![]() 高精度12ビット・オシロスコープ
|
![]() |
(日本語字幕付きデモビデオ)
|
モデル名 | 帯域 | ch数 | サンプリ ング速度 |
標準メモリ | 垂直分解能 |
---|---|---|---|---|---|
WavePro 254HD | 2.5GHz | 4ch | 10GS/s ~20GS/s |
50Mポイント/ch (100Mポイント @2ch) |
12ビット (分解能向上演算 (ERES)使用時 に最大15ビット) |
WavePro 404HD | 4GHz | ||||
WavePro 604HD | 6GHz | ||||
WavePro 804HD | 8GHz | ||||
ミックスド・シグナル・オシロスコープ | |||||
WavePro 254HD-MS | 2.5GHz | 4ch + デジタル 16ch |
10GS/s ~20GS/s |
50Mポイント/ch (100Mポイント @2ch) |
12ビット (分解能向上演算 (ERES)使用時に 最大15ビット) |
WavePro 404HD-MS | 4GHz | ||||
WavePro 604HD-MS | 6GHz | ||||
WavePro 804HD-MS | 8GHz |
モデルごとスペック詳細(モデル名をクリックで詳細表示されます)

Vertical - Analog Channels | |
Analog Bandwidth (Max) | 2.5 GHz |
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input) | 1 GHz (typical) |
Rise Time (10-90%, 50 Ω) | 166 ps |
Rise Time (20-80%, 50 Ω) | 117 ps |
Input Channels | 4 |
Vertical Resolution | 12 bits; up to 15 bits with enhanced resolution (ERES) |
Effective Number of Bits (ENOB) | 7.8 bits |
Vertical Noise Floor (1 mV/div) | 155 µV |
Vertical Noise Floor (2 mV/div) | 155 µV |
Vertical Noise Floor (5 mV/div) | 155 µV |
Vertical Noise Floor (10 mV/div) | 155 µV |
Vertical Noise Floor (20 mV/div) | 191 µV |
Vertical Noise Floor (50 mV/div) | 429 µV |
Vertical Noise Floor (100 mV/div) | 889 µV |
Vertical Noise Floor (200 mV/div) | 1.44 mV |
Vertical Noise Floor (500 mV/div) | 3.66 mV |
Vertical Noise Floor (1 V/div) | 6.70 mV |
Sensitivity | 50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable |
DC Vertical Gain Accuracy (Gain Component of DC Accuracy) | ±(0.5%) F.S, offset at 0 V |
Channel-Channel Isolation | 70dB up to 200 MHz 60dB up to 500 MHz 50dB up to 1 GHz 40dB up to 2.5 GHz |
Offset Range | 50 Ω, ≤1 GHz BWL 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-1V: +/-10V 50 Ω, >1 GHz BWL 1mV/div-34.5mV/div: +/- 0.5V 35mV/div-87mV/div: +/- 1.25V 88mV/div-220mV/div: +/-3V 225mV/div-1V/div: +/-5V 1 MΩ 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-100mV: +/-16V 102mV-198mV: +/-80V 200mV-1V: +/-160V 1.02V-10V: +/-400V |
DC Vertical Offset Accuracy | +/-(0.5% of offset value + 0.5%FS + 1mV) |
Maximum Input Voltage | 50 Ω, ≤1 GHz BWL 5V RMS, +/- 10V Peak 50 Ω, >1 GHz BWL '+/-2V max. up to 34.5mV/div +/-5V max. 35mV/div to 87mV/div 5.5Vrms >87mV/div 1 MΩ 400 V max (Peak DC+AC) |
Input Coupling | 1 MΩ: AC, DC, GND; 50 Ω: DC, GND |
Input Impedance | 50 Ω+/-2% or 1 MΩ||14pF, 10 MΩ || 9.5 pF |
Bandwidth Limiters | 20MHz, 200MHz, 500 MHz, 1 GHz |
Rescaling | Length: meters, inches, feet, yards, miles; Mass: grams, slugs; Temperature: celsius, fahrenheit, kelvin; Angle: radian, arcdegr, arcmin, arcsec, cycles, revolutions, turns; Velocity: m/s, in/s, ft/s, yd/s, miles/s; Acceleration: m/s2, in/s2, ft/s2, g0; Volume: liters, cubic meters, cubic inches, cubic feet, cubic yards; Force (Weight): newton, grain, ounce, pound; Pressure: pascal, bar, atmosphere (technical), atmosphere (standard), torr, psi; Electrical: volts, amps, watts, volt-amperes, volt-amperes reactive, farad, coulomb, ohm, siemen, volt/meter, coulomb/m2, farad/meter, siemen/meter, power factor; Magnetic: weber, tesla, henry, amp/meter, henry/meter; Energy: joule, Btu, calorie; Rotating Machine: radian/second, frequency, revolution/second, revolution/minute, N?m, lb-ft, lb-in, oz-in, watt, horsepower; Other: %. |
Horizontal - Analog Channels | |
Timebases | Internal timebase common to 4 input channels |
Acquisition Modes | Real-time |
Time/Division Range | 20ps/div - 1 ks/div |
Clock Accuracy | +/-100ppb for 5 to 40C + 0.10ppm/year from calibration |
Sample Clock Jitter | up to 10µs Acquired Time Range: 60 fsrms (Internal Timebase Reference) up to 10ms Acquired Time Range: 100 fsrms (Internal Timebase Reference) |
Delta Time Measurement Accuracy | \sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds) |
Jitter Measurement Floor | \sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)} |
Channel-Channel Deskew Range | ±9 x time/div. setting, 100 ms max., each channel |
External Timebase Reference (Input) | 10MHz +/-25ppm at 0 to 10dBm into 50Ohms |
External Timebase Reference (Output) | 10MHz, 5.0 dBm +/-2.5 dBm, sinewave synchronized to reference being used (internal or external reference) |
External Clock | N/A |
Acquisition - Analog Channels | |
Sample Rate (Single-shot) | 10 GS/s on 4 Ch 20 GS/s on 2 Ch |
Sample Rate (Repetitive) | N/A |
Memory Length (4 Ch / 2 Ch / 1Ch) (Number of Segments) | 50M/100M |
Memory Length Options (4 Ch / 2 Ch / 1Ch) (Number of Segments) | WPHD-200MPT Option: 100M / 200M WPHD-500MPT Option: 250M / 500M WPHD-1000MPT Option: 500M / 1000M WPHD-2000MPT Option: 1000M / 2000M WPHD-5000MPT Option: 2500M / 5000M |
Averaging | Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps (Waveforms of ≤500Mpts) |
Envelope (Extrema) | Envelope, floor, or roof for up to 1 million sweeps (Waveforms of ≤500Mpts) |
Interpolation | Linear or Sin x/x (2 pt and 5 pt) (Waveforms of ≤500Mpts) |
Triggering System | |
Modes | Acquisition of ≤500Mpts: Normal, Auto, Single, and Stop Acquisition of >500Mpts: Single |
Sources | Any input channel, Ext, Ext/10, Line, or Fast Edge; slope and level unique to each source (except Line and Fast edge) |
Coupling | DC, AC, HFRej, LFRej |
Pre-trigger Delay | 0-100% of memory size |
Post-trigger Delay | No limitation |
Hold-off | From 1 ns up to 20 s or from 1 to 99,999,999 events |
Trigger and Interpolator Jitter | ≤ 2.5 ps RMS (typical) <0.1 ps RMS (typical, software assisted) |
Internal Trigger Level Range | ±4.1 div from center (typical) |
External Trigger Level Range | Ext (±0.4 V); Ext/10 (±4 V) |
Maximum Trigger Rate | 650,000 waveforms/second (in Sequence Mode, up to 4 channels) |
Trigger Sensitivity with Edge Trigger ProBus Inputs | 0.75 div |
Trigger Sensitivity with Edge Trigger (Aux Input) | 0.5 div @ < 1 GHz |
Max. Trigger Frequency, SMART Trigger | 2.0 GHz @ ≥ 10 mV/div (minimum triggerable width 200 ps) |
Trigger Types | |
Edge | Triggers when signal meets slope (positive, negative, or either) and level condition. |
Width | Triggers on positive or negative glitches with selectable widths. Minimum width 500 ps, maximum width: 20 s |
Glitch | Triggers on positive or negative glitches with selectable widths. Minimum width 200 ps, maximum width: 20 s |
Window | Triggers when signal exits a window defined by adjustable thresholds |
Pattern | Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern. |
TV-Composite Video | Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative). |
Runt | Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns. |
Slew Rate | Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
Interval | Triggers on intervals selectable between 1 ns and 20 s. |
Dropout | Triggers if signal drops out for longer than selected time between 1 ns and 20 s. |
Measurement Trigger | Select from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger. |
Multi-Stage: Qualified (Timeout or State/Edge Qualified) | Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
Triggers with Exclusion Technology | Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met |
Multi-Stage: Qualified First | In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
TriggerScan | A Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially. |
Low Speed Serial Protocol Trigger (Optional) | |
Supported Protocols | I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, MIL-STD-1553, USB 1.x/2.0 |
Measurement Tools | |
Measurement Functionality | Display up to 12 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state. |
Measurement Parameters - Horizontal + Jitter | Cycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min |
Measurement Parameters - Vertical | Amplitude, Base, [email protected], Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top. |
Measurement Parameters - Pulse | Area, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%) |
Measurement Parameters - Statistical (on Histograms) | Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total) |
Math Tools | |
Math Functionality | Display up to 12 math functions traces (F1-F12). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math. |
Math Operators - Basic Math | Average (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+). |
Math Operators - Digital (incl. with MSO models/options) | Digital AND, Digital DFlipFlop, Digital NAND, Digital NOR, Digital NOT, Digital OR, Digital XOR |
Math Operators - Filters | Enhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x. |
Math Operators - Frequency Analysis | FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows. |
Math Operators - Functions | Absolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity). |
Math Operators - Other | Segment, Sparse |
Measurement and Math Integration | |
Measurement and Math Integration | Histograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma) |
Pass/Fail Testing | |
Pass/Fail Testing | Display up to 12 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value <. ≤, =, >, ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook. |
Display System | |
Size | Color 15.6" widescreen capacitive touch screen |
Resolution | 1920 x 1080 pixels |
Number of traces | Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces. |
Grid Styles | Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Quatro, Twelve, Sixteen |
Waveform Representation | Sample dots joined, or sample dots only |
Persistence Display | |
Analog and Color-Graded Persistence | Waveforms of ≤500Mpts: Variable saturation levels; stores each trace’s persistence data in memory |
Persistence Types | Waveforms of ≤500Mpts: Select analog, color, or three-dimensional |
Trace Selection | Waveforms of ≤500Mpts: Activate persistence on all or any combination of traces |
Persistence Aging | Waveforms of ≤500Mpts: Select from 500 ms to infinity |
Sweep Display Modes | Waveforms of ≤500Mpts: All accumulated, or all accumulated with last trace highlighted |
Zoom Expansion Traces | |
Zoom Expansion Traces | Display up to 12 Zoom and 12 Math/Zoom traces |
Internal Waveform Memory | |
Internal Waveform Memory | 12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity. |
Setup Storage | |
Front Panel and Instrument Status | Store to the internal hard drive, over the network, or to a USB-connected peripheral device. |
Automatic Setup | |
Auto Setup | Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals |
Find Vertical Scale | Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range |
Calibration | |
Auto Calibration | Ensures specified DC and timing accuracy is maintained for 1 year minimum. |
Processor/CPU | |
Type | Intel® Core i5-6500 Quad Core, 3.2 GHz (or better) |
Processor Memory | 16 GB standard |
Operating System | Microsoft Windows® 10 |
Oscilloscope Operating Software | Teledyne LeCroy MAUI™ with OneTouch |
Real Time Clock | Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks. |
Connectivity | |
Ethernet Port | 2 x 10/100/1000BaseT Ethernet interface (RJ45 port) |
USB Host Ports | 4 side USB 3.1 Gen1 ports, 3 front USB 3.1 Gen1 ports |
USB Device Port | 1 port - USBTMC over USB 3.1 Gen1 |
GPIB Port (optional) | Supports IEEE - 488.2 (External) |
External Monitor Port | 1 x DisplayPort, supports up to 4096x2304 @ 24 Hz 1 x HDMI, supports up to 4096x2304 @ 60 Hz |
Remote Control | Via Windows Automation, or via LeCroy Remote Command Set |
Network Communication Standard | VXI-11 or VICP, LXI Compatible |
Auxiliary Input | |
Signal Types | For external trigger input |
Coupling | 50 Ω: DC; 1 MΩ: AC, DC, GND |
Max. Input Voltage | 50 Ω 5V RMS, +/- 10V Peak 1 MΩ 400 V max (Peak DC+AC) |
Auxiliary Output | |
Signal Types | Select from outpout signal, control signals, off |
Output Signal | 500 Hz-5 MHz square wave or DC level; 50 mV-1 V into 1 MΩ |
Control Signals | Trigger enabled, trigger out, pass/fail status, fast edge, off |
Connector Type | BNC, located on front |
Probes | |
Probes | Qty. (4) ÷10 Passive Probes |
Probe System | ProBus2. Automatically detects and supports a variety of compatible probes. Fully backwards-compatible to ProBus probes without the use of adapters. |
Scale Factors | Automatically or manually selected depending on probe used |
Calibration Output | Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 500 Hz to 1 MHz square wave; 50 mV to 1.0V. |
Power Requirements | |
Voltage | 90 - 132 Vrms, 380 - 420Hz 90 - 264 Vrms, 47 - 63 Hz |
Nominal Power Consumption | 400W/400VA |
Max. Power Consumption | 525W/525VA |
Certifications | |
Certifications | CE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No. 61010-1-12 |
Environmental | |
Temperature (Operating) | +5 °C to +40 °C |
Temperature (Non-Operating) | -20 °C to +60 °C |
Humidity (Operating) | 5% to 90% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C. |
Humidity (Non-Operating) | 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F |
Altitude (Operating) | Up to 10,000 ft. (3048 m) at or below +30 °C |
Altitude (Non-Operating) | Up to 40,000 ft. (12,192 m) |
Random Vibration (Operating) | 0.31 grms 5 Hz to 500 Hz, 20 minutes in each of three orthogonal axes |
Random Vibration (Non-Operating) | 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes |
Functional Shock | 30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total |
Size and Weight | |
Dimensions (HWD) | 13.6” H x 17.5” W x 7.7” D (345 x 445 x 196 mm) |
Weight | 24.4 lbs (11.1 kg) |
Shipping Weight | 34 lbs |
Warranty and Service | |
Warranty and Service | 3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services. |

Vertical - Analog Channels | |
Analog Bandwidth (Max) | 4 GHz |
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input) | 1 GHz (typical) |
Rise Time (10-90%, 50 Ω) | 104 ps |
Rise Time (20-80%, 50 Ω) | 73 ps |
Input Channels | 4 |
Vertical Resolution | 12 bits; up to 15 bits with enhanced resolution (ERES) |
Effective Number of Bits (ENOB) | 7.5 bits |
Vertical Noise Floor (1 mV/div) | 228 µV |
Vertical Noise Floor (2 mV/div) | 228 µV |
Vertical Noise Floor (5 mV/div) | 228 µV |
Vertical Noise Floor (10 mV/div) | 228 µV |
Vertical Noise Floor (20 mV/div) | 275 µV |
Vertical Noise Floor (50 mV/div) | 633 µV |
Vertical Noise Floor (100 mV/div) | 1.31 mV |
Vertical Noise Floor (200 mV/div) | 2.06 mV |
Vertical Noise Floor (500 mV/div) | 5.16 mV |
Vertical Noise Floor (1 V/div) | 9.17 mV |
Sensitivity | 50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable |
DC Vertical Gain Accuracy (Gain Component of DC Accuracy) | ±(0.5%) F.S, offset at 0 V |
Channel-Channel Isolation | 70dB up to 200 MHz 60dB up to 500 MHz 50dB up to 1 GHz 40dB up to 2.5 GHz 30dB up to 4 GHz |
Offset Range | 50 Ω, ≤1 GHz BWL 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-1V: +/-10V 50 Ω, >1 GHz BWL 1mV/div-34.5mV/div: +/- 0.5V 35mV/div-87mV/div: +/- 1.25V 88mV/div-220mV/div: +/-3V 225mV/div-1V/div: +/-5V 1 MΩ 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-100mV: +/-16V 102mV-198mV: +/-80V 200mV-1V: +/-160V 1.02V-10V: +/-400V |
DC Vertical Offset Accuracy | +/-(0.5% of offset value + 0.5%FS + 1mV) |
Maximum Input Voltage | 50 Ω, ≤1 GHz BWL 5V RMS, +/- 10V Peak 50 Ω, >1 GHz BWL '+/-2V max. up to 34.5mV/div +/-5V max. 35mV/div to 87mV/div 5.5Vrms >87mV/div 1 MΩ 400 V max (Peak DC+AC) |
Input Coupling | 1 MΩ: AC, DC, GND; 50 Ω: DC, GND |
Input Impedance | 50 Ω+/-2% or 1 MΩ||14pF, 10 MΩ || 9.5 pF |
Bandwidth Limiters | 20MHz, 200MHz, 500 MHz, 1 GHz, 2.5 GHz |
Rescaling | Length: meters, inches, feet, yards, miles; Mass: grams, slugs; Temperature: celsius, fahrenheit, kelvin; Angle: radian, arcdegr, arcmin, arcsec, cycles, revolutions, turns; Velocity: m/s, in/s, ft/s, yd/s, miles/s; Acceleration: m/s2, in/s2, ft/s2, g0; Volume: liters, cubic meters, cubic inches, cubic feet, cubic yards; Force (Weight): newton, grain, ounce, pound; Pressure: pascal, bar, atmosphere (technical), atmosphere (standard), torr, psi; Electrical: volts, amps, watts, volt-amperes, volt-amperes reactive, farad, coulomb, ohm, siemen, volt/meter, coulomb/m2, farad/meter, siemen/meter, power factor; Magnetic: weber, tesla, henry, amp/meter, henry/meter; Energy: joule, Btu, calorie; Rotating Machine: radian/second, frequency, revolution/second, revolution/minute, N?m, lb-ft, lb-in, oz-in, watt, horsepower; Other: %. |
Horizontal - Analog Channels | |
Timebases | Internal timebase common to 4 input channels |
Acquisition Modes | Real-time |
Time/Division Range | 20ps/div - 1 ks/div |
Clock Accuracy | +/-100ppb for 5 to 40C + 0.10ppm/year from calibration |
Sample Clock Jitter | up to 10µs Acquired Time Range: 60 fsrms (Internal Timebase Reference) up to 10ms Acquired Time Range: 100 fsrms (Internal Timebase Reference) |
Delta Time Measurement Accuracy | \sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds) |
Jitter Measurement Floor | \sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)} |
Channel-Channel Deskew Range | ±9 x time/div. setting, 100 ms max., each channel |
External Timebase Reference (Input) | 10MHz +/-25ppm at 0 to 10dBm into 50Ohms |
External Timebase Reference (Output) | 10MHz, 5.0 dBm +/-2.5 dBm, sinewave synchronized to reference being used (internal or external reference) |
External Clock | N/A |
Acquisition - Analog Channels | |
Sample Rate (Single-shot) | 10 GS/s on 4 Ch 20 GS/s on 2 Ch |
Sample Rate (Repetitive) | N/A |
Memory Length (4 Ch / 2 Ch / 1Ch) (Number of Segments) | 50M/100M |
Memory Length Options (4 Ch / 2 Ch / 1Ch) (Number of Segments) | WPHD-200MPT Option: 100M / 200M WPHD-500MPT Option: 250M / 500M WPHD-1000MPT Option: 500M / 1000M WPHD-2000MPT Option: 1000M / 2000M WPHD-5000MPT Option: 2500M / 5000M |
Averaging | Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps (Waveforms of ≤500Mpts) |
Envelope (Extrema) | Envelope, floor, or roof for up to 1 million sweeps (Waveforms of ≤500Mpts) |
Interpolation | Linear or Sin x/x (2 pt and 5 pt) (Waveforms of ≤500Mpts) |
Triggering System | |
Modes | Acquisition of ≤500Mpts: Normal, Auto, Single, and Stop Acquisition of >500Mpts: Single |
Sources | Any input channel, Ext, Ext/10, Line, or Fast Edge; slope and level unique to each source (except Line and Fast edge) |
Coupling | DC, AC, HFRej, LFRej |
Pre-trigger Delay | 0-100% of memory size |
Post-trigger Delay | No limitation |
Hold-off | From 1 ns up to 20 s or from 1 to 99,999,999 events |
Trigger and Interpolator Jitter | ≤ 2.5 ps RMS (typical) <0.1 ps RMS (typical, software assisted) |
Internal Trigger Level Range | ±4.1 div from center (typical) |
External Trigger Level Range | Ext (±0.4 V); Ext/10 (±4 V) |
Maximum Trigger Rate | 650,000 waveforms/second (in Sequence Mode, up to 4 channels) |
Trigger Sensitivity with Edge Trigger ProBus Inputs | 0.75 div |
Trigger Sensitivity with Edge Trigger (Aux Input) | 0.5 div @ < 1 GHz |
Max. Trigger Frequency, SMART Trigger | 2.0 GHz @ ≥ 10 mV/div (minimum triggerable width 200 ps) |
Trigger Types | |
Edge | Triggers when signal meets slope (positive, negative, or either) and level condition. |
Width | Triggers on positive or negative glitches with selectable widths. Minimum width 500 ps, maximum width: 20 s |
Glitch | Triggers on positive or negative glitches with selectable widths. Minimum width 200 ps, maximum width: 20 s |
Window | Triggers when signal exits a window defined by adjustable thresholds |
Pattern | Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern. |
TV-Composite Video | Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative). |
Runt | Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns. |
Slew Rate | Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
Interval | Triggers on intervals selectable between 1 ns and 20 s. |
Dropout | Triggers if signal drops out for longer than selected time between 1 ns and 20 s. |
Measurement Trigger | Select from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger. |
Multi-Stage: Qualified (Timeout or State/Edge Qualified) | Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
Triggers with Exclusion Technology | Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met |
Multi-Stage: Qualified First | In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
TriggerScan | A Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially. |
Low Speed Serial Protocol Trigger (Optional) | |
Supported Protocols | I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, MIL-STD-1553, USB 1.x/2.0 |
Measurement Tools | |
Measurement Functionality | Display up to 12 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state. |
Measurement Parameters - Horizontal + Jitter | Cycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min |
Measurement Parameters - Vertical | Amplitude, Base, [email protected], Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top. |
Measurement Parameters - Pulse | Area, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%) |
Measurement Parameters - Statistical (on Histograms) | Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total) |
Math Tools | |
Math Functionality | Display up to 12 math functions traces (F1-F12). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math. |
Math Operators - Basic Math | Average (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+). |
Math Operators - Digital (incl. with MSO models/options) | Digital AND, Digital DFlipFlop, Digital NAND, Digital NOR, Digital NOT, Digital OR, Digital XOR |
Math Operators - Filters | Enhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x. |
Math Operators - Frequency Analysis | FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows. |
Math Operators - Functions | Absolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity). |
Math Operators - Other | Segment, Sparse |
Measurement and Math Integration | |
Measurement and Math Integration | Histograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma) |
Pass/Fail Testing | |
Pass/Fail Testing | Display up to 12 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value <. ≤, =, >, ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook. |
Display System | |
Size | Color 15.6" widescreen capacitive touch screen |
Resolution | 1920 x 1080 pixels |
Number of traces | Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces. |
Grid Styles | Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Quatro, Twelve, Sixteen |
Waveform Representation | Sample dots joined, or sample dots only |
Persistence Display | |
Analog and Color-Graded Persistence | Waveforms of ≤500Mpts: Variable saturation levels; stores each trace’s persistence data in memory |
Persistence Types | Waveforms of ≤500Mpts: Select analog, color, or three-dimensional |
Trace Selection | Waveforms of ≤500Mpts: Activate persistence on all or any combination of traces |
Persistence Aging | Waveforms of ≤500Mpts: Select from 500 ms to infinity |
Sweep Display Modes | Waveforms of ≤500Mpts: All accumulated, or all accumulated with last trace highlighted |
Zoom Expansion Traces | |
Zoom Expansion Traces | Display up to 12 Zoom and 12 Math/Zoom traces |
Internal Waveform Memory | |
Internal Waveform Memory | 12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity. |
Setup Storage | |
Front Panel and Instrument Status | Store to the internal hard drive, over the network, or to a USB-connected peripheral device. |
Automatic Setup | |
Auto Setup | Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals |
Find Vertical Scale | Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range |
Calibration | |
Auto Calibration | Ensures specified DC and timing accuracy is maintained for 1 year minimum. |
Processor/CPU | |
Type | Intel® Core i5-6500 Quad Core, 3.2 GHz (or better) |
Processor Memory | 16 GB standard |
Operating System | Microsoft Windows® 10 |
Oscilloscope Operating Software | Teledyne LeCroy MAUI™ with OneTouch |
Real Time Clock | Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks. |
Connectivity | |
Ethernet Port | 2 x 10/100/1000BaseT Ethernet interface (RJ45 port) |
USB Host Ports | 4 side USB 3.1 Gen1 ports, 3 front USB 3.1 Gen1 ports |
USB Device Port | 1 port - USBTMC over USB 3.1 Gen1 |
GPIB Port (optional) | Supports IEEE - 488.2 (External) |
External Monitor Port | 1 x DisplayPort, supports up to 4096x2304 @ 24 Hz 1 x HDMI, supports up to 4096x2304 @ 60 Hz |
Remote Control | Via Windows Automation, or via LeCroy Remote Command Set |
Network Communication Standard | VXI-11 or VICP, LXI Compatible |
Auxiliary Input | |
Signal Types | For external trigger input |
Coupling | 50 Ω: DC; 1 MΩ: AC, DC, GND |
Max. Input Voltage | 50 Ω 5V RMS, +/- 10V Peak 1 MΩ 400 V max (Peak DC+AC) |
Auxiliary Output | |
Signal Types | Select from outpout signal, control signals, off |
Output Signal | 500 Hz-5 MHz square wave or DC level; 50 mV-1 V into 1 MΩ |
Control Signals | Trigger enabled, trigger out, pass/fail status, fast edge, off |
Connector Type | BNC, located on front |
Probes | |
Probes | Qty. (4) ÷10 Passive Probes |
Probe System | ProBus2. Automatically detects and supports a variety of compatible probes. Fully backwards-compatible to ProBus probes without the use of adapters. |
Scale Factors | Automatically or manually selected depending on probe used |
Calibration Output | Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 500 Hz to 1 MHz square wave; 50 mV to 1.0V. |
Power Requirements | |
Voltage | 90 - 132 Vrms, 380 - 420Hz 90 - 264 Vrms, 47 - 63 Hz |
Nominal Power Consumption | 400W/400VA |
Max. Power Consumption | 525W/525VA |
Certifications | |
Certifications | CE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No. 61010-1-12 |
Environmental | |
Temperature (Operating) | +5 °C to +40 °C |
Temperature (Non-Operating) | -20 °C to +60 °C |
Humidity (Operating) | 5% to 90% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C. |
Humidity (Non-Operating) | 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F |
Altitude (Operating) | Up to 10,000 ft. (3048 m) at or below +30 °C |
Altitude (Non-Operating) | Up to 40,000 ft. (12,192 m) |
Random Vibration (Operating) | 0.31 grms 5 Hz to 500 Hz, 20 minutes in each of three orthogonal axes |
Random Vibration (Non-Operating) | 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes |
Functional Shock | 30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total |
Size and Weight | |
Dimensions (HWD) | 13.6” H x 17.5” W x 7.7” D (345 x 445 x 196 mm) |
Weight | 24.4 lbs (11.1 kg) |
Shipping Weight | 34 lbs |
Warranty and Service | |
Warranty and Service | 3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services. |

Vertical - Analog Channels | |
Analog Bandwidth (Max) | 6 GHz on 2 Ch 4 GHz on 4 Ch |
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input) | 1 GHz (typical) |
Rise Time (10-90%, 50 Ω) | 71 ps |
Rise Time (20-80%, 50 Ω) | 50 ps |
Input Channels | 4 |
Vertical Resolution | 12 bits; up to 15 bits with enhanced resolution (ERES) |
Effective Number of Bits (ENOB) | 7.2 bits |
Vertical Noise Floor (1 mV/div) | 285 µV |
Vertical Noise Floor (2 mV/div) | 285 µV |
Vertical Noise Floor (5 mV/div) | 285 µV |
Vertical Noise Floor (10 mV/div) | 285 µV |
Vertical Noise Floor (20 mV/div) | 360 µV |
Vertical Noise Floor (50 mV/div) | 835 µV |
Vertical Noise Floor (100 mV/div) | 1.70 mV |
Vertical Noise Floor (200 mV/div) | 2.70 mV |
Vertical Noise Floor (500 mV/div) | 6.70 mV |
Vertical Noise Floor (1 V/div) | 11.93 mV |
Sensitivity | 50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable |
DC Vertical Gain Accuracy (Gain Component of DC Accuracy) | ±(0.5%) F.S, offset at 0 V |
Channel-Channel Isolation | 70dB up to 200 MHz 60dB up to 500 MHz 50dB up to 1 GHz 40dB up to 2.5 GHz 30dB up to 6 GHz |
Offset Range | 50 Ω, ≤1 GHz BWL 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-1V: +/-10V 50 Ω, >1 GHz BWL 1mV/div-34.5mV/div: +/- 0.5V 35mV/div-87mV/div: +/- 1.25V 88mV/div-220mV/div: +/-3V 225mV/div-1V/div: +/-5V 1 MΩ 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-100mV: +/-16V 102mV-198mV: +/-80V 200mV-1V: +/-160V 1.02V-10V: +/-400V |
DC Vertical Offset Accuracy | +/-(0.5% of offset value + 0.5%FS + 1mV) |
Maximum Input Voltage | 50 Ω, ≤1 GHz BWL 5V RMS, +/- 10V Peak 50 Ω, >1 GHz BWL '+/-2V max. up to 34.5mV/div +/-5V max. 35mV/div to 87mV/div 5.5Vrms >87mV/div 1 MΩ 400 V max (Peak DC+AC) |
Input Coupling | 1 MΩ: AC, DC, GND; 50 Ω: DC, GND |
Input Impedance | 50 Ω+/-2% or 1 MΩ||14pF, 10 MΩ || 9.5 pF |
Bandwidth Limiters | 20MHz, 200MHz, 500 MHz, 1 GHz, 2.5 GHz, 4 GHz |
Rescaling | Length: meters, inches, feet, yards, miles; Mass: grams, slugs; Temperature: celsius, fahrenheit, kelvin; Angle: radian, arcdegr, arcmin, arcsec, cycles, revolutions, turns; Velocity: m/s, in/s, ft/s, yd/s, miles/s; Acceleration: m/s2, in/s2, ft/s2, g0; Volume: liters, cubic meters, cubic inches, cubic feet, cubic yards; Force (Weight): newton, grain, ounce, pound; Pressure: pascal, bar, atmosphere (technical), atmosphere (standard), torr, psi; Electrical: volts, amps, watts, volt-amperes, volt-amperes reactive, farad, coulomb, ohm, siemen, volt/meter, coulomb/m2, farad/meter, siemen/meter, power factor; Magnetic: weber, tesla, henry, amp/meter, henry/meter; Energy: joule, Btu, calorie; Rotating Machine: radian/second, frequency, revolution/second, revolution/minute, N?m, lb-ft, lb-in, oz-in, watt, horsepower; Other: %. |
Horizontal - Analog Channels | |
Timebases | Internal timebase common to 4 input channels |
Acquisition Modes | Real-time |
Time/Division Range | 20ps/div - 1 ks/div |
Clock Accuracy | +/-100ppb for 5 to 40C + 0.10ppm/year from calibration |
Sample Clock Jitter | up to 10µs Acquired Time Range: 60 fsrms (Internal Timebase Reference) up to 10ms Acquired Time Range: 100 fsrms (Internal Timebase Reference) |
Delta Time Measurement Accuracy | \sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds) |
Jitter Measurement Floor | \sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)} |
Channel-Channel Deskew Range | ±9 x time/div. setting, 100 ms max., each channel |
External Timebase Reference (Input) | 10MHz +/-25ppm at 0 to 10dBm into 50Ohms |
External Timebase Reference (Output) | 10MHz, 5.0 dBm +/-2.5 dBm, sinewave synchronized to reference being used (internal or external reference) |
External Clock | N/A |
Acquisition - Analog Channels | |
Sample Rate (Single-shot) | 10 GS/s on 4 Ch 20 GS/s on 2 Ch |
Sample Rate (Repetitive) | N/A |
Memory Length (4 Ch / 2 Ch / 1Ch) (Number of Segments) | 50M/100M |
Memory Length Options (4 Ch / 2 Ch / 1Ch) (Number of Segments) | WPHD-200MPT Option: 100M / 200M WPHD-500MPT Option: 250M / 500M WPHD-1000MPT Option: 500M / 1000M WPHD-2000MPT Option: 1000M / 2000M WPHD-5000MPT Option: 2500M / 5000M |
Averaging | Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps (Waveforms of ≤500Mpts) |
Envelope (Extrema) | Envelope, floor, or roof for up to 1 million sweeps (Waveforms of ≤500Mpts) |
Interpolation | Linear or Sin x/x (2 pt and 5 pt) (Waveforms of ≤500Mpts) |
Triggering System | |
Modes | Acquisition of ≤500Mpts: Normal, Auto, Single, and Stop Acquisition of >500Mpts: Single |
Sources | Any input channel, Ext, Ext/10, Line, or Fast Edge; slope and level unique to each source (except Line and Fast edge) |
Coupling | DC, AC, HFRej, LFRej |
Pre-trigger Delay | 0-100% of memory size |
Post-trigger Delay | No limitation |
Hold-off | From 1 ns up to 20 s or from 1 to 99,999,999 events |
Trigger and Interpolator Jitter | ≤ 2.5 ps RMS (typical) <0.1 ps RMS (typical, software assisted) |
Internal Trigger Level Range | ±4.1 div from center (typical) |
External Trigger Level Range | Ext (±0.4 V); Ext/10 (±4 V) |
Maximum Trigger Rate | 650,000 waveforms/second (in Sequence Mode, up to 4 channels) |
Trigger Sensitivity with Edge Trigger ProBus Inputs | 0.75 div @ < 5 GHz 1.5 div @ < 6 GHz |
Trigger Sensitivity with Edge Trigger (Aux Input) | 0.5 div @ < 1 GHz |
Max. Trigger Frequency, SMART Trigger | 2.0 GHz @ ≥ 10 mV/div (minimum triggerable width 200 ps) |
Trigger Types | |
Edge | Triggers when signal meets slope (positive, negative, or either) and level condition. |
Width | Triggers on positive or negative glitches with selectable widths. Minimum width 500 ps, maximum width: 20 s |
Glitch | Triggers on positive or negative glitches with selectable widths. Minimum width 200 ps, maximum width: 20 s |
Window | Triggers when signal exits a window defined by adjustable thresholds |
Pattern | Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern. |
TV-Composite Video | Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative). |
Runt | Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns. |
Slew Rate | Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
Interval | Triggers on intervals selectable between 1 ns and 20 s. |
Dropout | Triggers if signal drops out for longer than selected time between 1 ns and 20 s. |
Measurement Trigger | Select from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger. |
Multi-Stage: Qualified (Timeout or State/Edge Qualified) | Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
Triggers with Exclusion Technology | Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met |
Multi-Stage: Qualified First | In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
TriggerScan | A Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially. |
Low Speed Serial Protocol Trigger (Optional) | |
Supported Protocols | I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, MIL-STD-1553, USB 1.x/2.0 |
Measurement Tools | |
Measurement Functionality | Display up to 12 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state. |
Measurement Parameters - Horizontal + Jitter | Cycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min |
Measurement Parameters - Vertical | Amplitude, Base, [email protected], Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top. |
Measurement Parameters - Pulse | Area, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%) |
Measurement Parameters - Statistical (on Histograms) | Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total) |
Math Tools | |
Math Functionality | Display up to 12 math functions traces (F1-F12). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math. |
Math Operators - Basic Math | Average (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+). |
Math Operators - Digital (incl. with MSO models/options) | Digital AND, Digital DFlipFlop, Digital NAND, Digital NOR, Digital NOT, Digital OR, Digital XOR |
Math Operators - Filters | Enhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x. |
Math Operators - Frequency Analysis | FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows. |
Math Operators - Functions | Absolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity). |
Math Operators - Other | Segment, Sparse |
Measurement and Math Integration | |
Measurement and Math Integration | Histograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma) |
Pass/Fail Testing | |
Pass/Fail Testing | Display up to 12 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value <. ≤, =, >, ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook. |
Display System | |
Size | Color 15.6" widescreen capacitive touch screen |
Resolution | 1920 x 1080 pixels |
Number of traces | Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces. |
Grid Styles | Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Quatro, Twelve, Sixteen |
Waveform Representation | Sample dots joined, or sample dots only |
Persistence Display | |
Analog and Color-Graded Persistence | Waveforms of ≤500Mpts: Variable saturation levels; stores each trace’s persistence data in memory |
Persistence Types | Waveforms of ≤500Mpts: Select analog, color, or three-dimensional |
Trace Selection | Waveforms of ≤500Mpts: Activate persistence on all or any combination of traces |
Persistence Aging | Waveforms of ≤500Mpts: Select from 500 ms to infinity |
Sweep Display Modes | Waveforms of ≤500Mpts: All accumulated, or all accumulated with last trace highlighted |
Zoom Expansion Traces | |
Zoom Expansion Traces | Display up to 12 Zoom and 12 Math/Zoom traces |
Internal Waveform Memory | |
Internal Waveform Memory | 12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity. |
Setup Storage | |
Front Panel and Instrument Status | Store to the internal hard drive, over the network, or to a USB-connected peripheral device. |
Automatic Setup | |
Auto Setup | Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals |
Find Vertical Scale | Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range |
Calibration | |
Auto Calibration | Ensures specified DC and timing accuracy is maintained for 1 year minimum. |
Processor/CPU | |
Type | Intel® Core i5-6500 Quad Core, 3.2 GHz (or better) |
Processor Memory | 16 GB standard |
Operating System | Microsoft Windows® 10 |
Oscilloscope Operating Software | Teledyne LeCroy MAUI™ with OneTouch |
Real Time Clock | Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks. |
Connectivity | |
Ethernet Port | 2 x 10/100/1000BaseT Ethernet interface (RJ45 port) |
USB Host Ports | 4 side USB 3.1 Gen1 ports, 3 front USB 3.1 Gen1 ports |
USB Device Port | 1 port - USBTMC over USB 3.1 Gen1 |
GPIB Port (optional) | Supports IEEE - 488.2 (External) |
External Monitor Port | 1 x DisplayPort, supports up to 4096x2304 @ 24 Hz 1 x HDMI, supports up to 4096x2304 @ 60 Hz |
Remote Control | Via Windows Automation, or via LeCroy Remote Command Set |
Network Communication Standard | VXI-11 or VICP, LXI Compatible |
Auxiliary Input | |
Signal Types | For external trigger input |
Coupling | 50 Ω: DC; 1 MΩ: AC, DC, GND |
Max. Input Voltage | 50 Ω 5V RMS, +/- 10V Peak 1 MΩ 400 V max (Peak DC+AC) |
Auxiliary Output | |
Signal Types | Select from outpout signal, control signals, off |
Output Signal | 500 Hz-5 MHz square wave or DC level; 50 mV-1 V into 1 MΩ |
Control Signals | Trigger enabled, trigger out, pass/fail status, fast edge, off |
Connector Type | BNC, located on front |
Probes | |
Probes | Qty. (4) ÷10 Passive Probes |
Probe System | ProBus2. Automatically detects and supports a variety of compatible probes. Fully backwards-compatible to ProBus probes without the use of adapters. |
Scale Factors | Automatically or manually selected depending on probe used |
Calibration Output | Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 500 Hz to 1 MHz square wave; 50 mV to 1.0V. |
Power Requirements | |
Voltage | 90 - 132 Vrms, 380 - 420Hz 90 - 264 Vrms, 47 - 63 Hz |
Nominal Power Consumption | 400W/400VA |
Max. Power Consumption | 525W/525VA |
Certifications | |
Certifications | CE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No. 61010-1-12 |
Environmental | |
Temperature (Operating) | +5 °C to +40 °C |
Temperature (Non-Operating) | -20 °C to +60 °C |
Humidity (Operating) | 5% to 90% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C. |
Humidity (Non-Operating) | 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F |
Altitude (Operating) | Up to 10,000 ft. (3048 m) at or below +30 °C |
Altitude (Non-Operating) | Up to 40,000 ft. (12,192 m) |
Random Vibration (Operating) | 0.31 grms 5 Hz to 500 Hz, 20 minutes in each of three orthogonal axes |
Random Vibration (Non-Operating) | 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes |
Functional Shock | 30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total |
Size and Weight | |
Dimensions (HWD) | 13.6” H x 17.5” W x 7.7” D (345 x 445 x 196 mm) |
Weight | 24.4 lbs (11.1 kg) |
Shipping Weight | 34 lbs |
Warranty and Service | |
Warranty and Service | 3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services. |

Vertical - Analog Channels | |
Analog Bandwidth (Max) | 8 GHz on 2 Ch 4 GHz on 4 Ch |
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input) | 1 GHz (typical) |
Rise Time (10-90%, 50 Ω) | 57.5 ps |
Rise Time (20-80%, 50 Ω) | 40.5 ps |
Input Channels | 4 |
Vertical Resolution | 12 bits; up to 15 bits with enhanced resolution (ERES) |
Effective Number of Bits (ENOB) | 7.0 bits |
Vertical Noise Floor (1 mV/div) | 315 µV |
Vertical Noise Floor (2 mV/div) | 315 µV |
Vertical Noise Floor (5 mV/div) | 315 µV |
Vertical Noise Floor (10 mV/div) | 315 µV |
Vertical Noise Floor (20 mV/div) | 420 µV |
Vertical Noise Floor (50 mV/div) | 983 µV |
Vertical Noise Floor (100 mV/div) | 1.95 mV |
Vertical Noise Floor (200 mV/div) | 3.16 mV |
Vertical Noise Floor (500 mV/div) | 7.76 mV |
Vertical Noise Floor (1 V/div) | 13.81 mV |
Sensitivity | 50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable |
DC Vertical Gain Accuracy (Gain Component of DC Accuracy) | ±(0.5%) F.S, offset at 0 V |
Channel-Channel Isolation | 70dB up to 200 MHz 60dB up to 500 MHz 50dB up to 1 GHz 40dB up to 2.5 GHz 30dB up to 8 GHz |
Offset Range | 50 Ω, ≤1 GHz BWL 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-1V: +/-10V 50 Ω, >1 GHz BWL 1mV/div-34.5mV/div: +/- 0.5V 35mV/div-87mV/div: +/- 1.25V 88mV/div-220mV/div: +/-3V 225mV/div-1V/div: +/-5V 1 MΩ 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-100mV: +/-16V 102mV-198mV: +/-80V 200mV-1V: +/-160V 1.02V-10V: +/-400V |
DC Vertical Offset Accuracy | +/-(0.5% of offset value + 0.5%FS + 1mV) |
Maximum Input Voltage | 50 Ω, ≤1 GHz BWL 5V RMS, +/- 10V Peak 50 Ω, >1 GHz BWL '+/-2V max. up to 34.5mV/div +/-5V max. 35mV/div to 87mV/div 5.5Vrms >87mV/div 1 MΩ 400 V max (Peak DC+AC from DC-20 KHz) Derate at 20 dB/decade to 5.5VRMS, +/-10V Peak above 1.6MHz. The RMS voltage is limited to <142 V for arbitrary waveshapes including DC. |
Input Coupling | 1 MΩ: AC, DC, GND; 50 Ω: DC, GND |
Input Impedance | 50 Ω+/-2% or 1 MΩ||14pF, 10 MΩ || 9.5 pF |
Bandwidth Limiters | 20MHz, 200MHz, 500 MHz, 1 GHz, 2.5 GHz, 4 GHz, 6 GHz |
Rescaling | Length: meters, inches, feet, yards, miles; Mass: grams, slugs; Temperature: celsius, fahrenheit, kelvin; Angle: radian, arcdegr, arcmin, arcsec, cycles, revolutions, turns; Velocity: m/s, in/s, ft/s, yd/s, miles/s; Acceleration: m/s2, in/s2, ft/s2, g0; Volume: liters, cubic meters, cubic inches, cubic feet, cubic yards; Force (Weight): newton, grain, ounce, pound; Pressure: pascal, bar, atmosphere (technical), atmosphere (standard), torr, psi; Electrical: volts, amps, watts, volt-amperes, volt-amperes reactive, farad, coulomb, ohm, siemen, volt/meter, coulomb/m2, farad/meter, siemen/meter, power factor; Magnetic: weber, tesla, henry, amp/meter, henry/meter; Energy: joule, Btu, calorie; Rotating Machine: radian/second, frequency, revolution/second, revolution/minute, N?m, lb-ft, lb-in, oz-in, watt, horsepower; Other: %. |
Horizontal - Analog Channels | |
Timebases | Internal timebase common to 4 input channels |
Acquisition Modes | Real-time |
Time/Division Range | 20ps/div - 1 ks/div |
Clock Accuracy | '+/-60ppb for 5 to 40C + 0.10ppm/year from calibration |
Sample Clock Jitter | up to 10µs Acquired Time Range: 60 fsrms (Internal Timebase Reference) up to 10ms Acquired Time Range: 100 fsrms (Internal Timebase Reference) |
Delta Time Measurement Accuracy | \sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds) |
Jitter Measurement Floor | \sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)} |
Channel-Channel Deskew Range | ±9 x time/div. setting, 100 ms max., each channel |
External Timebase Reference (Input) | 10MHz +/-25ppm at 0 to 10dBm into 50Ohms |
External Timebase Reference (Output) | 10MHz, 5.0 dBm +/-1 dBm, sinewave synchronized to reference being used (internal or external reference) |
External Clock | N/A |
Acquisition - Analog Channels | |
Sample Rate (Single-shot) | 10 GS/s on 4 Ch 20 GS/s on 2 Ch |
Sample Rate (Repetitive) | N/A |
Memory Length (4 Ch / 2 Ch / 1Ch) (Number of Segments) | 50M/100M |
Memory Length Options (4 Ch / 2 Ch / 1Ch) (Number of Segments) | WPHD-200MPT Option: 100M / 200M WPHD-500MPT Option: 250M / 500M WPHD-1000MPT Option: 500M / 1000M WPHD-2000MPT Option: 1000M / 2000M WPHD-5000MPT Option: 2500M / 5000M |
Averaging | Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps (Waveforms of ≤500Mpts) |
Envelope (Extrema) | Envelope, floor, or roof for up to 1 million sweeps (Waveforms of ≤500Mpts) |
Interpolation | Linear or Sin x/x (2 pt and 4 pt) (Waveforms of ≤500Mpts) |
Triggering System | |
Modes | Acquisition of ≤500Mpts: Normal, Auto, Single, and Stop Acquisition of >500Mpts: Single |
Sources | Any input channel, Ext, Ext/10, Line, or Fast Edge; slope and level unique to each source (except line trigger) |
Coupling | DC, AC, HFRej, LFRej |
Pre-trigger Delay | 0-100% of memory size |
Post-trigger Delay | 0-10,000 divisions |
Hold-off | From 1 ns up to 20 s or from 1 to 99,999,999 events |
Trigger and Interpolator Jitter | ≤ 2.5 ps RMS (typical) <0.1 ps RMS (typical, software assisted) |
Internal Trigger Level Range | ±4.1 div from center (typical) |
External Trigger Level Range | Ext (±0.4 V); Ext/10 (±4 V) |
Maximum Trigger Rate | 650,000 waveforms/second (in Sequence Mode, up to 4 channels) |
Trigger Sensitivity with Edge Trigger ProBus Inputs | 2.25 div @ < 8 GHz 1.25 div @ < 4.5 GHz 0.75 div @ < 1 GHz |
Trigger Sensitivity with Edge Trigger (Aux Input) | 0.5 div @ < 1 GHz |
Max. Trigger Frequency, SMART Trigger | 2.0 GHz @ ≥ 10 mV/div (minimum triggerable width 200 ps) |
Trigger Types | |
Edge | Triggers when signal meets slope (positive, negative, or either) and level condition. |
Width | Triggers on positive or negative glitches with selectable widths. Minimum width 500 ps, maximum width: 20 s |
Glitch | Triggers on positive or negative glitches with selectable widths. Minimum width 200 ps, maximum width: 20 s |
Window | Triggers when signal exits a window defined by adjustable thresholds |
Pattern | Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern. |
TV-Composite Video | Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative). |
Runt | Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns. |
Slew Rate | Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
Interval | Triggers on intervals selectable between 1 ns and 20 s. |
Dropout | Triggers if signal drops out for longer than selected time between 1 ns and 20 s. |
Measurement Trigger | Select from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger. |
Multi-Stage: Qualified (Timeout or State/Edge Qualified) | Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
Triggers with Exclusion Technology | Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met |
Multi-Stage: Qualified First | In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
TriggerScan | A Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially. |
Low Speed Serial Protocol Trigger (Optional) | |
Supported Protocols | I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, MIL-STD-1553, USB 1.x/2.0 |
Measurement Tools | |
Measurement Functionality | Display up to 12 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state. |
Measurement Parameters - Horizontal + Jitter | Cycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min |
Measurement Parameters - Vertical | Amplitude, Base, [email protected], Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top. |
Measurement Parameters - Pulse | Area, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%) |
Measurement Parameters - Statistical (on Histograms) | Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total) |
Math Tools | |
Math Functionality | Display up to 12 math functions traces (F1-F12). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math. |
Math Operators - Basic Math | Average (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+). |
Math Operators - Digital (incl. with MSO models/options) | Digital AND, Digital DFlipFlop, Digital NAND, Digital NOR, Digital NOT, Digital OR, Digital XOR |
Math Operators - Filters | Enhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x. |
Math Operators - Frequency Analysis | FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows. |
Math Operators - Functions | Absolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity). |
Math Operators - Other | Segment, Sparse |
Measurement and Math Integration | |
Measurement and Math Integration | Histograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma) |
Pass/Fail Testing | |
Pass/Fail Testing | Display up to 12 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value <. ≤, =, >, ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook. |
Display System | |
Size | Color 15.6" widescreen capacitive touch screen |
Resolution | 1920 x 1080 pixels |
Number of traces | Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces. |
Grid Styles | Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Quatro, Twelve, Sixteen |
Waveform Representation | Sample dots joined, or sample dots only |
Persistence Display | |
Analog and Color-Graded Persistence | Waveforms of ≤500Mpts: Variable saturation levels; stores each trace’s persistence data in memory |
Persistence Types | Waveforms of ≤500Mpts: Select analog, color, or three-dimensional |
Trace Selection | Waveforms of ≤500Mpts: Activate persistence on all or any combination of traces |
Persistence Aging | Waveforms of ≤500Mpts: Select from 500 ms to infinity |
Sweep Display Modes | Waveforms of ≤500Mpts: All accumulated, or all accumulated with last trace highlighted |
Zoom Expansion Traces | |
Zoom Expansion Traces | Display up to 12 Zoom and 12 Math/Zoom traces |
Internal Waveform Memory | |
Internal Waveform Memory | 12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity. |
Setup Storage | |
Front Panel and Instrument Status | Store to the internal hard drive, over the network, or to a USB-connected peripheral device. |
Automatic Setup | |
Auto Setup | Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals |
Find Vertical Scale | Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range |
Calibration | |
Auto Calibration | Ensures specified DC and timing accuracy is maintained for 1 year minimum. |
Processor/CPU | |
Type | Intel® Core i5-6500 Quad Core, 3.2 GHz (or better) |
Processor Memory | 16 GB standard |
Operating System | Microsoft Windows® 10 |
Oscilloscope Operating Software | Teledyne LeCroy MAUI™ with OneTouch |
Real Time Clock | Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks. |
Connectivity | |
Ethernet Port | 2 x 10/100/1000BaseT Ethernet interface (RJ45 port) |
USB Host Ports | 4 side USB 3.1 Gen1 ports, 3 front USB 3.1 Gen1 ports |
USB Device Port | 1 port - USBTMC over USB 3.1 Gen1 |
GPIB Port (optional) | Supports IEEE - 488.2 (External) |
External Monitor Port | 1 x DisplayPort, supports up to 4096x2304 @ 24 Hz 1 x HDMI, supports up to 4096x2304 @ 60 Hz |
Remote Control | Via Windows Automation, or via LeCroy Remote Command Set |
Network Communication Standard | VXI-11 or VICP, LXI Compatible |
Auxiliary Input | |
Signal Types | For external trigger input |
Coupling | 50 Ω: DC; 1 MΩ: AC, DC, GND |
Max. Input Voltage | 50 Ω 5V RMS, +/- 10V Peak 1 MΩ 400 V max (Peak DC+AC) |
Auxiliary Output | |
Signal Types | Select from outpout signal, control signals, off |
Output Signal | 500 Hz-5 MHz square wave or DC level; 50 mV-1 V into 1 MΩ |
Control Signals | Trigger enabled, trigger out, pass/fail status, fast edge, off |
Connector Type | BNC, located on front |
Probes | |
Probes | Qty. (4) ÷10 Passive Probes |
Probe System | ProBus2. Automatically detects and supports a variety of compatible probes. Fully backwards-compatible to ProBus probes without the use of adapters. |
Scale Factors | Automatically or manually selected depending on probe used |
Calibration Output | Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 500 Hz to 1 MHz square wave; 50 mV to 1.0V. |
Power Requirements | |
Voltage | 90 - 132 Vrms, 380 - 420Hz 90 - 264 Vrms, 47 - 63 Hz |
Nominal Power Consumption | 400W/400VA |
Max. Power Consumption | 525W/525VA |
Certifications | |
Certifications | CE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No. 61010-1-12 |
Environmental | |
Temperature (Operating) | +5 °C to +40 °C |
Temperature (Non-Operating) | -20 °C to +60 °C |
Humidity (Operating) | 5% to 90% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C. |
Humidity (Non-Operating) | 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F |
Altitude (Operating) | Up to 10,000 ft. (3048 m) at or below +30 °C |
Altitude (Non-Operating) | Up to 40,000 ft. (12,192 m) |
Random Vibration (Operating) | 0.31 grms 5 Hz to 500 Hz, 20 minutes in each of three orthogonal axes |
Random Vibration (Non-Operating) | 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes |
Functional Shock | 30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total |
Size and Weight | |
Dimensions (HWD) | 13.6” H x 17.5” W x 7.7” D (345 x 445 x 196 mm) |
Weight | 24.4 lbs (11.1 kg) |
Shipping Weight | 34 lbs |
Warranty and Service | |
Warranty and Service | 3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services. |

Vertical - Analog Channels | |
Analog Bandwidth (Max) | 2.5 GHz |
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input) | 1 GHz (typical) |
Rise Time (10-90%, 50 Ω) | 166 ps |
Rise Time (20-80%, 50 Ω) | 117 ps |
Input Channels | 4 |
Vertical Resolution | 12 bits; up to 15 bits with enhanced resolution (ERES) |
Effective Number of Bits (ENOB) | 7.8 bits |
Vertical Noise Floor (1 mV/div) | 155 µV |
Vertical Noise Floor (2 mV/div) | 155 µV |
Vertical Noise Floor (5 mV/div) | 155 µV |
Vertical Noise Floor (10 mV/div) | 155 µV |
Vertical Noise Floor (20 mV/div) | 191 µV |
Vertical Noise Floor (50 mV/div) | 429 µV |
Vertical Noise Floor (100 mV/div) | 889 µV |
Vertical Noise Floor (200 mV/div) | 1.44 mV |
Vertical Noise Floor (500 mV/div) | 3.66 mV |
Vertical Noise Floor (1 V/div) | 6.70 mV |
Sensitivity | 50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable |
DC Vertical Gain Accuracy (Gain Component of DC Accuracy) | ±(0.5%) F.S, offset at 0 V |
Channel-Channel Isolation | 70dB up to 200 MHz 60dB up to 500 MHz 50dB up to 1 GHz 40dB up to 2.5 GHz |
Offset Range | 50 Ω, ≤1 GHz BWL 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-1V: +/-10V 50 Ω, >1 GHz BWL 1mV/div-34.5mV/div: +/- 0.5V 35mV/div-87mV/div: +/- 1.25V 88mV/div-220mV/div: +/-3V 225mV/div-1V/div: +/-5V 1 MΩ 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-100mV: +/-16V 102mV-198mV: +/-80V 200mV-1V: +/-160V 1.02V-10V: +/-400V |
DC Vertical Offset Accuracy | +/-(0.5% of offset value + 0.5%FS + 1mV) |
Maximum Input Voltage | 50 Ω, ≤1 GHz BWL 5V RMS, +/- 10V Peak 50 Ω, >1 GHz BWL '+/-2V max. up to 34.5mV/div +/-5V max. 35mV/div to 87mV/div 5.5Vrms >87mV/div 1 MΩ 400 V max (Peak DC+AC) |
Input Coupling | 1 MΩ: AC, DC, GND; 50 Ω: DC, GND |
Input Impedance | 50 Ω+/-2% or 1 MΩ||14pF, 10 MΩ || 9.5 pF |
Bandwidth Limiters | 20MHz, 200MHz, 500 MHz, 1 GHz |
Rescaling | Length: meters, inches, feet, yards, miles; Mass: grams, slugs; Temperature: celsius, fahrenheit, kelvin; Angle: radian, arcdegr, arcmin, arcsec, cycles, revolutions, turns; Velocity: m/s, in/s, ft/s, yd/s, miles/s; Acceleration: m/s2, in/s2, ft/s2, g0; Volume: liters, cubic meters, cubic inches, cubic feet, cubic yards; Force (Weight): newton, grain, ounce, pound; Pressure: pascal, bar, atmosphere (technical), atmosphere (standard), torr, psi; Electrical: volts, amps, watts, volt-amperes, volt-amperes reactive, farad, coulomb, ohm, siemen, volt/meter, coulomb/m2, farad/meter, siemen/meter, power factor; Magnetic: weber, tesla, henry, amp/meter, henry/meter; Energy: joule, Btu, calorie; Rotating Machine: radian/second, frequency, revolution/second, revolution/minute, N?m, lb-ft, lb-in, oz-in, watt, horsepower; Other: %. |
Horizontal - Analog Channels | |
Timebases | Internal timebase common to 4 input channels |
Acquisition Modes | Real-time |
Time/Division Range | 20ps/div - 1 ks/div |
Clock Accuracy | +/-100ppb for 5 to 40C + 0.10ppm/year from calibration |
Sample Clock Jitter | up to 10µs Acquired Time Range: 60 fsrms (Internal Timebase Reference) up to 10ms Acquired Time Range: 100 fsrms (Internal Timebase Reference) |
Delta Time Measurement Accuracy | \sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds) |
Jitter Measurement Floor | \sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)} |
Channel-Channel Deskew Range | ±9 x time/div. setting, 100 ms max., each channel |
External Timebase Reference (Input) | 10MHz +/-25ppm at 0 to 10dBm into 50Ohms |
External Timebase Reference (Output) | 10MHz, 5.0 dBm +/-2.5 dBm, sinewave synchronized to reference being used (internal or external reference) |
External Clock | N/A |
Acquisition - Analog Channels | |
Sample Rate (Single-shot) | 10 GS/s on 4 Ch 20 GS/s on 2 Ch |
Sample Rate (Repetitive) | N/A |
Memory Length (4 Ch / 2 Ch / 1Ch) (Number of Segments) | 50M/100M |
Memory Length Options (4 Ch / 2 Ch / 1Ch) (Number of Segments) | WPHD-200MPT Option: 100M / 200M WPHD-500MPT Option: 250M / 500M WPHD-1000MPT Option: 500M / 1000M WPHD-2000MPT Option: 1000M / 2000M WPHD-5000MPT Option: 2500M / 5000M |
Averaging | Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps (Waveforms of ≤500Mpts) |
Envelope (Extrema) | Envelope, floor, or roof for up to 1 million sweeps (Waveforms of ≤500Mpts) |
Interpolation | Linear or Sin x/x (2 pt and 5 pt) (Waveforms of ≤500Mpts) |
Vertical, Horizontal, Acquisition - Digital Channels | |
Maximum Input Frequency | 250 MHz |
Minimum Detectable Pulse Width | 2 ns |
Input Channels | 16 Digital channels |
Input Impedance (Flying Leads) | 100 kΩ || 5 pF |
Input Dynamic Range | ± 20V |
Maximum Input Voltage | ±30V Peak |
Maximum Input Voltage Swing | 400mV |
Threshold Groupings | Pod 2: D15 - D8, Pod 1: D7 - D0 |
Threshold Selections | TTL, ECL, CMOS (2.5 V, 3.3 V, 5 V), PECL, LVDS or User Defined |
Threshold Accuracy | ±(3% of threshold setting + 100mV) |
User Defined Threshold Range | ±10 V in 20 mV steps |
User Defined Hysteresis Range | 100 mV to 1.4 V in 100 mV steps |
Sample Rate | 1.25 GS/s |
Record Length | Standard: 50M WPHD-200MPT Option: 100M WPHD-500MPT Option: 125M WPHD-1000MPT Option: 125M WPHD-2000MPT Option: 125M WPHD-5000MPT Option: 125M |
Channel-to-Channel Skew | 350ps |
Triggering System | |
Modes | Acquisition of ≤500Mpts: Normal, Auto, Single, and Stop Acquisition of >500Mpts: Single |
Sources | Any input channel, Ext, Ext/10, Line, or Fast Edge; slope and level unique to each source (except Line and Fast edge) |
Coupling | DC, AC, HFRej, LFRej |
Pre-trigger Delay | 0-100% of memory size |
Post-trigger Delay | No limitation |
Hold-off | From 1 ns up to 20 s or from 1 to 99,999,999 events |
Trigger and Interpolator Jitter | ≤ 2.5 ps RMS (typical) <0.1 ps RMS (typical, software assisted) |
Internal Trigger Level Range | ±4.1 div from center (typical) |
External Trigger Level Range | Ext (±0.4 V); Ext/10 (±4 V) |
Maximum Trigger Rate | 650,000 waveforms/second (in Sequence Mode, up to 4 channels) |
Trigger Sensitivity with Edge Trigger ProBus Inputs | 0.75 div |
Trigger Sensitivity with Edge Trigger (Aux Input) | 0.5 div @ < 1 GHz |
Max. Trigger Frequency, SMART Trigger | 2.0 GHz @ ≥ 10 mV/div (minimum triggerable width 200 ps) |
Trigger Types | |
Edge | Triggers when signal meets slope (positive, negative, or either) and level condition. |
Width | Triggers on positive or negative glitches with selectable widths. Minimum width 500 ps, maximum width: 20 s |
Glitch | Triggers on positive or negative glitches with selectable widths. Minimum width 200 ps, maximum width: 20 s |
Window | Triggers when signal exits a window defined by adjustable thresholds |
Pattern | Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern. |
TV-Composite Video | Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative). |
Runt | Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns. |
Slew Rate | Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
Interval | Triggers on intervals selectable between 1 ns and 20 s. |
Dropout | Triggers if signal drops out for longer than selected time between 1 ns and 20 s. |
Measurement Trigger | Select from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger. |
Multi-Stage: Qualified (Timeout or State/Edge Qualified) | Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
Triggers with Exclusion Technology | Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met |
Multi-Stage: Qualified First | In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
TriggerScan | A Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially. |
Low Speed Serial Protocol Trigger (Optional) | |
Supported Protocols | I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, MIL-STD-1553, USB 1.x/2.0 |
Measurement Tools | |
Measurement Functionality | Display up to 12 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state. |
Measurement Parameters - Horizontal + Jitter | Cycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min |
Measurement Parameters - Vertical | Amplitude, Base, [email protected], Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top. |
Measurement Parameters - Pulse | Area, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%) |
Measurement Parameters - Statistical (on Histograms) | Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total) |
Math Tools | |
Math Functionality | Display up to 12 math functions traces (F1-F12). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math. |
Math Operators - Basic Math | Average (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+). |
Math Operators - Digital (incl. with MSO models/options) | Digital AND, Digital DFlipFlop, Digital NAND, Digital NOR, Digital NOT, Digital OR, Digital XOR |
Math Operators - Filters | Enhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x. |
Math Operators - Frequency Analysis | FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows. |
Math Operators - Functions | Absolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity). |
Math Operators - Other | Segment, Sparse |
Measurement and Math Integration | |
Measurement and Math Integration | Histograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma) |
Pass/Fail Testing | |
Pass/Fail Testing | Display up to 12 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value <. ≤, =, >, ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook. |
Display System | |
Size | Color 15.6" widescreen capacitive touch screen |
Resolution | 1920 x 1080 pixels |
Number of traces | Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces. |
Grid Styles | Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Quatro, Twelve, Sixteen |
Waveform Representation | Sample dots joined, or sample dots only |
Persistence Display | |
Analog and Color-Graded Persistence | Waveforms of ≤500Mpts: Variable saturation levels; stores each trace’s persistence data in memory |
Persistence Types | Waveforms of ≤500Mpts: Select analog, color, or three-dimensional |
Trace Selection | Waveforms of ≤500Mpts: Activate persistence on all or any combination of traces |
Persistence Aging | Waveforms of ≤500Mpts: Select from 500 ms to infinity |
Sweep Display Modes | Waveforms of ≤500Mpts: All accumulated, or all accumulated with last trace highlighted |
Zoom Expansion Traces | |
Zoom Expansion Traces | Display up to 12 Zoom and 12 Math/Zoom traces |
Internal Waveform Memory | |
Internal Waveform Memory | 12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity. |
Setup Storage | |
Front Panel and Instrument Status | Store to the internal hard drive, over the network, or to a USB-connected peripheral device. |
Automatic Setup | |
Auto Setup | Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals |
Find Vertical Scale | Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range |
Calibration | |
Auto Calibration | Ensures specified DC and timing accuracy is maintained for 1 year minimum. |
Processor/CPU | |
Type | Intel® Core i5-6500 Quad Core, 3.2 GHz (or better) |
Processor Memory | 16 GB standard |
Operating System | Microsoft Windows® 10 |
Oscilloscope Operating Software | Teledyne LeCroy MAUI™ with OneTouch |
Real Time Clock | Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks. |
Connectivity | |
Ethernet Port | 2 x 10/100/1000BaseT Ethernet interface (RJ45 port) |
USB Host Ports | 4 side USB 3.1 Gen1 ports, 3 front USB 3.1 Gen1 ports |
USB Device Port | 1 port - USBTMC over USB 3.1 Gen1 |
GPIB Port (optional) | Supports IEEE - 488.2 (External) |
External Monitor Port | 1 x DisplayPort, supports up to 4096x2304 @ 24 Hz 1 x HDMI, supports up to 4096x2304 @ 60 Hz |
Remote Control | Via Windows Automation, or via LeCroy Remote Command Set |
Network Communication Standard | VXI-11 or VICP, LXI Compatible |
Auxiliary Input | |
Signal Types | For external trigger input |
Coupling | 50 Ω: DC; 1 MΩ: AC, DC, GND |
Max. Input Voltage | 50 Ω 5V RMS, +/- 10V Peak 1 MΩ 400 V max (Peak DC+AC) |
Auxiliary Output | |
Signal Types | Select from outpout signal, control signals, off |
Output Signal | 500 Hz-5 MHz square wave or DC level; 50 mV-1 V into 1 MΩ |
Control Signals | Trigger enabled, trigger out, pass/fail status, fast edge, off |
Connector Type | BNC, located on front |
Probes | |
Probes | Qty. (4) ÷10 Passive Probes |
Probe System | ProBus2. Automatically detects and supports a variety of compatible probes. Fully backwards-compatible to ProBus probes without the use of adapters. |
Scale Factors | Automatically or manually selected depending on probe used |
Calibration Output | Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 500 Hz to 1 MHz square wave; 50 mV to 1.0V. |
Power Requirements | |
Voltage | 90 - 132 Vrms, 380 - 420Hz 90 - 264 Vrms, 47 - 63 Hz |
Nominal Power Consumption | 400W/400VA |
Max. Power Consumption | 525W/525VA |
Certifications | |
Certifications | CE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No. 61010-1-12 |
Environmental | |
Temperature (Operating) | +5 °C to +40 °C |
Temperature (Non-Operating) | -20 °C to +60 °C |
Humidity (Operating) | 5% to 90% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C. |
Humidity (Non-Operating) | 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F |
Altitude (Operating) | Up to 10,000 ft. (3048 m) at or below +30 °C |
Altitude (Non-Operating) | Up to 40,000 ft. (12,192 m) |
Random Vibration (Operating) | 0.31 grms 5 Hz to 500 Hz, 20 minutes in each of three orthogonal axes |
Random Vibration (Non-Operating) | 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes |
Functional Shock | 30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total |
Size and Weight | |
Dimensions (HWD) | 13.6” H x 17.5” W x 7.7” D (345 x 445 x 196 mm) |
Weight | 24.4 lbs (11.1 kg) |
Shipping Weight | 34 lbs |
Warranty and Service | |
Warranty and Service | 3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services. |

Vertical - Analog Channels | |
Analog Bandwidth (Max) | 4 GHz |
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input) | 1 GHz (typical) |
Rise Time (10-90%, 50 Ω) | 104 ps |
Rise Time (20-80%, 50 Ω) | 73 ps |
Input Channels | 4 |
Vertical Resolution | 12 bits; up to 15 bits with enhanced resolution (ERES) |
Effective Number of Bits (ENOB) | 7.5 bits |
Vertical Noise Floor (1 mV/div) | 228 µV |
Vertical Noise Floor (2 mV/div) | 228 µV |
Vertical Noise Floor (5 mV/div) | 228 µV |
Vertical Noise Floor (10 mV/div) | 228 µV |
Vertical Noise Floor (20 mV/div) | 275 µV |
Vertical Noise Floor (50 mV/div) | 633 µV |
Vertical Noise Floor (100 mV/div) | 1.31 mV |
Vertical Noise Floor (200 mV/div) | 2.06 mV |
Vertical Noise Floor (500 mV/div) | 5.16 mV |
Vertical Noise Floor (1 V/div) | 9.17 mV |
Sensitivity | 50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable |
DC Vertical Gain Accuracy (Gain Component of DC Accuracy) | ±(0.5%) F.S, offset at 0 V |
Channel-Channel Isolation | 70dB up to 200 MHz 60dB up to 500 MHz 50dB up to 1 GHz 40dB up to 2.5 GHz 30dB up to 4 GHz |
Offset Range | 50 Ω, ≤1 GHz BWL 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-1V: +/-10V 50 Ω, >1 GHz BWL 1mV/div-34.5mV/div: +/- 0.5V 35mV/div-87mV/div: +/- 1.25V 88mV/div-220mV/div: +/-3V 225mV/div-1V/div: +/-5V 1 MΩ 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-100mV: +/-16V 102mV-198mV: +/-80V 200mV-1V: +/-160V 1.02V-10V: +/-400V |
DC Vertical Offset Accuracy | +/-(0.5% of offset value + 0.5%FS + 1mV) |
Maximum Input Voltage | 50 Ω, ≤1 GHz BWL 5V RMS, +/- 10V Peak 50 Ω, >1 GHz BWL '+/-2V max. up to 34.5mV/div +/-5V max. 35mV/div to 87mV/div 5.5Vrms >87mV/div 1 MΩ 400 V max (Peak DC+AC) |
Input Coupling | 1 MΩ: AC, DC, GND; 50 Ω: DC, GND |
Input Impedance | 50 Ω+/-2% or 1 MΩ||14pF, 10 MΩ || 9.5 pF |
Bandwidth Limiters | 20MHz, 200MHz, 500 MHz, 1 GHz, 2.5 GHz |
Rescaling | Length: meters, inches, feet, yards, miles; Mass: grams, slugs; Temperature: celsius, fahrenheit, kelvin; Angle: radian, arcdegr, arcmin, arcsec, cycles, revolutions, turns; Velocity: m/s, in/s, ft/s, yd/s, miles/s; Acceleration: m/s2, in/s2, ft/s2, g0; Volume: liters, cubic meters, cubic inches, cubic feet, cubic yards; Force (Weight): newton, grain, ounce, pound; Pressure: pascal, bar, atmosphere (technical), atmosphere (standard), torr, psi; Electrical: volts, amps, watts, volt-amperes, volt-amperes reactive, farad, coulomb, ohm, siemen, volt/meter, coulomb/m2, farad/meter, siemen/meter, power factor; Magnetic: weber, tesla, henry, amp/meter, henry/meter; Energy: joule, Btu, calorie; Rotating Machine: radian/second, frequency, revolution/second, revolution/minute, N?m, lb-ft, lb-in, oz-in, watt, horsepower; Other: %. |
Horizontal - Analog Channels | |
Timebases | Internal timebase common to 4 input channels |
Acquisition Modes | Real-time |
Time/Division Range | 20ps/div - 1 ks/div |
Clock Accuracy | +/-100ppb for 5 to 40C + 0.10ppm/year from calibration |
Sample Clock Jitter | up to 10µs Acquired Time Range: 60 fsrms (Internal Timebase Reference) up to 10ms Acquired Time Range: 100 fsrms (Internal Timebase Reference) |
Delta Time Measurement Accuracy | \sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds) |
Jitter Measurement Floor | \sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)} |
Channel-Channel Deskew Range | ±9 x time/div. setting, 100 ms max., each channel |
External Timebase Reference (Input) | 10MHz +/-25ppm at 0 to 10dBm into 50Ohms |
External Timebase Reference (Output) | 10MHz, 5.0 dBm +/-2.5 dBm, sinewave synchronized to reference being used (internal or external reference) |
External Clock | N/A |
Acquisition - Analog Channels | |
Sample Rate (Single-shot) | 10 GS/s on 4 Ch 20 GS/s on 2 Ch |
Sample Rate (Repetitive) | N/A |
Memory Length (4 Ch / 2 Ch / 1Ch) (Number of Segments) | 50M/100M |
Memory Length Options (4 Ch / 2 Ch / 1Ch) (Number of Segments) | WPHD-200MPT Option: 100M / 200M WPHD-500MPT Option: 250M / 500M WPHD-1000MPT Option: 500M / 1000M WPHD-2000MPT Option: 1000M / 2000M WPHD-5000MPT Option: 2500M / 5000M |
Averaging | Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps (Waveforms of ≤500Mpts) |
Envelope (Extrema) | Envelope, floor, or roof for up to 1 million sweeps (Waveforms of ≤500Mpts) |
Interpolation | Linear or Sin x/x (2 pt and 5 pt) (Waveforms of ≤500Mpts) |
Vertical, Horizontal, Acquisition - Digital Channels | |
Maximum Input Frequency | 250 MHz |
Minimum Detectable Pulse Width | 2 ns |
Input Channels | 16 Digital channels |
Input Impedance (Flying Leads) | 100 kΩ || 5 pF |
Input Dynamic Range | ± 20V |
Maximum Input Voltage | ±30V Peak |
Maximum Input Voltage Swing | 400mV |
Threshold Groupings | Pod 2: D15 - D8, Pod 1: D7 - D0 |
Threshold Selections | TTL, ECL, CMOS (2.5 V, 3.3 V, 5 V), PECL, LVDS or User Defined |
Threshold Accuracy | ±(3% of threshold setting + 100mV) |
User Defined Threshold Range | ±10 V in 20 mV steps |
User Defined Hysteresis Range | 100 mV to 1.4 V in 100 mV steps |
Sample Rate | 1.25 GS/s |
Record Length | Standard: 50M WPHD-200MPT Option: 100M WPHD-500MPT Option: 125M WPHD-1000MPT Option: 125M WPHD-2000MPT Option: 125M WPHD-5000MPT Option: 125M |
Channel-to-Channel Skew | 350ps |
Triggering System | |
Modes | Acquisition of ≤500Mpts: Normal, Auto, Single, and Stop Acquisition of >500Mpts: Single |
Sources | Any input channel, Ext, Ext/10, Line, or Fast Edge; slope and level unique to each source (except Line and Fast edge) |
Coupling | DC, AC, HFRej, LFRej |
Pre-trigger Delay | 0-100% of memory size |
Post-trigger Delay | No limitation |
Hold-off | From 1 ns up to 20 s or from 1 to 99,999,999 events |
Trigger and Interpolator Jitter | ≤ 2.5 ps RMS (typical) <0.1 ps RMS (typical, software assisted) |
Internal Trigger Level Range | ±4.1 div from center (typical) |
External Trigger Level Range | Ext (±0.4 V); Ext/10 (±4 V) |
Maximum Trigger Rate | 650,000 waveforms/second (in Sequence Mode, up to 4 channels) |
Trigger Sensitivity with Edge Trigger ProBus Inputs | 0.75 div |
Trigger Sensitivity with Edge Trigger (Aux Input) | 0.5 div @ < 1 GHz |
Max. Trigger Frequency, SMART Trigger | 2.0 GHz @ ≥ 10 mV/div (minimum triggerable width 200 ps) |
Trigger Types | |
Edge | Triggers when signal meets slope (positive, negative, or either) and level condition. |
Width | Triggers on positive or negative glitches with selectable widths. Minimum width 500 ps, maximum width: 20 s |
Glitch | Triggers on positive or negative glitches with selectable widths. Minimum width 200 ps, maximum width: 20 s |
Window | Triggers when signal exits a window defined by adjustable thresholds |
Pattern | Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern. |
TV-Composite Video | Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative). |
Runt | Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns. |
Slew Rate | Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
Interval | Triggers on intervals selectable between 1 ns and 20 s. |
Dropout | Triggers if signal drops out for longer than selected time between 1 ns and 20 s. |
Measurement Trigger | Select from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger. |
Multi-Stage: Qualified (Timeout or State/Edge Qualified) | Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
Triggers with Exclusion Technology | Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met |
Multi-Stage: Qualified First | In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
TriggerScan | A Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially. |
Low Speed Serial Protocol Trigger (Optional) | |
Supported Protocols | I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, MIL-STD-1553, USB 1.x/2.0 |
Measurement Tools | |
Measurement Functionality | Display up to 12 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state. |
Measurement Parameters - Horizontal + Jitter | Cycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min |
Measurement Parameters - Vertical | Amplitude, Base, [email protected], Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top. |
Measurement Parameters - Pulse | Area, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%) |
Measurement Parameters - Statistical (on Histograms) | Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total) |
Math Tools | |
Math Functionality | Display up to 12 math functions traces (F1-F12). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math. |
Math Operators - Basic Math | Average (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+). |
Math Operators - Digital (incl. with MSO models/options) | Digital AND, Digital DFlipFlop, Digital NAND, Digital NOR, Digital NOT, Digital OR, Digital XOR |
Math Operators - Filters | Enhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x. |
Math Operators - Frequency Analysis | FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows. |
Math Operators - Functions | Absolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity). |
Math Operators - Other | Segment, Sparse |
Measurement and Math Integration | |
Measurement and Math Integration | Histograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma) |
Pass/Fail Testing | |
Pass/Fail Testing | Display up to 12 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value <. ≤, =, >, ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook. |
Display System | |
Size | Color 15.6" widescreen capacitive touch screen |
Resolution | 1920 x 1080 pixels |
Number of traces | Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces. |
Grid Styles | Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Quatro, Twelve, Sixteen |
Waveform Representation | Sample dots joined, or sample dots only |
Persistence Display | |
Analog and Color-Graded Persistence | Waveforms of ≤500Mpts: Variable saturation levels; stores each trace’s persistence data in memory |
Persistence Types | Waveforms of ≤500Mpts: Select analog, color, or three-dimensional |
Trace Selection | Waveforms of ≤500Mpts: Activate persistence on all or any combination of traces |
Persistence Aging | Waveforms of ≤500Mpts: Select from 500 ms to infinity |
Sweep Display Modes | Waveforms of ≤500Mpts: All accumulated, or all accumulated with last trace highlighted |
Zoom Expansion Traces | |
Zoom Expansion Traces | Display up to 12 Zoom and 12 Math/Zoom traces |
Internal Waveform Memory | |
Internal Waveform Memory | 12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity. |
Setup Storage | |
Front Panel and Instrument Status | Store to the internal hard drive, over the network, or to a USB-connected peripheral device. |
Automatic Setup | |
Auto Setup | Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals |
Find Vertical Scale | Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range |
Calibration | |
Auto Calibration | Ensures specified DC and timing accuracy is maintained for 1 year minimum. |
Processor/CPU | |
Type | Intel® Core i5-6500 Quad Core, 3.2 GHz (or better) |
Processor Memory | 16 GB standard |
Operating System | Microsoft Windows® 10 |
Oscilloscope Operating Software | Teledyne LeCroy MAUI™ with OneTouch |
Real Time Clock | Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks. |
Connectivity | |
Ethernet Port | 2 x 10/100/1000BaseT Ethernet interface (RJ45 port) |
USB Host Ports | 4 side USB 3.1 Gen1 ports, 3 front USB 3.1 Gen1 ports |
USB Device Port | 1 port - USBTMC over USB 3.1 Gen1 |
GPIB Port (optional) | Supports IEEE - 488.2 (External) |
External Monitor Port | 1 x DisplayPort, supports up to 4096x2304 @ 24 Hz 1 x HDMI, supports up to 4096x2304 @ 60 Hz |
Remote Control | Via Windows Automation, or via LeCroy Remote Command Set |
Network Communication Standard | VXI-11 or VICP, LXI Compatible |
Auxiliary Input | |
Signal Types | For external trigger input |
Coupling | 50 Ω: DC; 1 MΩ: AC, DC, GND |
Max. Input Voltage | 50 Ω 5V RMS, +/- 10V Peak 1 MΩ 400 V max (Peak DC+AC) |
Auxiliary Output | |
Signal Types | Select from outpout signal, control signals, off |
Output Signal | 500 Hz-5 MHz square wave or DC level; 50 mV-1 V into 1 MΩ |
Control Signals | Trigger enabled, trigger out, pass/fail status, fast edge, off |
Connector Type | BNC, located on front |
Probes | |
Probes | Qty. (4) ÷10 Passive Probes |
Probe System | ProBus2. Automatically detects and supports a variety of compatible probes. Fully backwards-compatible to ProBus probes without the use of adapters. |
Scale Factors | Automatically or manually selected depending on probe used |
Calibration Output | Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 500 Hz to 1 MHz square wave; 50 mV to 1.0V. |
Power Requirements | |
Voltage | 90 - 132 Vrms, 380 - 420Hz 90 - 264 Vrms, 47 - 63 Hz |
Nominal Power Consumption | 400W/400VA |
Max. Power Consumption | 525W/525VA |
Certifications | |
Certifications | CE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No. 61010-1-12 |
Environmental | |
Temperature (Operating) | +5 °C to +40 °C |
Temperature (Non-Operating) | -20 °C to +60 °C |
Humidity (Operating) | 5% to 90% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C. |
Humidity (Non-Operating) | 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F |
Altitude (Operating) | Up to 10,000 ft. (3048 m) at or below +30 °C |
Altitude (Non-Operating) | Up to 40,000 ft. (12,192 m) |
Random Vibration (Operating) | 0.31 grms 5 Hz to 500 Hz, 20 minutes in each of three orthogonal axes |
Random Vibration (Non-Operating) | 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes |
Functional Shock | 30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total |
Size and Weight | |
Dimensions (HWD) | 13.6” H x 17.5” W x 7.7” D (345 x 445 x 196 mm) |
Weight | 24.4 lbs (11.1 kg) |
Shipping Weight | 34 lbs |
Warranty and Service | |
Warranty and Service | 3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services. |

Vertical - Analog Channels | |
Analog Bandwidth (Max) | 6 GHz on 2 Ch 4 GHz on 4 Ch |
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input) | 1 GHz (typical) |
Rise Time (10-90%, 50 Ω) | 71 ps |
Rise Time (20-80%, 50 Ω) | 50 ps |
Input Channels | 4 |
Vertical Resolution | 12 bits; up to 15 bits with enhanced resolution (ERES) |
Effective Number of Bits (ENOB) | 7.2 bits |
Vertical Noise Floor (1 mV/div) | 285 µV |
Vertical Noise Floor (2 mV/div) | 285 µV |
Vertical Noise Floor (5 mV/div) | 285 µV |
Vertical Noise Floor (10 mV/div) | 285 µV |
Vertical Noise Floor (20 mV/div) | 360 µV |
Vertical Noise Floor (50 mV/div) | 835 µV |
Vertical Noise Floor (100 mV/div) | 1.70 mV |
Vertical Noise Floor (200 mV/div) | 2.70 mV |
Vertical Noise Floor (500 mV/div) | 6.70 mV |
Vertical Noise Floor (1 V/div) | 11.93 mV |
Sensitivity | 50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable |
DC Vertical Gain Accuracy (Gain Component of DC Accuracy) | ±(0.5%) F.S, offset at 0 V |
Channel-Channel Isolation | 70dB up to 200 MHz 60dB up to 500 MHz 50dB up to 1 GHz 40dB up to 2.5 GHz 30dB up to 6 GHz |
Offset Range | 50 Ω, ≤1 GHz BWL 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-1V: +/-10V 50 Ω, >1 GHz BWL 1mV/div-34.5mV/div: +/- 0.5V 35mV/div-87mV/div: +/- 1.25V 88mV/div-220mV/div: +/-3V 225mV/div-1V/div: +/-5V 1 MΩ 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-100mV: +/-16V 102mV-198mV: +/-80V 200mV-1V: +/-160V 1.02V-10V: +/-400V |
DC Vertical Offset Accuracy | +/-(0.5% of offset value + 0.5%FS + 1mV) |
Maximum Input Voltage | 50 Ω, ≤1 GHz BWL 5V RMS, +/- 10V Peak 50 Ω, >1 GHz BWL '+/-2V max. up to 34.5mV/div +/-5V max. 35mV/div to 87mV/div 5.5Vrms >87mV/div 1 MΩ 400 V max (Peak DC+AC) |
Input Coupling | 1 MΩ: AC, DC, GND; 50 Ω: DC, GND |
Input Impedance | 50 Ω+/-2% or 1 MΩ||14pF, 10 MΩ || 9.5 pF |
Bandwidth Limiters | 20MHz, 200MHz, 500 MHz, 1 GHz, 2.5 GHz, 4 GHz |
Rescaling | Length: meters, inches, feet, yards, miles; Mass: grams, slugs; Temperature: celsius, fahrenheit, kelvin; Angle: radian, arcdegr, arcmin, arcsec, cycles, revolutions, turns; Velocity: m/s, in/s, ft/s, yd/s, miles/s; Acceleration: m/s2, in/s2, ft/s2, g0; Volume: liters, cubic meters, cubic inches, cubic feet, cubic yards; Force (Weight): newton, grain, ounce, pound; Pressure: pascal, bar, atmosphere (technical), atmosphere (standard), torr, psi; Electrical: volts, amps, watts, volt-amperes, volt-amperes reactive, farad, coulomb, ohm, siemen, volt/meter, coulomb/m2, farad/meter, siemen/meter, power factor; Magnetic: weber, tesla, henry, amp/meter, henry/meter; Energy: joule, Btu, calorie; Rotating Machine: radian/second, frequency, revolution/second, revolution/minute, N?m, lb-ft, lb-in, oz-in, watt, horsepower; Other: %. |
Horizontal - Analog Channels | |
Timebases | Internal timebase common to 4 input channels |
Acquisition Modes | Real-time |
Time/Division Range | 20ps/div - 1 ks/div |
Clock Accuracy | +/-100ppb for 5 to 40C + 0.10ppm/year from calibration |
Sample Clock Jitter | up to 10µs Acquired Time Range: 60 fsrms (Internal Timebase Reference) up to 10ms Acquired Time Range: 100 fsrms (Internal Timebase Reference) |
Delta Time Measurement Accuracy | \sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds) |
Jitter Measurement Floor | \sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)} |
Channel-Channel Deskew Range | ±9 x time/div. setting, 100 ms max., each channel |
External Timebase Reference (Input) | 10MHz +/-25ppm at 0 to 10dBm into 50Ohms |
External Timebase Reference (Output) | 10MHz, 5.0 dBm +/-2.5 dBm, sinewave synchronized to reference being used (internal or external reference) |
External Clock | N/A |
Acquisition - Analog Channels | |
Sample Rate (Single-shot) | 10 GS/s on 4 Ch 20 GS/s on 2 Ch |
Sample Rate (Repetitive) | N/A |
Memory Length (4 Ch / 2 Ch / 1Ch) (Number of Segments) | 50M/100M |
Memory Length Options (4 Ch / 2 Ch / 1Ch) (Number of Segments) | WPHD-200MPT Option: 100M / 200M WPHD-500MPT Option: 250M / 500M WPHD-1000MPT Option: 500M / 1000M WPHD-2000MPT Option: 1000M / 2000M WPHD-5000MPT Option: 2500M / 5000M |
Averaging | Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps (Waveforms of ≤500Mpts) |
Envelope (Extrema) | Envelope, floor, or roof for up to 1 million sweeps (Waveforms of ≤500Mpts) |
Interpolation | Linear or Sin x/x (2 pt and 5 pt) (Waveforms of ≤500Mpts) |
Vertical, Horizontal, Acquisition - Digital Channels | |
Maximum Input Frequency | 250 MHz |
Minimum Detectable Pulse Width | 2 ns |
Input Channels | 16 Digital channels |
Input Impedance (Flying Leads) | 100 kΩ || 5 pF |
Input Dynamic Range | ± 20V |
Maximum Input Voltage | ±30V Peak |
Maximum Input Voltage Swing | 400mV |
Threshold Groupings | Pod 2: D15 - D8, Pod 1: D7 - D0 |
Threshold Selections | TTL, ECL, CMOS (2.5 V, 3.3 V, 5 V), PECL, LVDS or User Defined |
Threshold Accuracy | ±(3% of threshold setting + 100mV) |
User Defined Threshold Range | ±10 V in 20 mV steps |
User Defined Hysteresis Range | 100 mV to 1.4 V in 100 mV steps |
Sample Rate | 1.25 GS/s |
Record Length | Standard: 50M WPHD-200MPT Option: 100M WPHD-500MPT Option: 125M WPHD-1000MPT Option: 125M WPHD-2000MPT Option: 125M WPHD-5000MPT Option: 125M |
Channel-to-Channel Skew | 350ps |
Triggering System | |
Modes | Acquisition of ≤500Mpts: Normal, Auto, Single, and Stop Acquisition of >500Mpts: Single |
Sources | Any input channel, Ext, Ext/10, Line, or Fast Edge; slope and level unique to each source (except Line and Fast edge) |
Coupling | DC, AC, HFRej, LFRej |
Pre-trigger Delay | 0-100% of memory size |
Post-trigger Delay | No limitation |
Hold-off | From 1 ns up to 20 s or from 1 to 99,999,999 events |
Trigger and Interpolator Jitter | ≤ 2.5 ps RMS (typical) <0.1 ps RMS (typical, software assisted) |
Internal Trigger Level Range | ±4.1 div from center (typical) |
External Trigger Level Range | Ext (±0.4 V); Ext/10 (±4 V) |
Maximum Trigger Rate | 650,000 waveforms/second (in Sequence Mode, up to 4 channels) |
Trigger Sensitivity with Edge Trigger ProBus Inputs | 0.75 div @ < 5 GHz 1.5 div @ < 6 GHz |
Trigger Sensitivity with Edge Trigger (Aux Input) | 0.5 div @ < 1 GHz |
Max. Trigger Frequency, SMART Trigger | 2.0 GHz @ ≥ 10 mV/div (minimum triggerable width 200 ps) |
Trigger Types | |
Edge | Triggers when signal meets slope (positive, negative, or either) and level condition. |
Width | Triggers on positive or negative glitches with selectable widths. Minimum width 500 ps, maximum width: 20 s |
Glitch | Triggers on positive or negative glitches with selectable widths. Minimum width 200 ps, maximum width: 20 s |
Window | Triggers when signal exits a window defined by adjustable thresholds |
Pattern | Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern. |
TV-Composite Video | Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative). |
Runt | Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns. |
Slew Rate | Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
Interval | Triggers on intervals selectable between 1 ns and 20 s. |
Dropout | Triggers if signal drops out for longer than selected time between 1 ns and 20 s. |
Measurement Trigger | Select from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger. |
Multi-Stage: Qualified (Timeout or State/Edge Qualified) | Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
Triggers with Exclusion Technology | Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met |
Multi-Stage: Qualified First | In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
TriggerScan | A Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially. |
Low Speed Serial Protocol Trigger (Optional) | |
Supported Protocols | I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, MIL-STD-1553, USB 1.x/2.0 |
Measurement Tools | |
Measurement Functionality | Display up to 12 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state. |
Measurement Parameters - Horizontal + Jitter | Cycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min |
Measurement Parameters - Vertical | Amplitude, Base, [email protected], Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top. |
Measurement Parameters - Pulse | Area, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%) |
Measurement Parameters - Statistical (on Histograms) | Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total) |
Math Tools | |
Math Functionality | Display up to 12 math functions traces (F1-F12). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math. |
Math Operators - Basic Math | Average (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+). |
Math Operators - Digital (incl. with MSO models/options) | Digital AND, Digital DFlipFlop, Digital NAND, Digital NOR, Digital NOT, Digital OR, Digital XOR |
Math Operators - Filters | Enhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x. |
Math Operators - Frequency Analysis | FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows. |
Math Operators - Functions | Absolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity). |
Math Operators - Other | Segment, Sparse |
Measurement and Math Integration | |
Measurement and Math Integration | Histograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma) |
Pass/Fail Testing | |
Pass/Fail Testing | Display up to 12 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value <. ≤, =, >, ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook. |
Display System | |
Size | Color 15.6" widescreen capacitive touch screen |
Resolution | 1920 x 1080 pixels |
Number of traces | Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces. |
Grid Styles | Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Quatro, Twelve, Sixteen |
Waveform Representation | Sample dots joined, or sample dots only |
Persistence Display | |
Analog and Color-Graded Persistence | Waveforms of ≤500Mpts: Variable saturation levels; stores each trace’s persistence data in memory |
Persistence Types | Waveforms of ≤500Mpts: Select analog, color, or three-dimensional |
Trace Selection | Waveforms of ≤500Mpts: Activate persistence on all or any combination of traces |
Persistence Aging | Waveforms of ≤500Mpts: Select from 500 ms to infinity |
Sweep Display Modes | Waveforms of ≤500Mpts: All accumulated, or all accumulated with last trace highlighted |
Zoom Expansion Traces | |
Zoom Expansion Traces | Display up to 12 Zoom and 12 Math/Zoom traces |
Internal Waveform Memory | |
Internal Waveform Memory | 12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity. |
Setup Storage | |
Front Panel and Instrument Status | Store to the internal hard drive, over the network, or to a USB-connected peripheral device. |
Automatic Setup | |
Auto Setup | Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals |
Find Vertical Scale | Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range |
Calibration | |
Auto Calibration | Ensures specified DC and timing accuracy is maintained for 1 year minimum. |
Processor/CPU | |
Type | Intel® Core i5-6500 Quad Core, 3.2 GHz (or better) |
Processor Memory | 16 GB standard |
Operating System | Microsoft Windows® 10 |
Oscilloscope Operating Software | Teledyne LeCroy MAUI™ with OneTouch |
Real Time Clock | Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks. |
Connectivity | |
Ethernet Port | 2 x 10/100/1000BaseT Ethernet interface (RJ45 port) |
USB Host Ports | 4 side USB 3.1 Gen1 ports, 3 front USB 3.1 Gen1 ports |
USB Device Port | 1 port - USBTMC over USB 3.1 Gen1 |
GPIB Port (optional) | Supports IEEE - 488.2 (External) |
External Monitor Port | 1 x DisplayPort, supports up to 4096x2304 @ 24 Hz 1 x HDMI, supports up to 4096x2304 @ 60 Hz |
Remote Control | Via Windows Automation, or via LeCroy Remote Command Set |
Network Communication Standard | VXI-11 or VICP, LXI Compatible |
Auxiliary Input | |
Signal Types | For external trigger input |
Coupling | 50 Ω: DC; 1 MΩ: AC, DC, GND |
Max. Input Voltage | 50 Ω 5V RMS, +/- 10V Peak 1 MΩ 400 V max (Peak DC+AC) |
Auxiliary Output | |
Signal Types | Select from outpout signal, control signals, off |
Output Signal | 500 Hz-5 MHz square wave or DC level; 50 mV-1 V into 1 MΩ |
Control Signals | Trigger enabled, trigger out, pass/fail status, fast edge, off |
Connector Type | BNC, located on front |
Probes | |
Probes | Qty. (4) ÷10 Passive Probes |
Probe System | ProBus2. Automatically detects and supports a variety of compatible probes. Fully backwards-compatible to ProBus probes without the use of adapters. |
Scale Factors | Automatically or manually selected depending on probe used |
Calibration Output | Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 500 Hz to 1 MHz square wave; 50 mV to 1.0V. |
Power Requirements | |
Voltage | 90 - 132 Vrms, 380 - 420Hz 90 - 264 Vrms, 47 - 63 Hz |
Nominal Power Consumption | 400W/400VA |
Max. Power Consumption | 525W/525VA |
Certifications | |
Certifications | CE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No. 61010-1-12 |
Environmental | |
Temperature (Operating) | +5 °C to +40 °C |
Temperature (Non-Operating) | -20 °C to +60 °C |
Humidity (Operating) | 5% to 90% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C. |
Humidity (Non-Operating) | 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F |
Altitude (Operating) | Up to 10,000 ft. (3048 m) at or below +30 °C |
Altitude (Non-Operating) | Up to 40,000 ft. (12,192 m) |
Random Vibration (Operating) | 0.31 grms 5 Hz to 500 Hz, 20 minutes in each of three orthogonal axes |
Random Vibration (Non-Operating) | 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes |
Functional Shock | 30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total |
Size and Weight | |
Dimensions (HWD) | 13.6” H x 17.5” W x 7.7” D (345 x 445 x 196 mm) |
Weight | 24.4 lbs (11.1 kg) |
Shipping Weight | 34 lbs |
Warranty and Service | |
Warranty and Service | 3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services. |

Vertical - Analog Channels | |
Analog Bandwidth (Max) | 8 GHz on 2 Ch 4 GHz on 4 Ch |
Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input) | 500 MHz (typical) |
Rise Time (10-90%, 50 Ω) | 57.5 ps |
Rise Time (20-80%, 50 Ω) | 40.5 ps |
Input Channels | 4 |
Vertical Resolution | 12 bits; up to 15 bits with enhanced resolution (ERES) |
Effective Number of Bits (ENOB) | 7.0 bits |
Vertical Noise Floor (1 mV/div) | 315 µV |
Vertical Noise Floor (2 mV/div) | 315 µV |
Vertical Noise Floor (5 mV/div) | 315 µV |
Vertical Noise Floor (10 mV/div) | 315 µV |
Vertical Noise Floor (20 mV/div) | 420 µV |
Vertical Noise Floor (50 mV/div) | 983 µV |
Vertical Noise Floor (100 mV/div) | 1.95 mV |
Vertical Noise Floor (200 mV/div) | 3.16 mV |
Vertical Noise Floor (500 mV/div) | 7.76 mV |
Vertical Noise Floor (1 V/div) | 13.81 mV |
Sensitivity | 50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable |
DC Vertical Gain Accuracy (Gain Component of DC Accuracy) | ±(0.5%) F.S, offset at 0 V |
Channel-Channel Isolation | 70dB up to 200 MHz 60dB up to 500 MHz 50dB up to 1 GHz 40dB up to 2.5 GHz 30dB up to 8 GHz |
Offset Range | 50 Ω, ≤1 GHz BWL 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-1V: +/-10V 50 Ω, >1 GHz BWL 1mV/div-34.5mV/div: +/- 0.5V 35mV/div-87mV/div: +/- 1.25V 88mV/div-220mV/div: +/-3V 225mV/div-1V/div: +/-5V 1 MΩ 1mV-4.95mV: +/-1.6V 5mV-9.8mV: +/-4V 9.9mV-19.8mV: +/-8V 20mV-100mV: +/-16V 102mV-198mV: +/-80V 200mV-1V: +/-160V 1.02V-10V: +/-400V |
DC Vertical Offset Accuracy | +/-(0.5% of offset value + 0.5%FS + 1mV) |
Maximum Input Voltage | 50 Ω, ≤1 GHz BWL 5V RMS, +/- 10V Peak 50 Ω, >1 GHz BWL '+/-2V max. up to 34.5mV/div +/-5V max. 35mV/div to 87mV/div 5.5Vrms >87mV/div 1 MΩ 400 V max (Peak DC+AC) |
Input Coupling | 1 MΩ: AC, DC, GND; 50 Ω: DC, GND |
Input Impedance | 50 Ω+/-2% or 1 MΩ||14pF, 10 MΩ || 9.5 pF |
Bandwidth Limiters | 20MHz, 200MHz, 500 MHz, 1 GHz, 2.5 GHz, 4 GHz, 6 GHz |
Rescaling | Length: meters, inches, feet, yards, miles; Mass: grams, slugs; Temperature: celsius, fahrenheit, kelvin; Angle: radian, arcdegr, arcmin, arcsec, cycles, revolutions, turns; Velocity: m/s, in/s, ft/s, yd/s, miles/s; Acceleration: m/s2, in/s2, ft/s2, g0; Volume: liters, cubic meters, cubic inches, cubic feet, cubic yards; Force (Weight): newton, grain, ounce, pound; Pressure: pascal, bar, atmosphere (technical), atmosphere (standard), torr, psi; Electrical: volts, amps, watts, volt-amperes, volt-amperes reactive, farad, coulomb, ohm, siemen, volt/meter, coulomb/m2, farad/meter, siemen/meter, power factor; Magnetic: weber, tesla, henry, amp/meter, henry/meter; Energy: joule, Btu, calorie; Rotating Machine: radian/second, frequency, revolution/second, revolution/minute, N?m, lb-ft, lb-in, oz-in, watt, horsepower; Other: %. |
Horizontal - Analog Channels | |
Timebases | Internal timebase common to 4 input channels |
Acquisition Modes | Real-time |
Time/Division Range | 20ps/div - 1 ks/div |
Clock Accuracy | +/-100ppb for 5 to 40C + 0.10ppm/year from calibration |
Sample Clock Jitter | up to 10µs Acquired Time Range: 60 fsrms (Internal Timebase Reference) up to 10ms Acquired Time Range: 100 fsrms (Internal Timebase Reference) |
Delta Time Measurement Accuracy | \sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds) |
Jitter Measurement Floor | \sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)} |
Channel-Channel Deskew Range | ±9 x time/div. setting, 100 ms max., each channel |
External Timebase Reference (Input) | 10MHz +/-25ppm at 0 to 10dBm into 50Ohms |
External Timebase Reference (Output) | 10MHz, 5.0 dBm +/-2.5 dBm, sinewave synchronized to reference being used (internal or external reference) |
External Clock | N/A |
Acquisition - Analog Channels | |
Sample Rate (Single-shot) | 10 GS/s on 4 Ch 20 GS/s on 2 Ch |
Sample Rate (Repetitive) | N/A |
Memory Length (4 Ch / 2 Ch / 1Ch) (Number of Segments) | 50M/100M (65,535) |
Memory Length Options (4 Ch / 2 Ch / 1Ch) (Number of Segments) | WPHD-200MPT Option: 100M / 200M (65,535) WPHD-500MPT Option: 250M / 500M (65,535) WPHD-1000MPT Option: 500M / 1000M (65,535) WPHD-2000MPT Option: 1000M / 2000M (65,535) WPHD-5000MPT Option: 2500M / 5000M (65,535) |
Intersegment Time | 1.5 us |
Averaging | Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps (Waveforms of ≤500Mpts) |
Envelope (Extrema) | Envelope, floor, or roof for up to 1 million sweeps (Waveforms of ≤500Mpts) |
Interpolation | Linear or Sin x/x (2 pt and 5 pt) (Waveforms of ≤500Mpts) |
Vertical, Horizontal, Acquisition - Digital Channels | |
Maximum Input Frequency | 250 MHz |
Minimum Detectable Pulse Width | 2 ns |
Input Channels | 16 Digital channels |
Input Impedance (Flying Leads) | 100 kΩ || 5 pF |
Input Dynamic Range | ± 20V |
Maximum Input Voltage | ±30V Peak |
Maximum Input Voltage Swing | 400mV |
Threshold Groupings | Pod 2: D15 - D8, Pod 1: D7 - D0 |
Threshold Selections | TTL, ECL, CMOS (2.5 V, 3.3 V, 5 V), PECL, LVDS or User Defined |
Threshold Accuracy | ±(3% of threshold setting + 100mV) |
User Defined Threshold Range | ±10 V in 20 mV steps |
User Defined Hysteresis Range | 100 mV to 1.4 V in 100 mV steps |
Sample Rate | 1.25 GS/s |
Record Length | Standard: 50M WPHD-200MPT Option: 100M WPHD-500MPT Option: 125M WPHD-1000MPT Option: 125M WPHD-2000MPT Option: 125M WPHD-5000MPT Option: 125M |
Channel-to-Channel Skew | 350ps |
Triggering System | |
Modes | Acquisition of ≤500Mpts: Normal, Auto, Single, and Stop Acquisition of >500Mpts: Single |
Sources | Any input channel, Ext, Ext/10, Line, or Fast Edge; slope and level unique to each source (except Line and Fast edge) |
Coupling | DC, AC, HFRej, LFRej |
Pre-trigger Delay | 0-100% of memory size |
Post-trigger Delay | No limitation |
Hold-off | From 1 ns up to 20 s or from 1 to 99,999,999 events |
Trigger and Interpolator Jitter | ≤ 2.5 ps RMS (typical) <0.1 ps RMS (typical, software assisted) |
Internal Trigger Level Range | ±4.1 div from center (typical) |
External Trigger Level Range | Ext (±0.4 V); Ext/10 (±4 V) |
Maximum Trigger Rate | 650,000 waveforms/second (in Sequence Mode, up to 4 channels) |
Trigger Sensitivity with Edge Trigger ProBus Inputs | 2.25 div @ < 8 GHz 1.25 div @ < 4.5 GHz 0.75 div @ < 1 GHz |
Trigger Sensitivity with Edge Trigger (Aux Input) | 0.5 div @ < 1 GHz |
Max. Trigger Frequency, SMART Trigger | 2.0 GHz @ ≥ 10 mV/div (minimum triggerable width 200 ps) |
Trigger Types | |
Edge | Triggers when signal meets slope (positive, negative, or either) and level condition. |
Width | Triggers on positive or negative glitches with selectable widths. Minimum width 500 ps, maximum width: 20 s |
Glitch | Triggers on positive or negative glitches with selectable widths. Minimum width 200 ps, maximum width: 20 s |
Window | Triggers when signal exits a window defined by adjustable thresholds |
Pattern | Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern. |
TV-Composite Video | Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative). |
Runt | Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns. |
Slew Rate | Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
Interval | Triggers on intervals selectable between 1 ns and 20 s. |
Dropout | Triggers if signal drops out for longer than selected time between 1 ns and 20 s. |
Measurement Trigger | Select from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger. |
Multi-Stage: Qualified (Timeout or State/Edge Qualified) | Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
Triggers with Exclusion Technology | Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met |
Multi-Stage: Qualified First | In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events. (Note: event B pattern trigger cannot include analog channels). |
TriggerScan | A Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially. |
Low Speed Serial Protocol Trigger (Optional) | |
Supported Protocols | I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, MIL-STD-1553, USB 1.x/2.0 |
Measurement Tools | |
Measurement Functionality | Display up to 12 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the location for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state. |
Measurement Parameters - Horizontal + Jitter | Cycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min |
Measurement Parameters - Vertical | Amplitude, Base, [email protected], Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top. |
Measurement Parameters - Pulse | Area, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%) |
Measurement Parameters - Statistical (on Histograms) | Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total) |
Math Tools | |
Math Functionality | Display up to 12 math functions traces (F1-F12). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math. |
Math Operators - Basic Math | Average (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+). |
Math Operators - Digital (incl. with MSO models/options) | Digital AND, Digital DFlipFlop, Digital NAND, Digital NOR, Digital NOT, Digital OR, Digital XOR |
Math Operators - Filters | Enhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x. |
Math Operators - Frequency Analysis | FFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows. |
Math Operators - Functions | Absolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity). |
Math Operators - Other | Segment, Sparse |
Measurement and Math Integration | |
Measurement and Math Integration | Histograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma) |
Pass/Fail Testing | |
Pass/Fail Testing | Display up to 12 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value <. ≤, =, >, ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook. |
Display System | |
Size | Color 15.6" widescreen capacitive touch screen |
Resolution | 1920 x 1080 pixels |
Number of traces | Display a maximum of 40 traces. Simultaneously display channel, zoom, memory and math traces. |
Grid Styles | Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y, Tandem, Quatro, Twelve, Sixteen |
Waveform Representation | Sample dots joined, or sample dots only |
Persistence Display | |
Analog and Color-Graded Persistence | Waveforms of ≤500Mpts: Variable saturation levels; stores each trace’s persistence data in memory |
Persistence Types | Waveforms of ≤500Mpts: Select analog, color, or three-dimensional |
Trace Selection | Waveforms of ≤500Mpts: Activate persistence on all or any combination of traces |
Persistence Aging | Waveforms of ≤500Mpts: Select from 500 ms to infinity |
Sweep Display Modes | Waveforms of ≤500Mpts: All accumulated, or all accumulated with last trace highlighted |
Zoom Expansion Traces | |
Zoom Expansion Traces | Display up to 12 Zoom and 12 Math/Zoom traces |
Internal Waveform Memory | |
Internal Waveform Memory | 12 active waveform memory traces (M1-M12) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity. |
Setup Storage | |
Front Panel and Instrument Status | Store to the internal hard drive, over the network, or to a USB-connected peripheral device. |
Automatic Setup | |
Auto Setup | Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals |
Find Vertical Scale | Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range |
Calibration | |
Auto Calibration | Ensures specified DC and timing accuracy is maintained for 1 year minimum. |
Processor/CPU | |
Type | Intel® Core i5-6500 Quad Core, 3.2 GHz (or better) |
Processor Memory | 16 GB standard |
Operating System | Microsoft Windows® 10 |
Oscilloscope Operating Software | Teledyne LeCroy MAUI™ with OneTouch |
Real Time Clock | Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks. |
Connectivity | |
Ethernet Port | 2 x 10/100/1000BaseT Ethernet interface (RJ45 port) |
USB Host Ports | 4 side USB 3.1 Gen1 ports, 3 front USB 3.1 Gen1 ports |
USB Device Port | 1 port - USBTMC over USB 3.1 Gen1 |
GPIB Port (optional) | Supports IEEE - 488.2 (External) |
External Monitor Port | 1 x DisplayPort, supports up to 4096x2304 @ 24 Hz 1 x HDMI, supports up to 4096x2304 @ 60 Hz |
Remote Control | Via Windows Automation, or via LeCroy Remote Command Set |
Network Communication Standard | VXI-11 or VICP, LXI Compatible |
Auxiliary Input | |
Signal Types | For external trigger input |
Coupling | 50 Ω: DC; 1 MΩ: AC, DC, GND |
Max. Input Voltage | 50 Ω 5V RMS, +/- 10V Peak 1 MΩ 400 V max (Peak DC+AC) |
Auxiliary Output | |
Signal Types | Select from outpout signal, control signals, off |
Output Signal | 500 Hz-5 MHz square wave or DC level; 50 mV-1 V into 1 MΩ |
Control Signals | Trigger enabled, trigger out, pass/fail status, fast edge, off |
Connector Type | BNC, located on front |
Probes | |
Probes | Qty. (4) ÷10 Passive Probes |
Probe System | ProBus2. Automatically detects and supports a variety of compatible probes. Fully backwards-compatible to ProBus probes without the use of adapters. |
Scale Factors | Automatically or manually selected depending on probe used |
Calibration Output | Default is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 500 Hz to 1 MHz square wave; 50 mV to 1.0V. |
Power Requirements | |
Voltage | 90 - 132 Vrms, 380 - 420Hz 90 - 264 Vrms, 47 - 63 Hz |
Nominal Power Consumption | 400W/400VA |
Max. Power Consumption | 525W/525VA |
Certifications | |
Certifications | CE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No. 61010-1-12 |
Environmental | |
Temperature (Operating) | +5 °C to +40 °C |
Temperature (Non-Operating) | -20 °C to +60 °C |
Humidity (Operating) | 5% to 90% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C. |
Humidity (Non-Operating) | 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F |
Altitude (Operating) | Up to 10,000 ft. (3048 m) at or below +30 °C |
Altitude (Non-Operating) | Up to 40,000 ft. (12,192 m) |
Random Vibration (Operating) | 0.31 grms 5 Hz to 500 Hz, 20 minutes in each of three orthogonal axes |
Random Vibration (Non-Operating) | 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes |
Functional Shock | 30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total |
Size and Weight | |
Dimensions (HWD) | 13.6” H x 17.5” W x 7.7” D (345 x 445 x 196 mm) |
Weight | 24.4 lbs (11.1 kg) |
Shipping Weight | 34 lbs |
Warranty and Service | |
Warranty and Service | 3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services. |
デモビデオ
|
主な機能
- 帯域幅:2.5GHz~8GHz(帯域アップグレード可能)
- 12ビットADC分解能
分解能向上演算(ERES)使用時に最大15ビット
− DCゲイン精度:±0.5%フルスケール - 最高サンプリング速度:20GS/s
- ロングメモリ:最長5Gポイント
- 15.6インチ、フルHDタッチ・スクリーン
OneTouch MAUI搭載
タブレット感覚のワンタッチ操作- 8GHz ProBus2プローブ・インタフェース
- デジタル16ch(WavePro HD-MSのみ)
- WavePro HDからWavePro HD-MSへのアップグレード可能
- LabNotebook − 測定をまるごとアーカイブ
- Windows 10
16倍の分解能

HD4096テクノロジによる12ビットの垂直分解能は、一般的な8ビット・オシロスコ ープと比較して16倍の分解能を提供し、量子化エラーを低減します。また、8GHzの広い帯域ながらローノイズの入力増幅器との組み合わせで0.5%のDCゲイン精度を達成しています。これは、信号捕捉の精度と計測の信頼性を向上させます。
業界初!5Gポイントの超ロングメモリ
WavePro HDシリーズは、これまでの波形メモリの上限を打ち破り、最大で5Gポイントと業界最高のロングメモリを実現しました。また、20GS/sの高速サンプリングでも250msもの長時間の信号捕捉が可能となり、波形検索機能など豊富なツールで稀な異常現象を特定することができます。
新たに開発したチップセットがHD4096を8GHz帯域に拡張
20GS/sの高サンプリング速度で12ビット分解能を実現するA/D変換器と8GHz帯域の広帯域ローノイズ入力増幅器を新たに開発し、システムレベルでのローノイズ設計とあわせて8GHzの広帯域でもDCゲイン精度0.5%を実現しています。
8GHz帯域のProBus2プローブ・インタフェース

オシロスコープの入力には、BNC互換で8GHzの帯域を持つコネクタを新たに採用したProBus2プローブ・インタフェースを採用しました。従来のProBusインタフェースと互換性があるので、ProBus対応のプローブはそのままお使いいただけます。
主なアプリケーション
携帯機器や高速の組み込みコンピュータ・システム

- 微小なアナログ・センサ信号を 正確に計測する高分解能
- 最適なパワーインテグリティ検証
- 強力なシリアル・データ解析機能
- シリアル・データのトリガ/デコード機能
- 16チャンネル・デジタル信号捕捉
シリアル・データ解析

- ローノイズ12ビット高分解能と低ジッタ特性がシリアル・データ解析にもたらす高い精度
- シリアル・データ解析オプションは、ジッタとノイズの抽出と計測、アイパターンの比較と独自の可視化機能によって問題を検出
- 自動コンプライアンス試験オプションによりDDRメモリ、イーサネット、USBなどのインタフェースの検証が容易に
パワー・インテグリティのデバッグと検証

- 低電圧化もあり、外乱の影響を受けやすい電源供給ネットワーク (PDN)の電源ノイズを広帯域、12ビット分解能により捕捉可能
- 業界最高のツール─4GHz帯域の 電源レール・プローブによる 柔軟なプロービングが可能
- 低いノイズ・フロアによる 高度なスペクトラム解析が可能
電磁適合性(EMC/EMI)

試験パルスの検証には2GHzを超える帯域が必要で、かつ高精度に計測する必要があります。8GHz帯域でかつ12ビットの分解能を持つWavePro HDシリーズは、まさに理想的なツールとなります。
クリックで詳細表示されます
メモリオプション
コンピュータ・アップグレード
帯域アップグレード
MSOへのアップグレード
リモート・コントロール/ネットワーク・オプション
電源解析
トリガ/デコード・オプション
ジッタ解析パッケージ
デジタル・フィルタ・パッケージ
コンプライアンス・テスト・オプション
シリアル・データ解析
その他
クリックで詳細表示されます