Software Options


MultiGBase-T1 is designed to meet the requirements of a high-performance backbone in domain and zonal vehicle architectures. QPHY-MultiGBase-T1 automates testing and validation of 2.5 Gb/s, 5 Gb/s, and 10 Gb/s Automotive Ethernet, which is described in MultiGBase-T1 (IEEE 802.3cg) specification.

Explore QPHY-MultiGBase-T1 arrow down
product title image
  • product line tab
  • overview tab
  • compatability tab
Key Features
  • Support for 2.5/5/10 G MultiGBase-T1 (IEEE 802.3cg)
  • Highly automated and easy-to-use
  • Complete test solution including test fixture, signal generator & cables
  • Report generation with pass/fail results and fully annotated screenshot
  • Supports all PMA Transmitter Tests
    • Maximum Output Droop
    • Transmitter Linearity
    • Transmitter Timing Jitter
    • RJ Transmitter MDI Random Jitter
    • DJ Transmitter MDI Deterministic Jitter - Pk-Pk Deterministic Jitter (DJpk-pk)
    • DJ Transmitter MDI Deterministic Jitter - Pk-Pk Even Odd Jitter (EOJpk-pk)
    • Transmitter Power Spectral Density (PSD) and Power
    • Transmitter Peak Differential Output
  • Advanced debugging ability with "Stop on Test"


Automated Compliance Testing

QPHY-MultiGBase-T1 performs electrical compliance testing of the Physical Media Attachment (PMA) according to the MultiGBase-T1 specification. Detailed connection diagrams ensure the proper setup and provide information about the required test pattern for each test. Upon completion of the test session, results are automatically compiled into a comprehensive report including screenshots.

Flexible Debug Environment

Using the "Stop on Test" feature, the user can pause testing after each individual test and observe the results. At that point, any of the oscilloscope’s tools can be leveraged for further debug and upon completion, testing can be seamlessly resumed with a click of a button.

Maximum Output Droop

The droop test is performed to ensure that there is not excessive filtering happening between the transmitter output and the MDI output (connector). Droop is calculated after measuring the voltage 4 ns after the initial zero crossings (Vinit) and the voltage 16 ns after the zero crossing (Vdelay).

Transmitter Linearity

The transmitter linearity test verifies that the transmitter Signal-to-noise and distortion ratio (SNDR) exceed the specified amount. The signal is measured in Test Mode 4 while the PHY is transmitting a continuous PAM4 signal with PRBS13Q pattern.

Transmitter Timing Jitter

For MultiGBase-T1 the jitter is measured under different conditions. The first two, which are called transmitter timing jitter, are measured on the 175 MHz clock output where the DUT is in master or slave configuration. The next one is called transmit MDI random jitter and it is measured on the MDI interface when the DUT is sending a pattern which is similar to a 175 MHz clock signal.

Transmitter MDI Deterministic Jitter

This test measures the deterministic jitter on the MDI interface using two different patterns and setups. The first test measures the deterministic jitter (DJpk-pk) using the JP03A test pattern and the second test measures the Even Odd Jitter (EOJpk-pk) using JP03B test pattern.

Transmitter Power Spectral Density and Power

The Power Spectrum Density (PSD) measures a signal's power content versus frequency and shows how the energy of a signal is distributed. Using the oscilloscope for the PSD test removes the need to purchase a spectrum analyzer.


WavePro HD Oscilloscopes

WavePro HD Oscilloscopes
  Learn More
WaveMaster / SDA / DDA 8 Zi-B Oscilloscopes

  Learn More
WaveMaster 8000HD

  Learn More
LabMaster 10 Zi-A Oscilloscopes

  Learn More