8A350197-63B6-4AE9-A506-E97B9573E47A Created with sketchtool.
Serial Data

QualiPHY

QualiPHY is designed to reduce the time and effort needed to perform compliance testing on a wide array of high-speed serial buses. QualiPHY is the most intuitive and efficient tool available for performing serial data compliance testing. Selecting a new standard or test setup is done without leaving the main screen, and the user can start testing with a single button press.

Explore QualiPHY Explore QualiPHY
QPHY-USB4-TX-RX   QualiPHY automates USB4™ (Universal Serial Bus 4) physical layer (PHY) testing in accordance with the USB-IF USB4 and Thunderbolt 3 CTS (Compliance Test Specifications) over the USB Type-C® connector. The Teledyne LeCroy LabMaster SDA 10 Zi-A Oscilloscope, WavePulser 40iX High-speed Interconnect Analyzer, and Anritsu MP1900A Signal Quality Analyzer-R BERT (Bit Error Rate Tester) compose a comprehensive system that provides USB4 test engineers with an integrated electrical test solution.
QPHY-10Base-T1S   Automotive Ethernet enables faster data communication to meet the demands of today’s vehicles and the connected vehicles of the future. QPHY-10Base-T1S automates testing and validation of 10 Mb/s Automotive Ethernet, which is described in 10Base-T1S (IEEE 802.3cg) specification.

MDI Return Loss and Mode Conversion tests also available with QPHY-10Base-T1-TDR.

QPHY-10Base-T1-TDR   QPHY-10Base-T1-TDR automates MDI S-parameter compliance testing and validation of 10 Mb/s Ethernet, which is described in the 10Base-T1S and 10Base-T1L (IEEE 802.3cg) specifications. Return Loss (Sdd11) and Mode Conversion Loss (Sdc11) are measured using the WavePulser 40iX Time Domain Reflectometer (TDR).
QPHY-DisplayPort 2.0   QPHY-DP2.0-SOURCE provides the fastest way to perform compliance testing on DisplayPort 2.0 Source device transmitters, while QPHY-DP2.0-SINK provides simple, repeatable compliance testing on Sink device receivers.
QPHY-MIPI-CPHY   QPHY-MIPI-CPHY simplifies and automates MIPI C-PHY transmitter conformance testing. It also integrates the CPHYbus DMP option to provide powerful decode and search capabilities, automated measurement and graphing tools, and MIPI C-PHY standard-specific capability for physical layer signal assessment, debug, and eye diagram creation.
QPHY-PCIE3-TX-RX   PCI Express 3.0 introduces a new set of physical-layer testing demands, as sophisticated protocol-aware capabilities are required at transfer rates of 8 Gb/s. Teledyne LeCroy's LabMaster 10 Zi-A or WaveMaster 8 Zi-B oscilloscope combined with the Anritsu Signal Quality Analyzer (SQA) MP1900A BERT delivers a comprehensive system that provides high-speed IC, device, and network engineers with an integrated test solution to conduct automated compliance testing, accelerate debug and ensure faster time-to-market.
QPHY-10Base-T1L   Single Pair Ethernet (SPE) describes the transmission of Ethernet via only one pair of copper wires and provides a space- and cost-efficient infrastructure for the Industrial Internet of Things (IIoT). QPHY-10Base-T1L automates testing and validation of 10 Mb/s Single Pair Ethernet, which is described in 10Base-T1L (IEEE 802.3cg) specification.

MDI Return Loss and Mode Conversion tests also available with QPHY-10Base-T1-TDR.
QPHY-MultiGBaseT1-TDR   QPHY-MultiGBase-T1-TDR automates MDI S-parameter and TC9 Link Segments compliance testing and validation of 2.5G/5G/10GBase-T1. MDI Return Loss, Characteristic Impedance Differential Mode (CDIM), Propagation Delay, Insertion Loss, Return Loss and Longitudinal Conversion Transfer Loss (LCTL) are measured using the WavePulser 40iX Time Domain Reflectometer (TDR).
QPHY-10GBase-KR   The Teledyne LeCroy QPHY-10GBase-KR solution automates testing for 10Gigabite Ethernet Copper Backplane base on the IEEE 802.3ap specifications. The test framework simplifies the test setup and execution of generic and common test requirements such as jitter separation, rise/fall time and transmitter equalization parameters. The guided wizard prompts the user to for specification required patterns and takes the measurements accordingly. The test report includes the test results pass/fail summary, margins and limits, as well as waveforms and measurements used during the test process.
QPHY-10GBASE-T   QPHY-10GBASE-T automated compliance test software performs electrical compliance testing of the Physical Media Attachment (PMA) for 10GBASE-T Ethernet PHY, based on IEEE802.3-2008 requirements.
QPHY-56G-PAM4   PAM4 interfaces running at 28 Gbaud enable 56 Gb/s data rates, with rapidly-evolving standards that define a challenging set of test requirements for designers and test engineers. Teledyne LeCroy’s QPHY-56G-PAM4 simplifies and automates testing to PAM4-based interface standards.
QPHY-DDR2   The Teledyne LeCroy QPHY-DDR2 Test Solution is the best way to characterize DDR2 memory interfaces. Capable of performing measurements on 400 MHz, 533 MHz, 667 MHz, 800 MHz, 1066 MHz and custom speed grades, QPHY-DDR2 has a full suite of Clock, Electrical and Timing tests as specified by the JEDEC Specification and Intel JEDEC Specifications Addendums.
QPHY-DDR3   The Teledyne LeCroy QPHY-DDR3 Test Solution is the best way to characterize DDR3, DDR3L, and LPDDR3 memory interfaces. Capable of performing measurements on 800 MT/s, 1066 MT/s, 1333 MT/s, 1600 MT/s, 1866 MT/s, 2133 MT/s and custom speed grades, QPHY-DDR3 has a full suite of Clock, Electrical, and Timing tests as specified by the JEDEC Specification.
QPHY-DDR4   DDR4, LPDDR4 and LPDDR4X are evolutionary upgrades from previous generations of DDR3 and LPDDR3. It introduces data transfer rates which are nearly double the previous transfer rates, ranging from 1.6 GT/s up to 4.2 GT/s. DDR4's higher transfer rates and lower operating voltage have driven new test methodologies and test requirements which were not previously required to ensure proper signal fidelity. QPHY-DDR4 has a full suite of Clock, Electrical, and Timing tests as specified by the JEDEC Specification which will aid in DDR4, LPDDR4 and LPDDR4X design validation. Meanwhile the Debug Toolkit is a separate tool that assists with turn-on, multi-scenario debug and is a great assisting toolset whenever you need to manually dig a little deeper.
QPHY-DisplayPort 1.4   DisplayPort 1.4 Electrical Test Solution

The QPHY-DisplayPort software option provides an automated test environment for running all of the normative real-time oscilloscope tests for sources in accordance with Version 1.4a of the Video Electronics Standards Association (VESA) DisplayPort PHY Compliance Test Specification, and with Version 1.0a of the VESA DisplayPort Alt mode on USB Type-C Compliance Test Specification.
QPHY-eDP   QPHY-eDP provides a highly automated and easy-to-use solution for Embedded DisplayPort source testing in accordance with version 1.4 of the VESA Embedded DisplayPort PHY compliance test guideline.
QPHY-ENET   Ethernet testing compliant with IEEE 802.3-2005 requires many test setups and connections and mask tests. Using Teledyne LeCroy QualiPHY-ENET these measurements are easy to setup and complete. Instructive connection diagrams and message boxes appear as pop ups on the oscilloscope screen. The connection diagram instructs the user how to change test fixture and jumper pins in order to do complete test. When the tests are complete, QualiPHY will generate a test report in PDF, HTML, or XML formats. Jitter and pulse mask tests are performed with automatic waveform alignment, and all test results feature pass/fail indicators corresponding to the standard being tested.
QPHY-HDMI2.0 and QPHY-HDMI2.1   The QPHY-HDMI2.1 Test Solution for the LabMaster 10Zi-A and SDA 8Zi-B oscilloscopes provides a highly automated and easy-to-use solution for HDMI 2.1 Source testing in accordance with Version 2.1 of the HDMI Compliance Test Specification. Including all FRL and TMDS electrical tests required for 2.1/2.0/1.4b compliance.
QPHY-LPDDR2   The Teledyne LeCroy QPHY-LPDDR2 Test Solution is the best way to characterize LPDDR2 memory interfaces. Capable of performing measurements on 466 MHz, 533 MHz, 667 MHz, 800 MHz, 900 Mhz, 1066 MHz and custom speed grades, QPHY-LPDDR2 has a full suite of Clock, Electrical and Timing tests as specified by the JEDEC Specifications.
QPHY-MIPI-DPHY - D-PHY Compliance Package   Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing transmitter physical layer tests as described by the MIPI Alliance Specification for D-PHY version 1.00.00
QPHY-MIPI-MPHY   The QPHY-MIPI-MPHY Test Solution provides automated control of Teledyne LeCroy oscilloscopes for performing transmitter physical layer tests as described by the MIPI Alliance Specification for M-PHY version 3.0.
QPHY-MOST150   The Teledyne LeCroy QPHY-MOST150 compliance test package provides a highly automated and easy-to-use solution to MOST compliance testing. QPHY-MOST150 will perform all electrical compliance tests as defined in the MOST150 oPHY Automotive Physical Layer Sub-Specification Rev. 1.1 and MOST150 cPHY Automotive Physical Layer Sub-Specification Rev 1.0.
QPHY-100Base-T1   Automotive Ethernet enables faster data communication to meet the demands of today’s vehicles and the connected vehicles of the future. QPHY-100Base-T1 automates testing and validation of 100 Mb/s Automotive Ethernet, which is described in 100Base-T1 (IEEE 802.3bw), BroadR-Reach and TC8 specifications.

MDI Return Loss and Mode Conversion tests also available with QPHY-100Base-T1-TDR.

QPHY-MultiGBase-T1   MultiGBase-T1 is designed to meet the requirements of a high-performance backbone in domain and zonal vehicle architectures. QPHY-MultiGBase-T1 automates testing and validation of 2.5 Gb/s, 5 Gb/s, and 10 Gb/s Automotive Ethernet, which is described in MultiGBase-T1 (IEEE 802.3cg) specification.
QPHY-MOST50   The Teledyne LeCroy QPHY-MOST50 compliance test package provides a highly automated and easy-to-use solution to MOST compliance testing. QPHY-MOST50 will perform all electrical compliance tests as defined in the MOST Electrical Physical Layer Specification Rev. 1.1.
QPHY-PCIe   The Teledyne LeCroy QPHY-PCIe Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing the entire transmitter physical layer tests as described by the Card Electro-mechanical specification Rev 1.1 and 2.0
QPHY-100Base-T1-TDR   QPHY-100Base-T1-TDR automates MDI S-parameter compliance testing and validation of 100 Mb/s Automotive Ethernet, which is described in the 100Base-T1 (IEEE 802.3bw), BroadR-Reach, and TC8 specifications. Return Loss (Sdd11) and Mode Conversion Loss (Sdc11) are measured using the WavePulser 40iX Time Domain Reflectometer (TDR).
QPHY-1000Base-T1   Automotive Ethernet enables faster data communication to meet the demands of today’s vehicles and the connected vehicles of the future. QPHY-1000Base-T1 automates testing and validation of 1 Gb/s Automotive Ethernet, which is described in the 1000Base-T1 (IEEE 802.3bp) and TC8 specifications.

MDI Return Loss and Mode Conversion tests also available with QPHY-1000Base-T1-TDR.

QPHY-PCIE4-TX-RX   PCI Express 4.0 introduces a new set of physical-layer testing demands, as sophisticated protocol-aware capabilities are required at transfer rates of 16 Gb/s. Teledyne LeCroy's LabMaster 10 Zi-A oscilloscope combined with the Anritsu Signal Quality Analyzer (SQA) MP1900A BERT delivers a comprehensive system that provides high-speed IC, device, and network engineers with an integrated test solution to conduct automated compliance testing, accelerate debug and ensure faster time-to-market.
QPHY-PCIE5-TX-RX   PCI Express 5.0 introduces a new set of physical-layer testing demands at a transfer rate of 32 Gb/s. QPHY-PCIE5-TX-RX addresses these challenges with a fully-integrated compliance test solution for both Transmitter (Tx) and Receiver (Rx) testing to the PCI Express 5.0 Base specification and CEM specification, including receiver test calibration with the Anritsu MP1900A SQA-R.
QPHY-PCIE6-TX-RX   PCI Express 6.0 introduces a new set of physical-layer testing demands at a transfer rate of 64 Gb/s. QPHY-PCIE6-TX-RX addresses these challenges with a fully automated test solution for both Transmitter (Tx) and Receiver (Rx) testing to the PCI Express 6.0 Base specification. PCI Express 5.0, 4.0, and 3.0 transmitter, receiver and link equalization testing are also supported, for complete PCIe ecosystem coverage.
QPHY-SAS2   The Teledyne LeCroy QPHY-SAS2 Test Solution provides automated control for the SDA 8 Zi series of oscilloscopes for performing all of the transmitter physical layer tests as described by version 1.01 of the UNH IOL Serial Attached SCSI (SAS) Consortium SAS-2 6Gb/s Physical Layer Test Suite. This specification covers targets and initiators running at 1.5 Gb/s, 3.0 Gb/s and 6.0 Gb/s.
QPHY-1000Base-T1-TDR   QPHY-1000Base-T1-TDR automates MDI S-parameter compliance testing and validation of 1 Gb/s Automotive Ethernet, which is described in the 1000Base-T1 (IEEE 802.3bp) and TC8 specifications. Return Loss (Sdd11) and Mode Conversion Loss (Sdc11) are measured using the WavePulser 40iX Time Domain Reflectometer (TDR).
QPHY-SAS3   The QPHY-SAS3 Test Solution provides automated control of the SDA 8 Zi-A and LabMaster 10 Zi oscilloscopes for performing all of the transmitter physical layer tests as described by the T10 SAS-3 specification. This specification covers targets and initiators running at 1.5 Gb/s, 3.0 Gb/s, 6.0 Gb/s, and 12.0 Gb/s.
QPHY-SATA-TSG-RSG   QPHY-SATA-TSG-RSG is an automated test solution for SATA compliance testing to be used in conjunction with the PeRT3. By leveraging the capabilities of both the oscilloscope and the PeRT3, QPHY-SATA-TSG-RSG can automatically perform all of the PHY, TSG, OOB, and RSG tests as described by the SATA UTD 1.5. Furthermore, QPHY-SATA-TSG can be configured to test Gen1, Gen2, and Gen3 SATA PUTs.
QPHY-SFI   The Teledyne LeCroy QPHY-SFI solution automates testing for SFI base on the SFF 8431 specifications. The test framework simplifies the test setup and execution of generic and common test requirements such as jitter separation, rise/fall time and transmitter equalization parameters. The guided wizard prompts the user to for specification required patterns and takes the measurements accordingly. The test report includes the test results pass/fail summary, margins and limits, as well as waveforms and measurements used during the test process.
QPHY-USB   The USB package provides a complete acquisition and analysis system for USB 2.0 devices, hosts, and hubs, as specified in the USB-IF USB 2.0 Electrical Test Specification. The test software implements a full set of electrical tests for USB 2.0, including High-, Full-, and Low-speed tests and is supported by Teledyne LeCroy’s QualiPHY automated test and reporting software.
QPHY-USB3.2-Tx-Rx   Since becoming the first USB-IF "Gold Suite" in 2011, Teledyne LeCroy continues to be the trusted leader in all the latest USB Type-C technologies including USB 3.2 Tx/Rx “Gold Suite” compliance testing, the deepest USB 3.2 signal integrity (SI) toolbox, and unmatched PHY-logic and sideband debug.
Features
  • Easy-to-use
  • Guides the user through each required test setup
  • Automatically performs each required measurement in accordance with the relevant test procedure
  • Compares each measured value with the applicable specification limits
  • Fully documents all results
  • Offers adjustable limits for margin or production testing
  • Builds a database of results to facilitate further analysis

The rapid proliferation of high-speed serial data buses in today's computers and consumer electronics equipment presents a difficult challenge. Validating the proper operation of every device on every data bus is typically a tedious and time-consuming process, made even more complicated by the fact that each serial data standard employs it own unique terminology, measurements and test methods.

QualiPHY is designed to reduce the time and effort needed to perform compliance testing on a wide array of high-speed serial buses. QualiPHY is the most intuitive and efficient tool available for performing serial data compliance testing. Selecting a new standard or test setup is done without leaving the main screen, and the user can start testing with a single button press.

Comprehensive Reporting

QualiPHY creates professional quality reports that fully document all test results. QualiPHY can produce reports in standard HTML and PDF formats, and the user may easily customize the look of the reports by modifying the report style sheets.

Powerful Database Support

QualiPHY enables the user to export test data directly to XML format, which is readable by database programs such as Microsoft Access. This capability is highly useful to:

  • IC developers, who must fully characterize their devices over a wide range of conditions to establish and verify operating thresholds.
  • System level validation teams working in parallel development cycles, which need to combine, study, and interpret performance data and correlate various batches of test results.
  • Manufacturing groups, where key parameters need to be monitored as indicators of product/process performance.
Global Connectivity

QualiPHY has been developed with today's global design environment in mind. QualiPHY may be executed directly on the host oscilloscope, or it may be run on a computer located anywhere in the world, accessing the oscilloscope via GPIB or LAN/WAN connections. Development team members can also access live signals from oscilloscopes in remote locations.

Also of Interest