperature (Operating)	+5 ℃ to +40 ℃
Temperature (Non-Operating)	-20 ℃ to +60 ℃
Humidity (Operating)	5% to 80% relative humidity (non-condensing) up to +31 ℃. Upper limit derates to 50% relative humidity (non-condensing) at +40 ℃.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +25 ℃
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Physical Dimensions
Dimensions (HWD)	LabMaster MCM-Zi-A Master Control Module - 10.9"H x 18.2"W x 15.6"D (277 x 462 x 396 mm), LabMaster 10-xxZi-A Acquisition Module - 8.0"H x 18.2"W x 26"D (202 x 462 x 660 mm)
Weight	LabMaster 10-xxZi-A Acquisition Module -53 lbs. (24.1 kg) LabMaster MCM-Zi-A Master Control Module - 47 lbs. (21.4 kg)
Shipping Weight	LabMaster 10-xxZi-A Acquisition Module -71 lbs. (32.3 kg) LabMaster MCM-Zi-A Master Control Module - 56 lbs. (25.5 kg)
Certifications
Certifications	CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, EN61010-2-030, UL 61010-1 3rd edition, and CSA C22.2 No. 61010-1-12
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.

LabMaster 10 Zi-A 50 GHz Systems 　スペック

Vertical System
Analog Bandwidth (Max)	50 GHz
Analog Bandwidth @ 50 Ω (-3 dB) (1.85mm Inputs)	50 GHz (≧10 mV/div)
Analog Bandwidth @ 50 Ω (-3 dB) (2.4/2.92mm Inputs)	36 GHz (≧5 mV/div)
Rise Time (10-90%, 50 Ω)	8 ps (test limit, flatness mode)
Rise Time (20-80%, 50 Ω)	6 ps (flatness mode)
Input Channels	Up to 40, depending on configuration selected. Up to 80 @ 36 GHz.
Bandwidth Limiters	For ? 36 GHz Mode: 1, 3, 4, 6, 8, 13, 16, 20, 25, 30, 33 GHz. For > 36 GHz Mode: None.
Input Impedance	2.92mm Inputs: 50 Ω+/-2% 1.85mm Inputs: 50 Ω+/-2%
Input Coupling	2.92 mm Inputs: 50 Ω: DC, GND 1.85 mm Inputs: 50 Ω: DC
Maximum Input Voltage	2.92 mm Inputs: ±2 [email protected]＜76mV/div, [email protected]≧76mV/div 1.85 mm Inputs: ±2 [email protected]?80mV/div
Channel-Channel Isolation	DC to 36 GHz: 60 dB (>1000:1) (For any two 2.92mm input channels, same or different v/div settings, typical) 36 to 65 GHz: 40 dB (>100:1) (For any two 1.85mm input channels, same or different v/div settings, typical)
Vertical Resolution	8 bits; up to 11 bits with enhanced resolution (ERES)
Sensitivity	50 Ω (2.92mm): 5 mV-500mV/div, fully variable (5-9.9 mV/div via zoom) 50 Ω (1.85mm): 10 mV-80mV/div, fully variable. Higher gain settings possible through use of external attenuators.
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	±1% F.S. (typical), offset at 0V; ±1.5% F.S. (test limit), offset at 0V
Offset Range	50 Ω (1.85 mm): ±500 mV @ 10-80 mV/div 50 Ω (2.92mm): ±500 mV @ 5-75 mV/div ±4 V @ 76 mV/div -500mV/div
Offset Accuracy	50 Ω (2.92mm): 5 mV?500mV/div, fully variable (5-9.9 mV/div via zoom) 50 Ω (1.85mm): 10 mV?80mV/div, fully variable. Higher gain settings possible through use of external attenuators.
DC Vertical Offset Accuracy	±(1.5% of offset setting + 1.5% F.S. + 1 mV) (test limit)
Horizontal System
Timebases	Internal timebase with 10 GHz clock frequency common to all input channels. Single, distributed 10 GHz clock for all channels ensures precise synchronization with timing accuracy between all channels identical to that provided within a single, conventional oscilloscope package.
Time/Division Range	For >36 GHz Mode: 10 ps/div - 320 μs/div (maximum capture time is based on 160 GS/s and installed memory). For ?36 GHz Mode: 10 ps/div-256 s/div (maximum capture time is based on minimum sample rate of 200kS/s and installed memory).
Clock Accuracy	＜0.1 ppm + (aging of 0.05 ppm/yr from last calibration)
Sample Clock Jitter	up to 3.2ms Acquired Time Range: 50fsrms (Internal Timebase Reference) 50fsrms (External Timebase Reference) up to 6.4ms Acquired Time Range: 130fsrms (Internal Timebase Reference) 130fsrms (External Timebase Reference)
Delta Time Measurement Accuracy	√2*√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) (RMS)+(clock accuracy*reading)(seconds)
Jitter Measurement Floor	√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) secondsrms (TIE)
Jitter Between Channels	＜190fsrms (TIE, typical, measured at maximum bandwidth)
Trigger and Interpolator Jitter	＜0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware),
Channel-Channel Deskew Range	±9 x time/div. setting or 25 ns max. (whichever is larger), each channel
External Timebase Reference (Input)	10 MHz or 100MHz; 50 Ω impedance, applied at the rear input of MCM-Zi-A Master Control Module
External Timebase Reference (Output)	10 MHz or 100 MHz ; 50 Ω impedance, output at the rear of MCM-Zi-A Master Control Module
Acquisition System
Single-Shot Sample Rate/Ch	160 GS/s on each channel in >36 GHz Mode. 80 GS/s on each channel in ?36 GHz Mode.
Maximum Trigger Rate	1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
Intersegment Time	1 μs
Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments)	64 M / 64 M / 64 M (In ?36 GHz Modes, reference memory specification for 36 GHz LabMasters) (1000)
Memory Options (4 Ch / 2 Ch / 1Ch) (Number of Segments)	S-32 Option: 64M / 64M / 64M (3,500) M-64 Option: 128M / 128M / 128M (7,500) L-128 Option: 256M / 256M / 256M (15,000) VL-256 Option: 512M / 512M / 512M (15,000) XL-512 Option: 1024M / 1024M / 1024M (15,000) (In ?36 GHz Modes, reference memory specification for LabMaster 10 Zi-A 36 GHz Systems)
Acquisition Processing
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
Enhanced Resolution (ERES)	From 8.5 to 11 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps
Interpolation	Linear or Sin x/x
Triggering System
Modes	Normal, Auto, Single, and Stop
Sources	Any Ch 1-4 (Edge, Window, SMART, Cascade triggers), AUX, internal Fast Edge; or any input channel (Edge trigger only) on additional 10-xxZi-A Acquisition Modules (Channels 5 and higher). Slope and level unique to each source except line trigger.
Coupling Mode	DC, AC, HFRej, LFRej
Pre-trigger Delay	0-100% of memory size (adjustable in 1% increments of 100 ns)
Post-trigger Delay	0-10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
Hold-off by Time or Events	From 2 ns up to 20 s or from 1 to 99,999,999 events
Internal Trigger Range	±4.1 div from center
Trigger Sensitivity with Edge Trigger (1.85/2.4/2.92mm Inputs)	For Ch 1-80 of a LabMaster 10 Zi-A system: 3 div @ ＜ 12 GHz 1.5 div @ ＜ 3 GHz 1.0 div @ ＜ 200 MHz (for DC coupling, ≧ 10 mV/div, 50 Ω)
External Trigger Sensitivity, (Edge Trigger)	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2 div @ ＜ 1 GHz, 1.5 div @ ＜ 500 MHz, 1.0 div @ ＜ 200 MHz, (for DC coupling)
Max. Trigger Frequency, SMART Trigger	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2.0 GHz @ ≧ 10 mV/div (minimum triggerable width 200 ps)
External Trigger Input Range	For any LabMaster 10xx-Zi-A Acquisition Module: Aux (±0.4 V) (Only Ch1-4 Acquisition Module has "active" AUX Input)
Basic Triggers
TV-Composite Video	Not available
High Speed Serial Protocol Triggering
Data Rates	Option LM10Zi-6GBIT-80B-8B10B-TD: 600 Mb/s to 6.5 Gb/s, Channel 4 input only Option LM10Zi-14GBIT-80B-8B10B-TD: 600 Mb/s to 14.1 Gb/s, Channel 4 input only (Note: Channel 3 input will capture signal for triggering when oscilloscope is in ≧25 GHz mode)
Pattern Length	80 bits NRZ, eight 8b/10b symbols
Clock and Data Outputs	No Clock and Data Recovery outputs provided
Measurement Trigger
Measurement Trigger Capability	0
Color Waveform Display
Type	On LabMaster MCM-Zi Master Control Module: Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
Resolution	WXGA; 1280 x 768 pixels.
Number of traces	Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces.
Grid Styles	Auto, Single, Dual, Triple, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Twelve, Sixteen. Up to twenty grids available with some software options.
Waveform Representation	Sample dots joined, or sample dots only
Internal Waveform Memory
Internal Waveform Memory	12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
Integrated Second Display
Type	Supports touch screen integration of user-supplied second display with split-grid capability. (Note: touch screen driver for second display may not be a Fujitsu driver)
Resolution	Determined by display chosen by user
LeCroy WaveStream Fast Viewing Mode
Intensity	256 Intensity Levels, 1-100% adjustable via front panel control
Types	Select analog or color-graded
Number of Channels	up to 80 simultaneously
Max Sampling Rate	160GS/s
Persistence Aging	Select from 500 ms to Infinity
Waveforms/second (continuous)	up to 2500 Waveforms/second
Operation	Front panel toggle between WaveStream ON (Analog), ON (Color) and OFF
Analog Persistence Display
Analog and Color-Graded Persistence	Variable saturation levels; stores each trace's persistence data in memory
Persistence Types	Select analog, color, or three-dimensional
Trace Selection	Activate persistence on all or any combination of traces
Persistence Aging	Select from 500 ms to infinity
Sweep Display Modes	All accumulated, or all accumulated with last trace highlighted
High Speed Digitizer Output (Option)
Type	Option LSIB-2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
Transfer Rate	up to 325 MB/s (typical) - Maximum of 4 channels (consult Teledyne LeCroy for >4 channels)
Output Protocol	PCI Express, Gen 1 (4 lanes utilized for data transfer)
Control Protocol	TCP/IP
Command Set	Via Windows Automation, or via LeCroy Remote Command Set
Processor/CPU
Processor Memory	32 GB standard. Up to 192 GB optionally available.
Operating System	Microsoft WindowsR 7 Professional Edition (64-bit)
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 12 Zoom and 12 Math/Zoom traces
Setup Storage
Front Panel and Instrument Status	Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
Interface
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Class C (v1.2) Compliant
GPIB Port	Supports IEEE - 488.2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
LSIB Port (optional)	Supports PCIe Gen1 x4 protocol with LeCroy supplied API. Installs in LabMaster LabMaster MCM-Zi-A Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi-A Acquisition Module.
Ethernet Port	Supports 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Ports	LabMaster MCM-Zi -A Master Control Module: minimum 2 total USB 2.0 ports on rear of unit to support Windows compatible devices LabMaster MCM-Zi -A Master Control Module: minimum 3 total USB 2.0 ports on front of unit to support Windows compatible devices
External Monitor Port	Dual Link DVI compatible to support internal display on MCM-Zi Master Control Module (1280 x 768 pixel resolution) and customer-supplied monitor with up to WQXGA (2560 x 1600 pixel) resolution using extended desktop mode.
Auxiliary Input
Signal Types	For External Trigger Input. Located on every LabMaster 10-xxZi-A Acquisition Module (front-mounted BNC, 50 Ω). 10-xxZi-A Acquisition Module that is used for Channels 1-4 contains "active" AUX Input.
Coupling	50 Ω: DC
Max. Input Voltage	5 Vrms
Auxiliary Output
Signal Types	Select from calibrator, control signals or Off
Output Signal	500 Hz-5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0-1 V into 1 MΩ)
Control Signals	Trigger enabled, trigger out, pass/fail status, off
Connector Type	BNC, located on front of every LabMaster 10-xxZi Acquisition Module. 10-xxZi Acquisition Module that is used for Channels 1-4 contains "active" AUX Output.
Automatic Setup
Auto Setup	Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale	Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
General
Auto Calibration	Ensures specified DC and timing accuracy is maintained for 1 year minimum.
Probes
Probes	No passive probes supplied
Probe System	Up to 36 GHz Inputs: 2.92mm interface. Up to 65 GHz Inputs: 1.85mm interface 2.92mm interface automatically detects and supports a variety of compatible probes. Use L2.92A-PLINK or L2.92A-PBUS 2.92mm Probe Adapters to connect 50Ω ProLink or ProBus compatible probes to 2.92mm interface.
Scale Factors	Automatically or manually selected depending on probe used
Calibration Output	MCM-Zi-A Master Control Module: Fast Edge output, 5MHz square wave, 350mVp-p (typical), 50ps rise time, output to SMA connector, AC Coupled
Power Requirements
Voltage	LabMaster 10-xxZi Acquisition Module: 100-240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection, Installation Category II LabMaster MCM-Zi Master Control Module: 100-240 VAC ±10% at 45-66 Hz; Automatic AC Voltage Selection, Installation Category II
Max. Power Consumption	LabMaster 10-xxZi-A Acquisition Module - 1275 W / 1275 VA. LabMaster MCM-Zi-A Master Control Module - 450 W / 450 VA. Each Module and the CPU has a separate power cord.
Environmental and Safety
Temperature (Operating)	+5 ℃ to +40 ℃
Temperature (Non-Operating)	-20 ℃ to +60 ℃
Humidity (Operating)	5% to 80% relative humidity (non-condensing) up to +31 ℃. Upper limit derates to 50% relative humidity (non-condensing) at +40 ℃.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +25 ℃
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Physical Dimensions
Dimensions (HWD)	LabMaster MCM-Zi-A Master Control Module - 10.9"H x 18.2"W x 15.6"D (277 x 462 x 396 mm), LabMaster 10-xxZi-A Acquisition Module - 8.0"H x 18.2"W x 26"D (202 x 462 x 660 mm)
Weight	LabMaster 10-xxZi-A Acquisition Module -58 lbs. (26.4 kg) LabMaster MCM-Zi-A Master Control Module - 47 lbs. (21.4 kg)
Shipping Weight	LabMaster 10-xxZi-A Acquisition Module -76 lbs. (34.5 kg) LabMaster MCM-Zi-A Master Control Module - 56 lbs. (25.5 kg)
Certifications
Certifications	CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, EN61010-2-030, UL 61010-1 3rd edition, and CSA C22.2 No. 61010-1-12
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.

LabMaster 10 Zi-A 59 GHz Systems 　スペック

Vertical System
Analog Bandwidth (Max)	59 GHz
Analog Bandwidth @ 50 Ω (-3 dB) (1.85mm Inputs)	59 GHz (≧10 mV/div)
Analog Bandwidth @ 50 Ω (-3 dB) (2.4/2.92mm Inputs)	36 GHz (≧5 mV/div)
Rise Time (10-90%, 50 Ω)	6.9 ps (test limit, flatness mode)
Rise Time (20-80%, 50 Ω)	5.2 ps (flatness mode)
Input Channels	Up to 40, depending on configuration selected. Up to 80 @ 36 GHz.
Bandwidth Limiters	For ? 36 GHz Mode: 1, 3, 4, 6, 8, 13, 16, 20, 25, 30, 33 GHz. For > 36 GHz Mode: 50 GHz.
Input Impedance	2.92mm Inputs: 50 Ω+/-2% 1.85mm Inputs: 50 Ω+/-2%
Input Coupling	2.92 mm Inputs: 50 Ω: DC, GND 1.85 mm Inputs: 50 Ω: DC
Maximum Input Voltage	2.92 mm Inputs: ±2 [email protected]＜76mV/div, [email protected]≧76mV/div 1.85 mm Inputs: ±2 [email protected]?80mV/div
Channel-Channel Isolation	DC to 36 GHz: 60 dB (>1000:1) (For any two 2.92mm input channels, same or different v/div settings, typical) 36 to 65 GHz: 40 dB (>100:1) (For any two 1.85mm input channels, same or different v/div settings, typical)
Vertical Resolution	8 bits; up to 11 bits with enhanced resolution (ERES)
Sensitivity	50 Ω (2.92mm): 5 mV-500mV/div, fully variable (5-9.9 mV/div via zoom) 50 Ω (1.85mm): 10 mV-80mV/div, fully variable. Higher gain settings possible through use of external attenuators.
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	±1% F.S. (typical), offset at 0V; ±1.5% F.S. (test limit), offset at 0V
Offset Range	50 Ω (1.85 mm): ±500 mV @ 10-80 mV/div 50 Ω (2.92mm): ±500 mV @ 5-75 mV/div ±4 V @ 76 mV/div -500mV/div
Offset Accuracy	50 Ω (2.92mm): 5 mV?500mV/div, fully variable (5-9.9 mV/div via zoom) 50 Ω (1.85mm): 10 mV?80mV/div, fully variable. Higher gain settings possible through use of external attenuators.
DC Vertical Offset Accuracy	±(1.5% of offset setting + 1.5% F.S. + 1 mV) (test limit)
Horizontal System
Timebases	Internal timebase with 10 GHz clock frequency common to all input channels. Single, distributed 10 GHz clock for all channels ensures precise synchronization with timing accuracy between all channels identical to that provided within a single, conventional oscilloscope package.
Time/Division Range	For >36 GHz Mode: 10 ps/div - 320 μs/div (maximum capture time is based on 160 GS/s and installed memory). For ?36 GHz Mode: 10 ps/div-256 s/div (maximum capture time is based on minimum sample rate of 200kS/s and installed memory).
Clock Accuracy	＜0.1 ppm + (aging of 0.05 ppm/yr from last calibration)
Sample Clock Jitter	up to 3.2ms Acquired Time Range: 50fsrms (Internal Timebase Reference) 50fsrms (External Timebase Reference) up to 6.4ms Acquired Time Range: 130fsrms (Internal Timebase Reference) 130fsrms (External Timebase Reference)
Delta Time Measurement Accuracy	√2*√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) (RMS)+(clock accuracy*reading)(seconds)
Jitter Measurement Floor	√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) secondsrms (TIE)
Jitter Between Channels	＜150fsrms (TIE, typical, measured at maximum bandwidth)
Trigger and Interpolator Jitter	＜0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware),
Channel-Channel Deskew Range	±9 x time/div. setting or 25 ns max. (whichever is larger), each channel
External Timebase Reference (Input)	10 MHz or 100MHz; 50 Ω impedance, applied at the rear input of MCM-Zi-A Master Control Module
External Timebase Reference (Output)	10 MHz or 100 MHz ; 50 Ω impedance, output at the rear of MCM-Zi-A Master Control Module
Acquisition System
Single-Shot Sample Rate/Ch	160 GS/s on each channel in >36 GHz Mode. 80 GS/s on each channel in ?36 GHz Mode.
Maximum Trigger Rate	1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
Intersegment Time	1 μs
Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments)	64 M / 64 M / 64 M (In ?36 GHz Modes, reference memory specification for 36 GHz LabMasters) (1000)
Memory Options (4 Ch / 2 Ch / 1Ch) (Number of Segments)	S-32 Option: 64M / 64M / 64M (3,500) M-64 Option: 128M / 128M / 128M (7,500) L-128 Option: 256M / 256M / 256M (15,000) VL-256 Option: 512M / 512M / 512M (15,000) XL-512 Option: 1024M / 1024M / 1024M (15,000) (In ?36 GHz Modes, reference memory specification for LabMaster 10 Zi-A 36 GHz Systems)
Acquisition Processing
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
Enhanced Resolution (ERES)	From 8.5 to 11 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps
Interpolation	Linear or Sin x/x
Triggering System
Modes	Normal, Auto, Single, and Stop
Sources	Any Ch 1-4 (Edge, Window, SMART, Cascade triggers), AUX, internal Fast Edge; or any input channel (Edge trigger only) on additional 10-xxZi-A Acquisition Modules (Channels 5 and higher). Slope and level unique to each source except line trigger.
Coupling Mode	DC, AC, HFRej, LFRej
Pre-trigger Delay	0-100% of memory size (adjustable in 1% increments of 100 ns)
Post-trigger Delay	0-10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
Hold-off by Time or Events	From 2 ns up to 20 s or from 1 to 99,999,999 events
Internal Trigger Range	±4.1 div from center
Trigger Sensitivity with Edge Trigger (1.85/2.4/2.92mm Inputs)	For Ch 1-80 of a LabMaster 10 Zi-A system: 3 div @ ＜ 12 GHz 1.5 div @ ＜ 3 GHz 1.0 div @ ＜ 200 MHz (for DC coupling, ≧ 10 mV/div, 50 Ω)
External Trigger Sensitivity, (Edge Trigger)	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2 div @ ＜ 1 GHz, 1.5 div @ ＜ 500 MHz, 1.0 div @ ＜ 200 MHz, (for DC coupling)
Max. Trigger Frequency, SMART Trigger	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2.0 GHz @ ≧ 10 mV/div (minimum triggerable width 200 ps)
External Trigger Input Range	For any LabMaster 10xx-Zi-A Acquisition Module: Aux (±0.4 V) (Only Ch1-4 Acquisition Module has "active" AUX Input)
Basic Triggers
TV-Composite Video	Not available
High Speed Serial Protocol Triggering
Data Rates	Option LM10Zi-6GBIT-80B-8B10B-TD: 600 Mb/s to 6.5 Gb/s, Channel 4 input only Option LM10Zi-14GBIT-80B-8B10B-TD: 600 Mb/s to 14.1 Gb/s, Channel 4 input only (Note: Channel 3 input will capture signal for triggering when oscilloscope is in ≧25 GHz mode)
Pattern Length	80 bits NRZ, eight 8b/10b symbols
Clock and Data Outputs	No Clock and Data Recovery outputs provided
Measurement Trigger
Measurement Trigger Capability	0
Color Waveform Display
Type	On LabMaster MCM-Zi Master Control Module: Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
Resolution	WXGA; 1280 x 768 pixels.
Number of traces	Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces.
Grid Styles	Auto, Single, Dual, Triple, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Twelve, Sixteen. Up to twenty grids available with some software options.
Waveform Representation	Sample dots joined, or sample dots only
Internal Waveform Memory
Internal Waveform Memory	12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
Integrated Second Display
Type	Supports touch screen integration of user-supplied second display with split-grid capability. (Note: touch screen driver for second display may not be a Fujitsu driver)
Resolution	Determined by display chosen by user
LeCroy WaveStream Fast Viewing Mode
Intensity	256 Intensity Levels, 1-100% adjustable via front panel control
Types	Select analog or color-graded
Number of Channels	up to 80 simultaneously
Max Sampling Rate	160GS/s
Persistence Aging	Select from 500 ms to Infinity
Waveforms/second (continuous)	up to 2500 Waveforms/second
Operation	Front panel toggle between WaveStream ON (Analog), ON (Color) and OFF
Analog Persistence Display
Analog and Color-Graded Persistence	Variable saturation levels; stores each trace's persistence data in memory
Persistence Types	Select analog, color, or three-dimensional
Trace Selection	Activate persistence on all or any combination of traces
Persistence Aging	Select from 500 ms to infinity
Sweep Display Modes	All accumulated, or all accumulated with last trace highlighted
High Speed Digitizer Output (Option)
Type	Option LSIB-2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
Transfer Rate	up to 325 MB/s (typical) - Maximum of 4 channels (consult Teledyne LeCroy for >4 channels)
Output Protocol	PCI Express, Gen 1 (4 lanes utilized for data transfer)
Control Protocol	TCP/IP
Command Set	Via Windows Automation, or via LeCroy Remote Command Set
Processor/CPU
Processor Memory	32 GB standard. Up to 192 GB optionally available.
Operating System	Microsoft WindowsR 7 Professional Edition (64-bit)
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 12 Zoom and 12 Math/Zoom traces
Setup Storage
Front Panel and Instrument Status	Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
Interface
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Class C (v1.2) Compliant
GPIB Port	Supports IEEE - 488.2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
LSIB Port (optional)	Supports PCIe Gen1 x4 protocol with LeCroy supplied API. Installs in LabMaster LabMaster MCM-Zi-A Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi-A Acquisition Module.
Ethernet Port	Supports 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Ports	LabMaster MCM-Zi -A Master Control Module: minimum 2 total USB 2.0 ports on rear of unit to support Windows compatible devices LabMaster MCM-Zi -A Master Control Module: minimum 3 total USB 2.0 ports on front of unit to support Windows compatible devices
External Monitor Port	Dual Link DVI compatible to support internal display on MCM-Zi Master Control Module (1280 x 768 pixel resolution) and customer-supplied monitor with up to WQXGA (2560 x 1600 pixel) resolution using extended desktop mode.
Auxiliary Input
Signal Types	For External Trigger Input. Located on every LabMaster 10-xxZi-A Acquisition Module (front-mounted BNC, 50 Ω). 10-xxZi-A Acquisition Module that is used for Channels 1-4 contains "active" AUX Input.
Coupling	50 Ω: DC
Max. Input Voltage	5 Vrms
Auxiliary Output
Signal Types	Select from calibrator, control signals or Off
Output Signal	500 Hz-5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0-1 V into 1 MΩ)
Control Signals	Trigger enabled, trigger out, pass/fail status, off
Connector Type	BNC, located on front of every LabMaster 10-xxZi Acquisition Module. 10-xxZi Acquisition Module that is used for Channels 1-4 contains "active" AUX Output.
Automatic Setup
Auto Setup	Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale	Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
General
Auto Calibration	Ensures specified DC and timing accuracy is maintained for 1 year minimum.
Probes
Probes	No passive probes supplied
Probe System	Up to 36 GHz Inputs: 2.92mm interface. Up to 65 GHz Inputs: 1.85mm interface 2.92mm interface automatically detects and supports a variety of compatible probes. Use L2.92A-PLINK or L2.92A-PBUS 2.92mm Probe Adapters to connect 50Ω ProLink or ProBus compatible probes to 2.92mm interface.
Scale Factors	Automatically or manually selected depending on probe used
Calibration Output	MCM-Zi-A Master Control Module: Fast Edge output, 5MHz square wave, 350mVp-p (typical), 50ps rise time, output to SMA connector, AC Coupled
Power Requirements
Voltage	LabMaster 10-xxZi Acquisition Module: 100-240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection, Installation Category II LabMaster MCM-Zi Master Control Module: 100-240 VAC ±10% at 45-66 Hz; Automatic AC Voltage Selection, Installation Category II
Max. Power Consumption	LabMaster 10-xxZi-A Acquisition Module - 1275 W / 1275 VA. LabMaster MCM-Zi-A Master Control Module - 450 W / 450 VA. Each Module and the CPU has a separate power cord.
Environmental and Safety
Temperature (Operating)	+5 ℃ to +40 ℃
Temperature (Non-Operating)	-20 ℃ to +60 ℃
Humidity (Operating)	5% to 80% relative humidity (non-condensing) up to +31 ℃. Upper limit derates to 50% relative humidity (non-condensing) at +40 ℃.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +25 ℃
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Physical Dimensions
Dimensions (HWD)	LabMaster MCM-Zi-A Master Control Module - 10.9"H x 18.2"W x 15.6"D (277 x 462 x 396 mm), LabMaster 10-xxZi-A Acquisition Module - 8.0"H x 18.2"W x 26"D (202 x 462 x 660 mm)
Weight	LabMaster 10-xxZi-A Acquisition Module -58 lbs. (26.4 kg) LabMaster MCM-Zi-A Master Control Module - 47 lbs. (21.4 kg)
Shipping Weight	LabMaster 10-xxZi-A Acquisition Module -76 lbs. (34.5 kg) LabMaster MCM-Zi-A Master Control Module - 56 lbs. (25.5 kg)
Certifications
Certifications	CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, EN61010-2-030, UL 61010-1 3rd edition, and CSA C22.2 No. 61010-1-12
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.

LabMaster 10 Zi-A 65 GHz Systems 　スペック

Vertical System
Analog Bandwidth (Max)	65 GHz
Analog Bandwidth @ 50 Ω (-3 dB) (1.85mm Inputs)	65 GHz (≧10 mV/div)
Analog Bandwidth @ 50 Ω (-3 dB) (2.4/2.92mm Inputs)	36 GHz (≧5 mV/div)
Rise Time (10-90%, 50 Ω)	6.5 ps (test limit, flatness mode)
Rise Time (20-80%, 50 Ω)	4.9 ps (flatness mode)
Input Channels	Up to 40, depending on configuration selected. Up to 80 @ 36 GHz.
Bandwidth Limiters	For ? 36 GHz Mode: 1, 3, 4, 6, 8, 13, 16, 20, 25, 30, 33 GHz. For > 36 GHz Mode: 50, 60 GHz.
Input Impedance	2.92mm Inputs: 50 Ω+/-2% 1.85mm Inputs: 50 Ω+/-2%
Input Coupling	2.92 mm Inputs: 50 Ω: DC, GND 1.85 mm Inputs: 50 Ω: DC
Maximum Input Voltage	2.92 mm Inputs: ±2 [email protected]＜76mV/div, [email protected]≧76mV/div 1.85 mm Inputs: ±2 [email protected]?80mV/div
Channel-Channel Isolation	DC to 36 GHz: 60 dB (>1000:1) (For any two 2.92mm input channels, same or different v/div settings, typical) 36 to 65 GHz: 40 dB (>100:1) (For any two 1.85mm input channels, same or different v/div settings, typical)
Vertical Resolution	8 bits; up to 11 bits with enhanced resolution (ERES)
Sensitivity	50 Ω (2.92mm): 5 mV-500mV/div, fully variable (5-9.9 mV/div via zoom) 50 Ω (1.85mm): 10 mV-80mV/div, fully variable. Higher gain settings possible through use of external attenuators.
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	±1% F.S. (typical), offset at 0V; ±1.5% F.S. (test limit), offset at 0V
Offset Range	50 Ω (1.85 mm): ±500 mV @ 10-80 mV/div 50 Ω (2.92mm): ±500 mV @ 5-75 mV/div ±4 V @ 76 mV/div -500mV/div
Offset Accuracy	50 Ω (2.92mm): 5 mV?500mV/div, fully variable (5-9.9 mV/div via zoom) 50 Ω (1.85mm): 10 mV?80mV/div, fully variable. Higher gain settings possible through use of external attenuators.
DC Vertical Offset Accuracy	±(1.5% of offset setting + 1.5% F.S. + 1 mV) (test limit)
Horizontal System
Timebases	Internal timebase with 10 GHz clock frequency common to all input channels. Single, distributed 10 GHz clock for all channels ensures precise synchronization with timing accuracy between all channels identical to that provided within a single, conventional oscilloscope package.
Time/Division Range	For >36 GHz Mode: 10 ps/div - 320 μs/div (maximum capture time is based on 160 GS/s and installed memory). For ?36 GHz Mode: 10 ps/div-256 s/div (maximum capture time is based on minimum sample rate of 200kS/s and installed memory).
Clock Accuracy	＜0.1 ppm + (aging of 0.05 ppm/yr from last calibration)
Sample Clock Jitter	up to 3.2ms Acquired Time Range: 50fsrms (Internal Timebase Reference) 50fsrms (External Timebase Reference) up to 6.4ms Acquired Time Range: 130fsrms (Internal Timebase Reference) 130fsrms (External Timebase Reference)
Delta Time Measurement Accuracy	√2*√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) (RMS)+(clock accuracy*reading)(seconds)
Jitter Measurement Floor	√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) secondsrms (TIE)
Jitter Between Channels	＜130fsrms (TIE, typical, measured at maximum bandwidth)
Trigger and Interpolator Jitter	＜0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware),
Channel-Channel Deskew Range	±9 x time/div. setting or 25 ns max. (whichever is larger), each channel
External Timebase Reference (Input)	10 MHz or 100MHz; 50 Ω impedance, applied at the rear input of MCM-Zi-A Master Control Module
External Timebase Reference (Output)	10 MHz or 100 MHz ; 50 Ω impedance, output at the rear of MCM-Zi-A Master Control Module
Acquisition System
Single-Shot Sample Rate/Ch	160 GS/s on each channel in >36 GHz Mode. 80 GS/s on each channel in ?36 GHz Mode.
Maximum Trigger Rate	1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
Intersegment Time	1 μs
Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments)	64 M / 64 M / 64 M (In ?36 GHz Modes, reference memory specification for 36 GHz LabMasters) (1000)
Memory Options (4 Ch / 2 Ch / 1Ch) (Number of Segments)	S-32 Option: 64M / 64M / 64M (3,500) M-64 Option: 128M / 128M / 128M (7,500) L-128 Option: 256M / 256M / 256M (15,000) VL-256 Option: 512M / 512M / 512M (15,000) XL-512 Option: 1024M / 1024M / 1024M (15,000) (In ?36 GHz Modes, reference memory specification for LabMaster 10 Zi-A 36 GHz Systems)
Acquisition Processing
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
Enhanced Resolution (ERES)	From 8.5 to 11 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps
Interpolation	Linear or Sin x/x
Triggering System
Modes	Normal, Auto, Single, and Stop
Sources	Any Ch 1-4 (Edge, Window, SMART, Cascade triggers), AUX, internal Fast Edge; or any input channel (Edge trigger only) on additional 10-xxZi-A Acquisition Modules (Channels 5 and higher). Slope and level unique to each source except line trigger.
Coupling Mode	DC, AC, HFRej, LFRej
Pre-trigger Delay	0-100% of memory size (adjustable in 1% increments of 100 ns)
Post-trigger Delay	0-10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
Hold-off by Time or Events	From 2 ns up to 20 s or from 1 to 99,999,999 events
Internal Trigger Range	±4.1 div from center
Trigger Sensitivity with Edge Trigger (1.85/2.4/2.92mm Inputs)	For Ch 1-80 of a LabMaster 10 Zi-A system: 3 div @ ＜ 12 GHz 1.5 div @ ＜ 3 GHz 1.0 div @ ＜ 200 MHz (for DC coupling, ≧ 10 mV/div, 50 Ω)
External Trigger Sensitivity, (Edge Trigger)	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2 div @ ＜ 1 GHz, 1.5 div @ ＜ 500 MHz, 1.0 div @ ＜ 200 MHz, (for DC coupling)
Max. Trigger Frequency, SMART Trigger	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2.0 GHz @ ≧ 10 mV/div (minimum triggerable width 200 ps)
External Trigger Input Range	For any LabMaster 10xx-Zi-A Acquisition Module: Aux (±0.4 V) (Only Ch1-4 Acquisition Module has "active" AUX Input)
Basic Triggers
TV-Composite Video	Not available
High Speed Serial Protocol Triggering
Data Rates	Option LM10Zi-6GBIT-80B-8B10B-TD: 600 Mb/s to 6.5 Gb/s, Channel 4 input only Option LM10Zi-14GBIT-80B-8B10B-TD: 600 Mb/s to 14.1 Gb/s, Channel 4 input only (Note: Channel 3 input will capture signal for triggering when oscilloscope is in ≧25 GHz mode)
Pattern Length	80 bits NRZ, eight 8b/10b symbols
Clock and Data Outputs	No Clock and Data Recovery outputs provided
Measurement Trigger
Measurement Trigger Capability	0
Color Waveform Display
Type	On LabMaster MCM-Zi Master Control Module: Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
Resolution	WXGA; 1280 x 768 pixels.
Number of traces	Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces.
Grid Styles	Auto, Single, Dual, Triple, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Twelve, Sixteen. Up to twenty grids available with some software options.
Waveform Representation	Sample dots joined, or sample dots only
Internal Waveform Memory
Internal Waveform Memory	12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
Integrated Second Display
Type	Supports touch screen integration of user-supplied second display with split-grid capability. (Note: touch screen driver for second display may not be a Fujitsu driver)
Resolution	Determined by display chosen by user
LeCroy WaveStream Fast Viewing Mode
Intensity	256 Intensity Levels, 1-100% adjustable via front panel control
Types	Select analog or color-graded
Number of Channels	up to 80 simultaneously
Max Sampling Rate	160GS/s
Persistence Aging	Select from 500 ms to Infinity
Waveforms/second (continuous)	up to 2500 Waveforms/second
Operation	Front panel toggle between WaveStream ON (Analog), ON (Color) and OFF
Analog Persistence Display
Analog and Color-Graded Persistence	Variable saturation levels; stores each trace's persistence data in memory
Persistence Types	Select analog, color, or three-dimensional
Trace Selection	Activate persistence on all or any combination of traces
Persistence Aging	Select from 500 ms to infinity
Sweep Display Modes	All accumulated, or all accumulated with last trace highlighted
High Speed Digitizer Output (Option)
Type	Option LSIB-2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
Transfer Rate	up to 325 MB/s (typical) - Maximum of 4 channels (consult Teledyne LeCroy for >4 channels)
Output Protocol	PCI Express, Gen 1 (4 lanes utilized for data transfer)
Control Protocol	TCP/IP
Command Set	Via Windows Automation, or via LeCroy Remote Command Set
Processor/CPU
Processor Memory	32 GB standard. Up to 192 GB optionally available.
Operating System	Microsoft WindowsR 7 Professional Edition (64-bit)
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 12 Zoom and 12 Math/Zoom traces
Setup Storage
Front Panel and Instrument Status	Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
Interface
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Class C (v1.2) Compliant
GPIB Port	Supports IEEE - 488.2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
LSIB Port (optional)	Supports PCIe Gen1 x4 protocol with LeCroy supplied API. Installs in LabMaster LabMaster MCM-Zi-A Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi-A Acquisition Module.
Ethernet Port	Supports 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Ports	LabMaster MCM-Zi -A Master Control Module: minimum 2 total USB 2.0 ports on rear of unit to support Windows compatible devices LabMaster MCM-Zi -A Master Control Module: minimum 3 total USB 2.0 ports on front of unit to support Windows compatible devices
External Monitor Port	Dual Link DVI compatible to support internal display on MCM-Zi Master Control Module (1280 x 768 pixel resolution) and customer-supplied monitor with up to WQXGA (2560 x 1600 pixel) resolution using extended desktop mode.
Auxiliary Input
Signal Types	For External Trigger Input. Located on every LabMaster 10-xxZi-A Acquisition Module (front-mounted BNC, 50 Ω). 10-xxZi-A Acquisition Module that is used for Channels 1-4 contains "active" AUX Input.
Coupling	50 Ω: DC
Max. Input Voltage	5 Vrms
Auxiliary Output
Signal Types	Select from calibrator, control signals or Off
Output Signal	500 Hz-5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0-1 V into 1 MΩ)
Control Signals	Trigger enabled, trigger out, pass/fail status, off
Connector Type	BNC, located on front of every LabMaster 10-xxZi Acquisition Module. 10-xxZi Acquisition Module that is used for Channels 1-4 contains "active" AUX Output.
Automatic Setup
Auto Setup	Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale	Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
General
Auto Calibration	Ensures specified DC and timing accuracy is maintained for 1 year minimum.
Probes
Probes	No passive probes supplied
Probe System	Up to 36 GHz Inputs: 2.92mm interface. Up to 65 GHz Inputs: 1.85mm interface 2.92mm interface automatically detects and supports a variety of compatible probes. Use L2.92A-PLINK or L2.92A-PBUS 2.92mm Probe Adapters to connect 50Ω ProLink or ProBus compatible probes to 2.92mm interface.
Scale Factors	Automatically or manually selected depending on probe used
Calibration Output	MCM-Zi-A Master Control Module: Fast Edge output, 5MHz square wave, 350mVp-p (typical), 50ps rise time, output to SMA connector, AC Coupled
Power Requirements
Voltage	LabMaster 10-xxZi Acquisition Module: 100-240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection, Installation Category II LabMaster MCM-Zi Master Control Module: 100-240 VAC ±10% at 45-66 Hz; Automatic AC Voltage Selection, Installation Category II
Max. Power Consumption	LabMaster 10-xxZi-A Acquisition Module - 1275 W / 1275 VA. LabMaster MCM-Zi-A Master Control Module - 450 W / 450 VA. Each Module and the CPU has a separate power cord.
Environmental and Safety
Temperature (Operating)	+5 ℃ to +40 ℃
Temperature (Non-Operating)	-20 ℃ to +60 ℃
Humidity (Operating)	5% to 80% relative humidity (non-condensing) up to +31 ℃. Upper limit derates to 50% relative humidity (non-condensing) at +40 ℃.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +25 ℃
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Physical Dimensions
Dimensions (HWD)	LabMaster MCM-Zi-A Master Control Module - 10.9"H x 18.2"W x 15.6"D (277 x 462 x 396 mm), LabMaster 10-xxZi-A Acquisition Module - 8.0"H x 18.2"W x 26"D (202 x 462 x 660 mm)
Weight	LabMaster 10-xxZi-A Acquisition Module -58 lbs. (26.4 kg) LabMaster MCM-Zi-A Master Control Module - 47 lbs. (21.4 kg)
Shipping Weight	LabMaster 10-xxZi-A Acquisition Module -76 lbs. (34.5 kg) LabMaster MCM-Zi-A Master Control Module - 56 lbs. (25.5 kg)
Certifications
Certifications	CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, EN61010-2-030, UL 61010-1 3rd edition, and CSA C22.2 No. 61010-1-12
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.

LabMaster 10 Zi-A 100 GHz Systems 　スペック

Vertical System
Analog Bandwidth @ 50 Ω (-3 dB) (1mm Inputs)	100 GHz (≧10 mV/div)
Analog Bandwidth (Max)	65 GHz
Analog Bandwidth @ 50 Ω (-3 dB) (2.4/2.92mm Inputs)	36 GHz (≧5 mV/div)
Rise Time (10-90%, 50 Ω)	4.5 ps (flatness mode)
Rise Time (20-80%, 50 Ω)	3.5 ps (flatness mode)
Input Channels	Up to 20, depending on configuration selected. Up to 80 @ 36 GHz.
Bandwidth Limiters	For ? 36 GHz Mode: 1, 3, 4, 6, 8, 13, 16, 20, 25, 30, 33 GHz. For 65 GHz Mode: 50, 60 GHz.
Input Impedance	2.92mm Inputs: 50 Ω+/-2% 1.mm Inputs: 50 Ω+/-2%
Input Coupling	2.92 mm Inputs: 50 Ω: DC, GND 1 mm Inputs: 50 Ω: DC
Maximum Input Voltage	2.92 mm Inputs: ±2 [email protected]＜76mV/div, [email protected]≧76mV/div 1 mm Inputs: ±1 [email protected]?80mV/div
Channel-Channel Isolation	DC to 36 GHz: 60 dB (>1000:1) (For any two 2.92mm input channels, same or different v/div settings, typical) 65 GHz and 100 GHz mode: N/A
Vertical Resolution	8 bits; up to 11 bits with enhanced resolution (ERES)
Sensitivity	50 Ω (2.92mm): 5 mV-500mV/div, fully variable (5-9.9 mV/div via zoom) 50 Ω (1mm): 10 mV-80mV/div, fully variable.
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	±1% F.S. (typical), offset at 0V; ±1.5% F.S. (test limit), offset at 0V
Offset Range	50 Ω (1.mm): ±500 mV @ 10-80 mV/div 50 Ω (2.92mm): ±500 mV @ 5-75 mV/div ±4 V @ 76 mV/div -500mV/div
Offset Accuracy	50 Ω (2.92mm): 5 mV?500mV/div, fully variable (5-9.9 mV/div via zoom) 50 Ω (1mm): 10 mV?80mV/div, fully variable.
DC Vertical Offset Accuracy	±(1.5% of offset setting + 1.5% F.S. + 1 mV) (test limit)
Horizontal System
Timebases	Internal timebase with 10 GHz clock frequency common to all input channels. Single, distributed 10 GHz clock for all channels ensures precise synchronization with timing accuracy between all channels identical to that provided within a single, conventional oscilloscope package.
Time/Division Range	For >36 GHz Mode: 10 ps/div - 320 μs/div (maximum capture time is based on 160 GS/s and installed memory). For ?36 GHz Mode: 10 ps/div-256 s/div (maximum capture time is based on minimum sample rate of 200kS/s and installed memory).
Clock Accuracy	＜0.1 ppm + (aging of 0.05 ppm/yr from last calibration)
Sample Clock Jitter	up to 3.2ms Acquired Time Range: 50fsrms (Internal Timebase Reference) 50fsrms (External Timebase Reference) up to 6.4ms Acquired Time Range: 130fsrms (Internal Timebase Reference) 130fsrms (External Timebase Reference)
Delta Time Measurement Accuracy	√2*√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) (RMS)+(clock accuracy*reading)(seconds)
Jitter Measurement Floor	√((Noise/SlewRate)^2+(Sample Clock Jitter)^2 ) secondsrms (TIE)
Jitter Between Channels	＜130fsrms (TIE, typical, measured at maximum bandwidth)
Trigger and Interpolator Jitter	＜0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware),
Channel-Channel Deskew Range	±9 x time/div. setting or 25 ns max. (whichever is larger), each channel
External Timebase Reference (Input)	10 MHz or 100MHz; 50 Ω impedance, applied at the rear input of MCM-Zi-A Master Control Module
External Timebase Reference (Output)	10 MHz or 100 MHz ; 50 Ω impedance, output at the rear of MCM-Zi-A Master Control Module
Acquisition System
Single-Shot Sample Rate/Ch	240 GS/s on each channel in 100 GHz Mode. 160 GS/s on each channel in 65 GHz Mode. 80 GS/s on each channel in ?36 GHz Mode.
Maximum Trigger Rate	1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
Intersegment Time	1 μs
Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments)	96 M / 96 M / 96 M (In ?36 GHz Modes, reference memory specification for 36 GHz LabMasters) (1000)
Memory Options (4 Ch / 2 Ch / 1Ch) (Number of Segments)	S-32 Option: 96M / 96M / 96M (3,500) M-64 Option: 192M / 192M / 192M (7,500) L-128 Option: 384M / 384M / 385M (15,000) VL-256 Option: 768M / 768M / 768M (15,000) XL-512 Option: 1536M / 1536M / 1536M (15,000) (In ?36 GHz Modes, reference memory specification for LabMaster 10 Zi-A 36 GHz Systems)
Acquisition Processing
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
Enhanced Resolution (ERES)	From 8.5 to 11 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps
Interpolation	Linear or Sin x/x
Triggering System
Modes	Normal, Auto, Single, and Stop
Sources	Any Ch 1-4 (Edge, Window, SMART, Cascade triggers), AUX, internal Fast Edge; or any input channel (Edge trigger only) on additional 10-xxZi-A Acquisition Modules (Channels 5 and higher). Slope and level unique to each source except line trigger.
Coupling Mode	DC, AC, HFRej, LFRej
Pre-trigger Delay	0-100% of memory size (adjustable in 1% increments of 100 ns)
Post-trigger Delay	0-10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
Hold-off by Time or Events	From 2 ns up to 20 s or from 1 to 99,999,999 events
Internal Trigger Range	±4.1 div from center
Trigger Sensitivity with Edge Trigger (1.85/2.4/2.92mm Inputs)	For Ch 1-80 of a LabMaster 10 Zi-A system: 3 div @ ＜ 12 GHz 1.5 div @ ＜ 3 GHz 1.0 div @ ＜ 200 MHz (for DC coupling, ≧ 10 mV/div, 50 Ω)
External Trigger Sensitivity, (Edge Trigger)	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2 div @ ＜ 1 GHz, 1.5 div @ ＜ 500 MHz, 1.0 div @ ＜ 200 MHz, (for DC coupling)
Max. Trigger Frequency, SMART Trigger	For Ch 1-4 only of any LabMaster 10xx-Zi-A Acquisition Module: 2.0 GHz @ ≧ 10 mV/div (minimum triggerable width 200 ps)
External Trigger Input Range	For any LabMaster 10xx-Zi-A Acquisition Module: Aux (±0.4 V) (Only Ch1-4 Acquisition Module has "active" AUX Input)
High Speed Serial Protocol Triggering
Clock and Data Outputs	No Clock and Data Recovery outputs provided
Measurement Trigger
Measurement Trigger Capability	0
Color Waveform Display
Type	On LabMaster MCM-Zi Master Control Module: Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
Resolution	WXGA; 1280 x 768 pixels.
Number of traces	Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces.
Grid Styles	Auto, Single, Dual, Triple, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Twelve, Sixteen. Up to twenty grids available with some software options.
Waveform Representation	Sample dots joined, or sample dots only
Internal Waveform Memory
Internal Waveform Memory	12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
Integrated Second Display
Type	Supports touch screen integration of user-supplied second display with split-grid capability. (Note: touch screen driver for second display may not be a Fujitsu driver)
Resolution	Determined by display chosen by user
LeCroy WaveStream Fast Viewing Mode
Intensity	256 Intensity Levels, 1-100% adjustable via front panel control
Types	Select analog or color-graded
Number of Channels	up to 80 simultaneously
Max Sampling Rate	240 GS/s
Persistence Aging	Select from 500 ms to Infinity
Waveforms/second (continuous)	up to 2500 Waveforms/second
Operation	Front panel toggle between WaveStream ON (Analog), ON (Color) and OFF
Analog Persistence Display
Analog and Color-Graded Persistence	Variable saturation levels; stores each trace's persistence data in memory
Persistence Types	Select analog, color, or three-dimensional
Trace Selection	Activate persistence on all or any combination of traces
Persistence Aging	Select from 500 ms to infinity
Sweep Display Modes	All accumulated, or all accumulated with last trace highlighted
High Speed Digitizer Output (Option)
Type	Option LSIB-2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
Transfer Rate	up to 325 MB/s (typical) - Maximum of 4 channels (consult Teledyne LeCroy for >4 channels)
Output Protocol	PCI Express, Gen 1 (4 lanes utilized for data transfer)
Control Protocol	TCP/IP
Command Set	Via Windows Automation, or via LeCroy Remote Command Set
Processor/CPU
Processor Memory	32 GB standard. Up to 192 GB optionally available.
Operating System	Microsoft WindowsR 7 Professional Edition (64-bit)
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 12 Zoom and 12 Math/Zoom traces
Setup Storage
Front Panel and Instrument Status	Store to the internal hard drive, over the network, or to a USB-connected peripheral device.
Interface
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Class C (v1.2) Compliant
GPIB Port	Supports IEEE - 488.2. Installs in LabMaster MCM-Zi Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi Acquisition Module.
LSIB Port (optional)	Supports PCIe Gen1 x4 protocol with LeCroy supplied API. Installs in LabMaster LabMaster MCM-Zi-A Master Control Module and uses one available PCIe slot normally used by a LabMaster 10-xxZi-A Acquisition Module.
Ethernet Port	Supports 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Ports	LabMaster MCM-Zi -A Master Control Module: minimum 2 total USB 2.0 ports on rear of unit to support Windows compatible devices LabMaster MCM-Zi -A Master Control Module: minimum 3 total USB 2.0 ports on front of unit to support Windows compatible devices
External Monitor Port	Dual Link DVI compatible to support internal display on MCM-Zi Master Control Module (1280 x 768 pixel resolution) and customer-supplied monitor with up to WQXGA (2560 x 1600 pixel) resolution using extended desktop mode.
Auxiliary Input
Signal Types	For External Trigger Input. Located on every LabMaster 10-xxZi-A Acquisition Module (front-mounted BNC, 50 Ω). 10-xxZi-A Acquisition Module that is used for Channels 1-4 contains "active" AUX Input.
Coupling	50 Ω: DC
Max. Input Voltage	5 Vrms
Auxiliary Output
Signal Types	Select from calibrator, control signals or Off
Output Signal	500 Hz-5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0-1 V into 1 MΩ)
Control Signals	Trigger enabled, trigger out, pass/fail status, off
Connector Type	BNC, located on front of every LabMaster 10-xxZi Acquisition Module. 10-xxZi Acquisition Module that is used for Channels 1-4 contains "active" AUX Output.
Automatic Setup
Auto Setup	Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
Find Vertical Scale	Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
General
Auto Calibration	Ensures specified DC and timing accuracy is maintained for 1 year minimum.
Probes
Probes	No passive probes supplied
Probe System	Up to 36 GHz Inputs: 2.92mm interface. Up to 100 GHz Inputs: 1.mm interface 2.92mm interface automatically detects and supports a variety of compatible probes. Use L2.92A-PLINK or L2.92A-PBUS 2.92mm Probe Adapters to connect 50Ω ProLink or ProBus compatible probes to 2.92mm interface.
Scale Factors	Automatically or manually selected depending on probe used
Calibration Output	MCM-Zi-A Master Control Module: Fast Edge output, 5MHz square wave, 350mVp-p (typical), 50ps rise time, output to SMA connector, AC Coupled
Power Requirements
Voltage	LabMaster 10-xxZi Acquisition Module: 100-240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection, Installation Category II LabMaster MCM-Zi Master Control Module: 100-240 VAC ±10% at 45-66 Hz; Automatic AC Voltage Selection, Installation Category II
Max. Power Consumption	LabMaster 10-xxZi-A Acquisition Module - 1275 W / 1275 VA. LabMaster MCM-Zi-A Master Control Module - 450 W / 450 VA. Each Module and the CPU has a separate power cord.
Environmental and Safety
Temperature (Operating)	+5 ℃ to +40 ℃
Temperature (Non-Operating)	-20 ℃ to +60 ℃
Humidity (Operating)	5% to 80% relative humidity (non-condensing) up to +31 ℃. Upper limit derates to 50% relative humidity (non-condensing) at +40 ℃.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +25 ℃
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Physical Dimensions
Dimensions (HWD)	LabMaster MCM-Zi-A Master Control Module - 10.9"H x 18.2"W x 15.6"D (277 x 462 x 396 mm), LabMaster 10-xxZi-A Acquisition Module - 8.0"H x 18.2"W x 26"D (202 x 462 x 660 mm)
Weight	LabMaster 10-xxZi-A Acquisition Module -58 lbs. (26.4 kg) LabMaster MCM-Zi-A Master Control Module - 47 lbs. (21.4 kg)
Shipping Weight	LabMaster 10-xxZi-A Acquisition Module -76 lbs. (34.5 kg) LabMaster MCM-Zi-A Master Control Module - 56 lbs. (25.5 kg)
Certifications
Certifications	CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, EN61010-2-030, UL 61010-1 3rd edition, and CSA C22.2 No. 61010-1-12
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.